MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors General Description Applications The drivers maintain the 5V EIA/TIA-232E output signal levels at data rates in excess of 120kbps when loaded in accordance with the EIA/TIA-232E specification. Typical Operating Circuit MAX200-MAX209, MAX211, and MAX213 are a family of RS-232 and V.28 transceivers with integrated charge pump circuitry for single +5V supply operation. Battery-Powered Equipment Handheld Equipment Portable Diagnostics Equipment +5V INPUT The MAX211 and MAX213 are available in a 28-pin, wide small-outline (SO) package and a 28-pin shrink smalloutline (SSOP) package, which occupies only 40% of the area of the SO. The MAX207 is available in a 24-pin SO package and a 24-pin SSOP. The MAX203 and MAX205 use no external components and are recommended for applications with limited circuit board space. 0.1F 8 0.1F +6.3V 10 11 0.1F +16V 12 7 VCC C1+ +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V+ V- 9 0.1F +6.3V 13 0.1F +16V +5V Benefits and Features 400k Saves Board Space * Integrated Charge Pump Circuitry Eliminates the Need for a Bipolar 12V Supply Enables Single Supply Operation From Either +5V or 9V to +12V 5 T1IN T1 +5V T1OUT 2 400k 4 T2IN T2 +5V * Integrated 0.1F Capacitors (MAX203, MAX205) * 24 pin SSOP Package Saves Up to 40% Versus SO Package Saves Power for Longer Battery Operation * 5W Shutdown Mode (MAX200, MAX205, MAX206, MAX211) * 75W Ring Indicator Monitoring with Two Active Receivers (MAX213) T2OUT 3 400k TTL/CMOS INPUTS 14 T3IN T3 +5V T3OUT 1 RS-232 OUTPUTS 400k 15 T4IN T4 +5V T4OUT 20 400k 19 T5IN N.C. 18 T5 MAX200 T5OUT 16 17 SHDN GND 6 Selector Guide POWER-SUPPLY VOLTAGE (V) NUMBER OF RS-232 DRIVERS NUMBER OF RS-232 RECEIVERS NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN NUMBER OF EXTERNAL CAPACITORS (0.1F) LOW-POWER SHUTDOWN/TTL THREE-STATE MAX200 +5 5 0 0 4 Yes/No MAX201 +5 and +9.0 to +13.2 2 2 0 2 No/No MAX202 +5 2 2 0 4 No/No MAX203 +5 2 2 0 None No/No PART Selector Guide continued at end of data sheet. 19-0065; Rev 8; 1/15 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Absolute Maximum Ratings VCC...........................................................................-0.3V to +6V V+............................................................... (VCC - 0.3V) to +14V V- ............................................................................+0.3V to -14V Input Voltages TIN......................................................... -0.3V to (VCC + 0.3V) RIN....................................................................................30V Output Voltages TOUT.................................................(V+ + 0.3V) to (V- - 0.3V) ROUT..................................................... -0.3V to (VCC + 0.3V) Short-Circuit Duration TOUT.......................................................................Continuous Continuous Power Dissipation (TA = +70C) 14-Pin Plastic DIP (derate 10.00mW/C above +70C).... 800mW 16-Pin Plastic DIP (derate 10.53mW/C above +70C).... 842mW 16-Pin SO (derate 8.70mW/C above +70C)..............696mW 16-Pin Wide SO (derate 9.52mW/C above +70C)....762mW 16-Pin CERDIP (derate 10.00mW/C above +70C)......800mW 20-Pin Plastic DIP (derate 11.11mW/C above +70C).... 889mW 20-Pin Wide SO (derate 10.00mW/C above +70C)...800mW 20-Pin CERDIP (derate 11.11mW/C above +70C)....889mW 24-Pin Narrow Plastic DIP (derate 13.33mW/C above +70C)........................1067mW 24-Pin Wide Plastic DIP (derate 9.09mW/C above +70C)............................727mW 24-Pin Wide SO (derate 11.76mW/C above +70C)...941mW 24-Pin SSOP (derate 8.00mW/C above +70C).........640mW 24-Pin CERDIP (derate 12.50mW/C above +70C)....1000mW 28-Pin Wide SO (derate 12.50mW/C above +70C)...1000mW 28-Pin SSOP (derate 9.52mW/C above +70C).........762mW Operating Temperature Ranges MAX2_ _C_ _......................................................0C to +70C MAX2_ _E_ _.................................................. -40C to +85C MAX2_ _ M_ _............................................... -55C to +125C Storage Temperature Range............................. -65C to +160C Lead Temperature (soldering, 10s) (Note 1).................... +300C Note 1: Maximum reflow temperature for the MAX203 and MAX205 is +225C. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (MAX202/MAX204/MAX206/MAX208/MAX211/MAX213: VCC = +5V 10%; MAX200/MAX203/MAX205/MAX207: VCC = +5V 5%, C1-C4 = 0.1F; MAX201/MAX209: VCC = +5V 10%, V+ = +9.0V to +13.2V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER Output-Voltage Swing VCC Power-Supply Current CONDITIONS All transmitter outputs loaded with 3k to ground No load, TA = +25C 11 20 MAX201, MAX209 0.4 1 MAX201 5 10 MAX209 7 15 MAX200, MAX205, MAX206, MAX211 1 10 MAX213 15 50 Input Logic Threshold Low TIN, EN, SHDN, EN, SHDN RS-232 Input-Voltage Operating Range www.maximintegrated.com 0.8 2.0 15 -30 mA mA A V V 2.4 TIN = 0V UNITS V MAX200, MAX204-MAX208, MAX211, MAX213 Figure 1, TA = +25C Logic Pullup Current MAX 15 Shutdown Supply Current EN, SHDN, EN, SHDN 8 8 No load TIN TYP 5 MAX202, MAX203 V+ Power-Supply Current Input Logic Threshold High MIN 200 A +30 V Maxim Integrated 2 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Electrical Characteristics (continued) (MAX202/MAX204/MAX206/MAX208/MAX211/MAX213: VCC = +5V 10%; MAX200/MAX203/MAX205/MAX207: VCC = +5V 5%, C1-C4 = 0.1F; MAX201/MAX209: VCC = +5V 10%, V+ = +9.0V to +13.2V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER CONDITIONS MIN TYP MAX UNITS Receiver Input Threshold Low VCC = +5V, TA = +25C Active mode 0.8 1.2 Shutdown mode, MAX213, R4, R5 0.6 1.5 Receiver Input Threshold High VCC = +5V, TA = +25C Active mode 1.7 2.4 Shutdown mode, MAX213, R4, R5 1.5 2.4 RS-232 Input Hysteresis VCC = +5V, no hysteresis in shutdown 0.2 0.5 1.0 V 3 5 7 k 0.4 V RS-232 Input Resistance TTL/CMOS Output-Voltage Low VCC = +5V, TA = +25C IOUT = 3.2mA IOUT = 1.6mA MAX201, MAX202, MAX203 All others V V TTL/CMOS Output-Voltage High IOUT = 1.0mA TTL/CMOS Output Leakage Current EN = VCC, EN = 0V, 0 ROUT VCC Output Enable Time Figure 2 MAX205, MAX206, MAX209, MAX211, MAX213 600 ns Output Disable Time Figure 2 MAX205, MAX206, MAX209, MAX211, MAX213 200 ns Receiver Propagation Delay SHDN = 0V, R4, R5 SHDN = VCC 3.5 0.05 MAX213 MAX200-MAX211 Transmitter Output Resistance VCC = V+ = V- = 0V, VOUT = 2V Transition Region Slew Rate CL = 50pF to 2500pF, RL = 3k to 7k, VCC = 5V, TA = +25C measured from +3V to -3V or -3V to +3V MAX200, MAX202-MAX211, MAX213 www.maximintegrated.com 10 4 40 0.5 10 0.5 10 300 3 A s 5.5 30 V/s MAX201 RS-232 Output ShortCircuit Current Maximum Data Rate V RL = 3k to 7k, CL = 50pF to 1000pF, one transmitter 120 4 30 10 60 mA kbps Maxim Integrated 3 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Typical Operating Characteristics 4 Tx OUTPUT VOLTAGE (IVI) 2 5000 20kbps 9.0 8.0 VCC = +5V ALL Tx OUTPUTS LOADED 3kIICL TA = +25C V+ = 12V 7.5 7.0 0 5.0 2.5 120kbps 240kbps VCC = +4.5V, TA = +25C BOTH Tx OUTPUTS, LOADED 3kIICL ONE TRANSMITTER AT FULL DATA RATE ONE TRANSMITTER AT 1/8 DATA RATE 240kbps 120kbps 20kbps 0 -2.5 -5.0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) www.maximintegrated.com 1000 2000 3000 4000 LOAD CAPACITANCE (pF) MAX200-MAX213 toc03 5000 20 VCC = +5V ALL Tx OUTPUTS LOADED 3kIICL TA = +25C V+ = 12V 15 MAX209 10 +SLEW RATE MAX201 5000 0 5000 14 +SLEW RATE 20kbps 120kbps 240kbps 12 10 8 6 4 0 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) MAX202/203 TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE -SLEW RATE 20kbps 120kbps 240kbps VCC = +4.5V, TA = +25C BOTH Tx OUTPUTS, LOADED 3kIICL ONE TRANSMITTER AT FULL DATA RATE ONE TRANSMITTER AT 1/8 DATA RATE 2 0 0 116kbps 5 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 20kbps VCC = +5V ALL Tx OUTPUTS LOADED 3kIICL TA = +25C V+ = 12V 8.8 -SLEW RATE 112kbps MAX202/203 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 7.5 9.0 MAX201/MAX209 TRANSMITTER SLEW RATE vs. LOAD CAPACITANCE 25 60kbps 8.5 60kbps 9.2 8.4 5000 1000 2000 3000 4000 LOAD CAPACITANCE (pF) MAX201 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 9.5 9.4 8.6 +SLEW RATE 0 20kbps 9.6 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 5000 MAX202/203 SUPPLY CURRENT vs. LOAD CAPACITANCE 35 VCC = +4.5V, TA = +25C, BOTH Tx OUTPUTS, LOADED 3kIICL ONE TRANSMITTER AT FULL DATA RATE ONE TRANSMITTER AT 1/8 DATA RATE 30 25 240kbps MAX200-MAX213 toc08 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 10.0 -7.0 116kbps Tx SLEW RATE (V/s) 0 8 6 Tx SLEW RATE (V/s) 5.0 -SLEW RATE 10 SUPPLY CURRENT (mA) VCC = +5V ALL Tx OUTPUTS LOADED 3kIICL TA = +25C 5.4 12 MAX200-MAX213 toc04 5.6 14 9.8 MAX200-MAX213 toc05 5.8 16 MAX209 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 10.0 Tx OUTPUT VOLTAGE (IVI) 60kbps 5.2 Tx OUTPUT VOLTAGE (V) 18 6.2 6.0 VCC = +5V ALL Tx OUTPUTS LOADED 3kIICL TA = +25C 20 MAX200-MAX213 toc07 6.4 22 Tx SLEW RATE (V/s) 20kbps 6.6 MAX200-MAX213 toc06 Tx OUTPUT VOLTAGE (IVI) 6.8 MAX200-MAX213 toc01 7.0 MAX200/204/205/206/207/208/211/213 TRANSMITTER SKEW RATE vs. LOAD CAPACITANCE MAX200-MAX213 toc02 MAX200/204/205/206/207/208/211/213 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 120kbps 20 20kbps 15 5000 10 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 5000 Maxim Integrated 4 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Detailed Description 0.1F ISHDN The MAX200-MAX209/MAX211/MAX213 consist of three sections: charge-pump voltage converters, drivers (transmitters), and receivers. Each section is described in detail. +5.5V 0.1F C1+ +5V to 10V Dual Charge-Pump Voltage Converter V+ VCC 0.1F MAX200 MAX205 MAX206 MAX211 +5.5V MAX213 C1C2+ 0.1F C2- V0.1F 400k +5.5V T1 T0 T5 TIN TOUT 3k R1 T0 R5 ROUT RIN 5k EN (EN) 0V OR +5.5V DRIVE +5.5V SHDN +5.5V (0) (SHDN) Figure 1. Shutdown Current Test Circuit EN INPUT +3V 0V OUTPUT ENABLE TIME +3.5V EN INPUT RECEIVER OUTPUTS +0.8V +3V 0V OUTPUT ENABLE TIME VOH VOH - 0.1V VOL RL = 1k VOL + 0.1V The MAX201 and MAX209 include only the V+ to Vcharge pump, and are intended for applications that have a VCC = +5V supply and a V+ supply in the +9V to +13.2V range. In shutdown mode, V+ is internally connected to VCC by a 1k pulldown resistor and V- is internally connected to ground by a 1k pullup resistor. RS-232 Drivers GND NOTE 1: ( ) ARE FOR MAX213. NOTE 2: CAPACITORS CAN BE POLARIZED OR UNPOLARIZED. RECEIVER OUTPUT CL = 150pF The +5V to 10V conversion is performed by two chargepump voltage converters (Figure 4). The first uses capacitor C1 to double +5V to +10V, storing +10V on the V+ output filter capacitor, C3. The second chargepump voltage converter uses capacitor C2 to invert +10V to -10V, storing -10V on the V- output filter capacitor, C4. + 2.5V When VCC = +5V, the typical driver output-voltage swing is 8V when loaded with a nominal 5k RS-232 receiver. The output swing is guaranteed to meet the EIA/TIA-232E and V.28 specifications, which call for 5V minimum output levels under worst-case conditions. These include a minimum 3k load, VCC = +4.5V, and the maximum operating temperature. The open-circuit output-voltage swing ranges from (V+ - 0.6V) to V-. Input thresholds are both CMOS and TTL compatible. The inputs of unused drivers can be left unconnected since 400k pullup resistors to VCC are included onchip. Since all drivers invert, the pullup resistors force the outputs of unused drivers low. The input pullup resistors typically source 15A; therefore, the driver inputs should be driven high or open circuited to minimize power-supply current in shutdown mode. When in low-power shutdown mode, the driver outputs are turned off and their leakage current is less than 1mA, even if the transmitter output is backdriven between 0V and (VCC + 6V). Below -0.5V, the transmitter output is diode clamped to ground with a 1k series impedance. The transmitter output is also zener clamped to approximately (VCC + 6V), with a 1k series impedance. NOTE: POLARITY OF EN IS REVERSED FOR THE MAX213. Figure 2. Receiver Output Enable and Disable Timing www.maximintegrated.com Maxim Integrated 5 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors 0.1F 0.1F +5V +5V 0.1F 0.1F VCC C1+ V+ 0.1F C1C2+ 0.1F C2- MAX200-MAX209 MAX211 MAX213 V0.1F V+ C1C2+ MAX200-MAX209 MAX211 MAX213 V- C2- TOUT R1 T0 R5 TOUT 2500pF 7k RIN EN (EN) T1 T0 T5 TIN 3k ROUT 0.1F +5V 400k T1 T0 T5 TIN 0V (+5V) VCC 0.1F +5V 400k 0V (+5V) C1+ 0.1F R1 T0 R5 ROUT 5k 0V (+5V) 0V (+5V) SHDN (SHDN) 50pF RIN EN (EN) 5k SHDN (SHDN) MINIMUM SLEW-RATE TEST CIRCUIT MAXIMUM SLEW-RATE TEST CIRCUIT NOTE: ( ) ARE FOR MAX213. Figure 3. Transition Slew-Rate Test Circuit VCC S1 V+ V+ C1+ S2 C3 C1 I L+ S5 R L+ C2+ S6 GND C2 C4 GND S3 S4 C1- VCC GND S7 C2- S8 I L- RLV- 200kHz Figure 4. Dual Charge-Pump Diagram RS-232 Receivers The receivers convert RS-232 signals to CMOS logic output levels. Receiver outputs are inverting, maintaining compatibility with driver outputs. The guaranteed receiver input thresholds of +0.8V and +2.4V are significantly tighter than the 3.0V threshold required by the EIA/TIA232E specification. This allows receiver inputs to respond to TTL/CMOS logic levels and improves noise margin for RS-232 levels. www.maximintegrated.com The MAX200-MAX209/MAX211/MAX213 guaranteed +0.8V threshold (+0.6V in shutdown for the MAX213) ensures that receivers shorted to ground have a logic 1 output. Also, the 5k input resistance to ground ensures that a receiver with its input left open also has a logic 1 output. Receiver inputs have approximately +0.5V hysteresis. This provides clean output transitions, even with slow rise and fall time input signals with moderate amounts of noise and ringing. In shutdown, the MAX213 receivers R4 and R5 have no hysteresis. Maxim Integrated 6 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors typically to 1A (15A for the MAX213). The time required to exit shutdown is 1ms, as shown in Figure 5. All receivers except R4 and R5 on the MAX213 are put into a high-impedance state in shutdown mode. The MAX213's R4 and R5 receivers still function in shutdown mode. These two receivers are useful for monitoring external activity while maintaining minimal power consumption. TWO TRANSMITTER OUTPUTS: ONE HIGH, ONE LOW The enable control is used to put the receiver outputs into a high-impedance state, so that the receivers can be connected directly to a three-state bus. It has no effect on the RS-232 drivers or on the charge pumps. SHDN* SHUTDOWN TRANSMITTERS ON THREE TRANSMITTERS LOADED WITH 3k||2500pF. *SHUTDOWN POLARITY REVERSED FOR MAX213. MAX213 Receiver Operation in Shutdown During normal operation, the MAX213's receiver propagation delay is typically 1s. When entering shutdown with receivers active, R4 and R5 are not valid until 80s after SHDN is driven low. In shutdown mode, propagation delays increase to 4s for a high-to-low or a low-to-high transition. Figure 5. Transmitter Outputs When Exiting Shutdown Shutdown and Enable Control In shutdown mode, the MAX200/MAX205/MAX206/ MAX211/MAX213 charge pumps are turned off, V+ is pulled down to VCC, V- is pulled to ground, and the transmitter outputs are disabled. This reduces supply current When exiting shutdown, all receiver outputs are invalid until the charge pumps reach nominal values (< 2ms when using 0.1F capacitors). Table 1a. MAX200 Control Pin Configurations SHDN OPERATION STATUS TRANSMITTERS T1-T5 0 Normal Operation All Active 1 Shutdown All High-Z Table 1b. MAX205/MAX206/MAX211 Control Pin Configurations SHDN EN OPERATION STATUS TRANSMITTERS T1-T5 RECEIVERS R1-R5 0 0 Normal Operation All Active All Active 0 1 Normal Operation All Active All High-Z 1 0 Shutdown All High-Z All High-Z Table 1c. MAX213 Control Pin Configurations RECEIVERS SHDN EN OPERATION STATUS TRANSMITTERS T1-T4 0 0 Shutdown All High-Z High-Z High-Z 0 1 Shutdown All High-Z High-Z Active* 1 0 Normal Operation All Active High-Z High-Z 1 1 Normal Operation All Active Active Active R1, R2, R3 R4, R5 *Active = active with reduced performance. www.maximintegrated.com Maxim Integrated 7 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Applications Information Driver Outputs When Exiting Shutdown Capacitor Selection The type of capacitor used is not critical for proper operation. Ceramic capacitors are suggested. To ensure proper RS-232 signal levels over temperature when using 0.1F capacitors, make sure the capacitance value does not degrade excessively as the temperature varies. If in doubt, use capacitors with a larger nominal value. Also observe the capacitors' ESR value over temperature, since it influences the amount of ripple on V+ and V-. To reduce the output impedance at V+ and V-, use larger capacitors (up to 10F). If polarized capacitors are used, obey the polarities shown in Figure 1 and the pin configurations. Driving Multiple Receivers Each transmitter is designed to drive a single receiver. Transmitters can be paralleled to drive multiple receivers. Figure 5 shows two driver outputs exiting shutdown. As they become active, the two driver outputs go to opposite RS-232 levels (one driver input is high, the other is low). Each driver is loaded with 3k in parallel with 2500pF. The driver outputs display no ringing or undesirable transients as they come out of shutdown. Power-Supply Decoupling In applications that are sensitive to power-supply noise, decouple VCC to ground with a capacitor of the same value as the charge-pump capacitors. V+ and V- as Power Supplies A small amount of power can be drawn from V+ and V-, although this reduces noise margins. Power Supplies for MAX201/MAX209 If at power-up the V+ supply rises after the VCC supply, place a diode (e.g., 1N914) in series with the V+ supply. Table 2. Summary of EIA/TIA-232E, V.28 Specifications CONDITION EIA/TIA-232E, V.28 SPECIFICATION Driver Output Voltage: 0 Level PARAMETER 3k to 7k load +5.0V to +15V Driver Output Voltage: 1 Level 3k to 7k load -5.0V to -15V Output Level, Maximum Data Rate Receiver Input Voltage: 0 Level No load 25V 3k RL 7k, CL 2500pF Up to 20kbps -- +3.0V to +15V Receiver Input Voltage: 1 Level -- -3.0V to -15V Input Level, Maximum -- 25V 3k RL 7k, CL 2500pF 30V/s -- 100mA Instantaneous Slew Rate, Maximum Driver Output Short-Circuit Current, Maximum Transition Rate on Driver Output Driver Output Resistance V.28 1ms or 3% of the period EIA/TIA-232E 4% of the period -2V < VOUT < +2V 300 Table 3. DB9 Cable Connections Commonly Used for EIA/TIA-232E and V.24 Asynchronous Interfaces PIN NAME CONNECTION 1 Received Line Signal Detector, sometimes called Carrier Detect (DCD) 2 Receive Data (RD) 3 Transmit Data (TD) 4 Data Terminal Ready 5 Signal Ground 6 Data Set Ready (DSR) 7 Request to Send (RTS) Handshake from DTE 8 Clear to Send (CTS) Handshake from DCE 9 Ring Indicator Handshake from DCE www.maximintegrated.com Handshake from DCE Data from DCE Data from DTE Handshake from DTE Reference point for signals Handshake from DCE Maxim Integrated 8 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX200 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 8 0.1F +6.3V 10 11 0.1F +16V 12 7 C1+ VCC C1- +5V TO +10V VOLTAGE DOUBLER C2+ +10V TO -10V VOLTAGE INVERTER C2- V+ V- 9 0.1F +6.3V 13 0.1F +16V +5V TOP VIEW 400k 5 T1IN T3OUT 1 20 T4OUT T1OUT 2 19 T5IN T2OUT 3 18 N.C. T2IN 4 MAX200 16 T5OUT GND 6 15 T4IN VCC 7 14 T3IN C1+ 8 13 V- V+ 9 12 C2- C1- 10 11 C2+ T1OUT 2 400k 4 T2IN 17 SHND T1IN 5 T1 +5V T2 +5V T2OUT 3 400k TTL/CMOS INPUTS 14 T3IN T3 +5V T3OUT 1 RS-232 OUTPUTS 400k 15 T4IN T4 +5V DIP/SO T4OUT 20 400k 19 T5IN N.C. 18 T5 MAX200 T5OUT 16 17 SHDN GND 6 www.maximintegrated.com Maxim Integrated 9 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX201 Pin Configurations/Typical Operating Circuit +5V INPUT +9V TO +12V 0.1F 13 (15) TOP VIEW 1 C+ 1 14 V+ C- 2 13 VCC V- 3 12 GND T2OUT 4 MAX201 R2IN 5 8 T1IN DIP 1 16 V+ C- 2 15 VCC 14 GND V- 3 4 MAX201 13 T1OUT R2IN 5 R2OUT 6 11 R1OUT T2IN 7 10 T1IN N.C. 8 12 R1IN 9 SO C- N.C. V+ V- 400k (10) 8 T1IN 14 (16) 3 RS-232 OUTPUTS 400k (11) 9 R1OUT T2OUT 4 T2 R1 TTL/CMOS OUTPUTS R1IN 10 (12) RS-232 INPUTS 5k 6 R2OUT C2 0.1F +16V T1OUT 11 (13) T1 +5V TTL/CMOS INPUTS 7 T2IN C+ +12V TO -12V VOLTAGE CONVERTER +5V 9 R1OUT T2IN 7 2 C+ 11 T1OUT 10 R1IN R2OUT 6 T2OUT 0.1F +16V VCC R2 R2IN 5 5k MAX201 GND 12 (14) NOTE: PIN NUMBERS IN ( ) ARE FOR SO PACKAGE www.maximintegrated.com Maxim Integrated 10 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX202 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F +6.3V 0.1F 16 1 0.1F +6.3V 3 4 TOP VIEW 0.1F +16V C1+ 1 16 VCC V+ 2 15 GND C1- 3 14 T1OUT C2+ 4 13 R1IN C2- 5 V- 6 11 T1IN T2OUT 7 10 T2IN R2IN 8 9 MAX202 12 R1OUT 5 VCC C1+ V+ 2 +10V 6 -10V +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 0.1F +16V +5V 400k 11 T1IN +5V TTL/CMOS INPUTS DIP/SO/WIDE SO RS-232 OUTPUTS 400k 10 T2IN R2OUT T1OUT 14 T1 12 R1OUT T2OUT 7 T2 R1 R1IN 13 5k TTL/CMOS OUTPUTS 9 R2OUT R2 RS-232 INPUTS R2IN 8 5k MAX202 GND 15 www.maximintegrated.com Maxim Integrated 11 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX203 Pin Configurations/Typical Operating Circuit +5V INPUT TOP VIEW 0.1F T1IN 2 18 T2OUT MAX203 T1OUT 5 2 T1IN 16 C215 C2+ VCC 7 14 V+ C1+ 8 13 C1- GND 9 12 V- C2- 10 20 R2OUT T1IN 2 19 R2IN 18 T2OUT MAX203 17 V- T1OUT 5 16 C2- GND 6 15 C2+ VCC 7 14 C1- V+ 8 13 C1+ GND 9 12 C2+ V- 10 11 C2- SO www.maximintegrated.com RS-232 OUTPUTS 400k 1 T2IN T2OUT 18 T2 3 R1OUT R1IN 4 R1 TTL/CMOS OUTPUTS T2IN 1 R1OUT 3 T1OUT 5 T1 +5V TTL/CMOS INPUTS 11 C2+ DIP R1IN 4 400k 17 V- GND 6 VCC +5V 19 R2IN R1OUT 3 R1IN 4 7 20 R2OUT T2IN 1 5k 20 R2OUT RS-232 INPUTS R2IN 19 R2 5k DO NOT MAKE CONNECTION TO THESE PINS INTERNAL -10V POWER SUPPLY INTERNAL +10V POWER SUPPLY 8 (13) 13 (14) 12 (10) 17 14 (8) C1+ C2+ C1- C2+ MAX203 V- C2C2- VV+ GND 6 11 (12) 15 16 10 (11) GND 9 NOTE: PIN NUMBERS IN ( ) ARE FOR SO PACKAGE. Maxim Integrated 12 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX204 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 7 0.1F +6.3V 9 10 0.1F +16V 11 6 C1+ VCC C1- +5V TO +10V VOLTAGE DOUBLER C2+ +10V TO -10V VOLTAGE INVERTER C2- V+ V- 8 0.1F +6.3V 12 0.1F +16V +5V TOP VIEW T1OUT 1 16 T3OUT T2OUT 2 15 T4OUT T2IN 3 14 T4IN T1IN 4 GND 5 MAX204 400k 4 T1IN +5V 13 T3IN 400k 3 T2IN 12 V- VCC 6 11 C2- C1+ 7 10 C2+ V+ 8 9 C1- T1OUT 1 T1 TTL/CMOS INPUTS T2OUT 2 T2 +5V RS-232 OUTPUTS 400k 13 T3IN DIP/SO T3OUT 16 T3 +5V 400k 14 T4IN T4OUT 15 T4 MAX204 GND 5 www.maximintegrated.com Maxim Integrated 13 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX205 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 12 VCC +5V 400k 8 T1IN T1OUT 3 T1 +5V 400k 7 T2IN T2OUT 4 T2 +5V 400k TTL/CMOS INPUTS 15 T3IN TOP VIEW T3OUT 2 T3 +5V RS-232 OUTPUTS 400k T4OUT 1 24 R3IN T3OUT 2 23 R3OUT T1OUT 3 22 T5IN T2OUT 4 MAX205 5 20 EN R2OUT 6 19 T5OUT T2IN 7 18 R4IN T1IN 8 17 R4OUT R1OUT 9 16 T4IN R1IN 10 15 T3IN GND 11 14 R5OUT VCC 12 13 R5IN T4OUT 1 T4 +5V 400k 21 SHDN R2IN DIP 16 T4IN 22 T5IN 9 R1OUT T5OUT 19 T5 R1 R1IN 10 5k 6 R2OUT R2 R2IN 5 5k TTL/CMOS OUTPUTS 23 R3OUT R3 R3IN 24 RS-232 INPUTS 5k 17 R4OUT R4 R4IN 18 5k 14 R5OUT R5 R5IN 13 5k 20 EN MAX205 SHDN 21 GND 11 www.maximintegrated.com Maxim Integrated 14 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX206 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 9 10 0.1F +6.3V 12 13 0.1F +16V 14 VCC C1+ V+ +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 11 0.1F +6.3V 15 0.1F +16V +5V TOP VIEW 400k T3OUT 1 24 T4OUT T1OUT 2 22 R2OUT MAX206 R1OUT 5 400k 21 SHDN 6 T2IN 20 EN T2IN 6 19 T4IN T1IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ T1OUT 2 T1 +5V 23 R2IN T2OUT 3 R1IN 4 7 T1IN +5V TTL/CMOS INPUTS T2OUT 3 T2 RS-232 OUTPUTS 400k 18 T3IN T3OUT 1 T3 +5V 400k 19 T4IN DIP/SO 5 R1OUT T4OUT 24 T4 R1 R1IN 4 5k TTL/CMOS OUTPUTS 22 R2OUT R2 R2IN 23 RS-232 INPUTS 5k 17 R3OUT R3 R3IN 16 5k 20 EN SHDN 21 MAX206 GND 8 www.maximintegrated.com Maxim Integrated 15 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX207 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 9 10 0.1F +6.3V 12 13 0.1F +16V 14 C1+ VCC C1- +5V TO +10V VOLTAGE DOUBLER C2+ V+ +10V TO -10V VOLTAGE INVERTER C2- V- 11 0.1F +6.3V 15 0.1F +16V +5V 400k 7 T1IN TOP VIEW T1OUT 2 T1 +5V 400k T3OUT 1 24 T4OUT T1OUT 2 23 R2IN T2OUT 3 R1IN 4 6 T2IN T2OUT 3 T2 +5V 22 R2OUT MAX207 R1OUT 5 20 T5OUT T2IN 6 19 T4IN T1IN 7 18 T3IN GND 8 17 R3OUT VCC 9 16 R3IN C1+ 10 15 V- V+ 11 14 C2- C1- 12 400k 21 T5IN TTL/CMOS INPUTS 18 T3IN T3OUT 1 T3 +5V RS-232 OUTPUTS 400k 19 T4IN T4OUT 24 T4 +5V 400k 21 T5IN 13 C2+ T5OUT 20 T5 DIP/SO/SSOP 5 R1OUT R1 R1IN 4 5k TTL/CMOS OUTPUTS 22 R2OUT R2 R2IN 23 RS-232 INPUTS 5k 17 R3OUT R3 R3IN 16 5k MAX207 GND 8 www.maximintegrated.com Maxim Integrated 16 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX208 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 9 10 0.1F +6.3V 12 13 0.1F +16V 14 VCC C1+ V+ 11 0.1F +6.3V +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 15 0.1F +16V +5V 400k 5 T1IN TOP VIEW T2OUT 1 24 T3OUT T1OUT 2 23 R3IN R2IN 3 R2OUT 4 22 R3OUT MAX208 T1IN 5 21 T4IN 400k 18 T2IN TTL/CMOS INPUTS 19 T3IN R1IN 7 18 T2IN GND 8 17 R4OUT VCC 9 16 R4IN C1+ 10 15 V- V+ 11 14 C2- C1- 12 13 C2+ T2OUT 1 T2 +5V 20 T4OUT R1OUT 6 T1OUT 2 T1 +5V RS-232 OUTPUTS 400k 19 T3IN T3OUT 24 T3 +5V 400k 21 T4IN T4OUT 20 T4 6 R1OUT R1 R1IN 7 5k DIP/SO 4 R2OUT R2 R2IN 3 5k TTL/CMOS OUTPUTS 22 R3OUT R3 RS-232 INPUTS R3IN 23 5k 17 R4OUT R4 R4IN 16 5k MAX208 GND 8 www.maximintegrated.com Maxim Integrated 17 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX209 Pin Configuration/Typical Operating Circuit +5V INPUT 9V - 13.2V INPUT 0.1F 6 0.1F +16V 7 C+ 4 5 VCC V+ 8 +10V TO +10V VOLTAGE INVERTER C- 0.1F +16V +5V TOP VIEW 400k R1OUT 1 24 T1IN R1IN 2 23 T2IN T1OUT 19 T1 +5V 22 R2OUT GND 3 VCC 4 24 T1IN MAX209 V+ 5 20 T2OUT C+ 6 19 T1OUT C- 7 18 R3IN V- 8 17 R3OUT R5IN 9 16 T3IN R5OUT 10 15 N.C. R4OUT 11 14 EN R4IN 12 400k 21 R2IN TTL/CMOS INPUTS 23 T2IN T2OUT 20 T2 +5V RS-232 OUTPUTS 400k 16 T3IN 1 R1OUT T3OUT 13 T3 R1 13 T3OUT R1IN 2 5k DIP/SO 22 R2OUT R2 R2IN 21 5k TTL/CMOS OUTPUTS 17 R3OUT R3 R3IN 18 RS-232 INPUTS 5k 11 R4OUT R4 R4IN 12 5k 10 R5OUT R5 R5IN 9 5k 14 EN MAX209 GND N.C. 15 3 www.maximintegrated.com Maxim Integrated 18 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX211 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 11 12 0.1F +6.3V 14 15 0.1F +16V 16 VCC C1+ C1C2+ C2- +5V TO +10V VOLTAGE DOUBLER V+ +10V TO -10V VOLTAGE INVERTER V- 13 0.1F +6.3V 17 0.1F +16V +5V 400k 7 T1IN TOP VIEW T1OUT 2 T1 +5V 400k T3OUT 1 28 T4OUT T1OUT 2 27 R3IN T2OUT 3 26 R3OUT R2IN 4 25 SHDN R2OUT 5 T2IN 6 T1IN 7 22 R4OUT R1OUT 8 21 T4IN R1IN 9 20 T3IN MAX211 6 T2IN TTL/CMOS INPUTS 19 R5OUT VCC 11 18 R5IN C1+ 12 17 V- V+ 13 16 C2- C1- 14 15 C2+ T3OUT 1 T3 +5V 23 R4IN GND 10 RS-232 OUTPUTS 400k 20 T3IN 24 EN T2OUT 3 T2 +5V 400k 21 T4IN 8 R1OUT T4OUT 28 T4 R1 R1IN 9 5k 5 R2OUT R2 SO/SSOP R2IN 4 5k TTL/CMOS OUTPUTS 26 R3OUT R3 R3IN 27 RS-232 INPUTS 5k 22 R4OUT R4 R4IN 23 5k 19 R5OUT R5 R5IN 18 5k 24 EN MAX211 SHDN 25 GND 10 www.maximintegrated.com Maxim Integrated 19 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors MAX213 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1F 11 12 0.1F +6.3V 14 15 0.1F +16V 16 VCC C1+ V+ +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 13 0.1F +6.3V 17 0.1F +16V +5V 400k 7 T1IN T1OUT 2 T1 +5V 400k TOP VIEW 6 T2IN T3OUT 1 28 T4OUT T1OUT 2 27 R3IN T2OUT 3 26 R3OUT R2IN 4 25 SHDN R2OUT 5 T2IN 6 T1IN 7 22 R4OUT* R1OUT 8 21 T4IN R1IN 9 20 T3IN MAX213 RS-232 OUTPUTS 400k 20 T3IN T3OUT 1 T3 +5V 24 EN 400k 23 R4IN* GND 10 19 R5OUT* VCC 11 18 R5IN* C1+ 12 17 V- V+ 13 16 C2- C1- 14 15 C2+ SO/SSOP TTL/CMOS INPUTS T2OUT 3 T2 +5V 21 T4IN 8 R1OUT T4OUT 28 T4 R1 R1IN 9 5k 5 R2OUT R2 R2IN 4 5k TTL/CMOS OUTPUTS 26 R3OUT R3 R3IN 27 RS-232 INPUTS 5k 22 R4OUT* R4 R4IN* 23 5k 19 R5OUT* R5 R5IN* 18 5k 24 EN MAX213 SHDN 25 GND *ACTIVE IN SHUTDOWN www.maximintegrated.com 10 Maxim Integrated 20 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Ordering Information PART MAX200CPP TEMP RANGE PIN-PACKAGE PART TEMP RANGE PIN-PACKAGE 0C to +70C 20 Plastic DIP MAX206EWG -40C to +85C 24 Wide SO MAX200CWP 0C to +70C 20 Wide SO MAX206EAG -40C to +85C 24 SSOP MAX200EPP -40C to +85C 20 Plastic DIP MAX207CNG 0C to +70C 24 Narrow Plastic DIP MAX200EWP -40C to +85C 20 Wide SO MAX207CWG 0C to +70C 24 Wide SO MAX201CPD 0C to +70C 14 Plastic DIP MAX207CAG 0C to +70C 24 SSOP MAX201CWE 0C to +70C 16 Wide SO MAX207ENG -40C to +85C 24 Narrow Plastic DIP MAX201C/D 0C to +70C Dice* MAX207EWG -40C to +85C 24 Wide SO MAX201EPD -40C to +85C 14 Plastic DIP MAX207EAG -40C to +85C 24 SSOP MAX201EWE -40C to +85C 16 Wide SO MAX208CNG 0C to +70C 24 Narrow Plastic DIP MAX202CPE 0C to +70C 16 Plastic DIP MAX208CWG 0C to +70C 24 Wide SO MAX202CSE 0C to +70C 16 Narrow SO MAX208CAG 0C to +70C 24 SSOP MAX202CWE 0C to +70C 16 Wide SO MAX208C/D 0C to +70C Dice* MAX202C/D 0C to +70C Dice* MAX208ENG -40C to +85C 24 Narrow Plastic DIP MAX202EPE -40C to +85C 16 Plastic DIP MAX208EWG -40C to +85C 24 Wide SO MAX202ESE -40C to +85C 16 Narrow SO MAX208EAG -40C to +85C 24 SSOP MAX202EWE -40C to +85C 16 Wide SO MAX209CNG 0C to +70C 24 Narrow Plastic DIP MAX203CPP 0C to +70C 20 Plastic DIP MAX209CWG 0C to +70C 24 Wide SO MAX203CWP 0C to +70C 20 Wide SO MAX209C/D 0C to +70C Dice* MAX203EPP -40C to +85C 20 Plastic DIP MAX209ENG -40C to +85C 24 Narrow Plastic DIP MAX203EWP -40C to +85C 20 Wide SO MAX209EWG -40C to +85C 24 Wide SO MAX204CPE 0C to +70C 16 Plastic DIP MAX211CWI 0C to +70C 28 Wide SO MAX204CWE 0C to +70C 16 Wide SO MAX211CAI 0C to +70C 28 SSOP MAX204C/D 0C to +70C Dice* MAX211C/D 0C to +70C Dice* MAX204EPE -40C to +85C 16 Plastic DIP MAX211EWI -40C to +85C 28 Wide SO MAX204EWE -40C to +85C 16 Wide SO MAX211EAI -40C to +85C 28 SSOP MAX205CPG 0C to +70C 24 Wide Plastic DIP MAX213CWI 0C to +70C 28 Wide SO MAX205EPG -40C to +85C 24 Wide Plastic DIP MAX213CAI 0C to +70C 28 SSOP MAX206CNG 0C to +70C 24 Narrow Plastic DIP MAX213C/D 0C to +70C Dice* MAX206CWG 0C to +70C 24 Wide SO MAX213EWI -40C to +85C 28 Wide SO MAX206CAG 0C to +70C 24 SSOP MAX213EAI -40C to +85C 28 SSOP MAX206ENG -40C to +85C www.maximintegrated.com 24 Narrow Plastic DIP *Contact factory for dice specifications. Maxim Integrated 21 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Selector Guide (continued) PART POWER-SUPPLY VOLTAGE (V) NUMBER OF RS-232 DRIVERS NUMBER OF RS-232 RECEIVERS NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN NUMBER OF EXTERNAL CAPACITORS (0.1F) MAX204 +5 4 0 0 4 No/No MAX205 +5 5 5 0 None Yes/Yes MAX206 +5 4 3 0 4 Yes/Yes MAX207 +5 5 3 0 4 No/No MAX208 +5 4 4 0 4 No/No MAX209 +5 and +9.0 to +13.2 3 5 0 2 No/Yes MAX211 +5 4 5 0 4 Yes/Yes MAX213 +5 4 5 2 4 Yes/Yes LOW-POWER SHUTDOWN/TTL THREE-STATE Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 14 CDIP J14-3 21-0045 16 CDIP J16-3 21-0045 20 CDIP J20-2 21-0045 24 CDIP R24-4 21-0045 14 PDIP P14-3 21-0043 16 PDIP P16-1 21-0043 20 PDIP P20-3 21-0043 24 PDIP N24-2 21-0043 24 PDIP N24-3 21-0043 24 PDIP P24-1 21-0044 24 PDIP P24M-1 21-0044 16 SO S16-3 21-0041 16 SO W16-3 21-0042 16 SO W16-1 21-0042 20 SO W20M-1 21-0042 20 SO W20-3 21-0042 24 SO W24-2 21-0042 28 SO W28-1 21-0042 28 SO W28-2 21-0042 24 SSOP A24-3 21-0056 24 SSOP A24-2 21-0056 28 SSOP A28-1 21-0056 16 TSSOP U16-1 21-0066 www.maximintegrated.com Maxim Integrated 22 MAX200-MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1F External Capacitors Revision History REVISION NUMBER REVISION DATE 6 10/03 7 8 PAGES CHANGED DESCRIPTION Changed the Features section and section information to the Next-Generation Device Features section. 1 12/05 Added Note 1 to the Absolute Maximum Ratings section. 2 1/15 Updated page 1 content 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2015 Maxim Integrated Products, Inc. 23 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX201CWE+ MAX202CPE+ MAX202CSE+ MAX202CWE+ MAX202EPE+ MAX202ESE+ MAX202EWE+ MAX203CPP+G36 MAX203CWP+G36 MAX204CPE+ MAX205CPG+G36 MAX206CWG+ MAX207CAG+ MAX207CNG+ MAX207CWG+ MAX208CAG+ MAX208CNG+ MAX208CWG+ MAX211CAI+ MAX211CWI+ MAX213CAI+ MAX213CWI+ MAX213EAI+ MAX4566ESE+T MAX200CWP+ MAX200CWP+T MAX200EWP+ MAX200EWP+T MAX201CPD+ MAX201CWE+T MAX201EPD+ MAX201EWE+ MAX201EWE+T MAX202CSE+T MAX202CUE+ MAX202CUE+T MAX202CWE+T MAX202ESE+T MAX202EUE+ MAX202EWE+T MAX203CPP MAX203CWP+G104 MAX203CWP+TG104 MAX203CWP+TG36 MAX204CWE+ MAX204CWE+T MAX204EWE+ MAX204EWE+T MAX206CAG+ MAX206CAG+T MAX206CNG+ MAX206CWG+T MAX206EAG+ MAX206EAG+T MAX206EWG+ MAX206EWG+T MAX207CAG+T MAX208CAG+T MAX208CWG+T MAX209CNG+ MAX209CWG+ MAX209CWG+T MAX209ENG+ MAX209EWG+T MAX211CAI+T MAX211CWI+T MAX211EAI+ MAX211EAI+T MAX211EWI+ MAX211EWI+T MAX213CAI+T MAX213CWI+T MAX213EAI+T MAX213EEWI+ MAX213EWI+ MAX213EWI+T MAX207CWG+T