530BC326M000DG - Silicon Labs

Si530/531

CRYSTAL OSCILLATOR (XO)

(10 MHZ TO 1.4 GHZ)

Features

Applications

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL

circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

Functional Block Diagram

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL® with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL®

Clock

Synthesis

VDD CLK+CLK–

OE GND

Ordering Information:

See page 7.

Pin Assignments:

See page 6.

(Top View)

Si5602

4GND

VDD

CLK+

CLK–

4GND

VDD

CLK

4GND

VDD

CLK+

CLK–

Si530 (LVDS/LVPECL/CML)

Si530 (CMOS)

Si531 (LVDS/LVPECL/CML)

REVISION D

Si530/531

2 Rev. 1.1

1. Electrical Specifications

Table 1. Recommended Operating Conditions

Parameter Symbol Test Condition Min Typ Max Units

Supply Voltage1VDD 3.3 V option 2.97 3.3 3.63

V2.5 V option 2.25 2.5 2.75

1.8 V option 1.71 1.8 1.89

Supply Current IDD Output enabled

LVPECL

CML

LVDS

CMOS

—

111

121

108

Tristate mode — 60 75

Output Enable (OE)2VIH 0.75 x VDD ——

VIL ——0.5

Operating Temperature Range TA–40 — 85 ºC

Notes:

1. Selectable parameter specified by part number. See Section 3. "Ordering Information" on page 7 for further details.

2. OE pin includes a 17 kΩ pullup resistor to VDD.

Table 2. CLK± Output Frequency Characteristics

Parameter Symbol Test Condition Min Typ Max Units

Nominal Frequency1,2 fOLVPECL/LVDS/CML 10 — 945

MHz

CMOS 10 — 160

Initial Accuracy fi

Measured at +25 °C at time of

shipping — ±1.5 — ppm

Temperature Stability1,3

–7

–20

–50

—

+20

+50

ppm

Aging fa

Frequency drift over first year — — ±3 ppm

Frequency drift over 15 year

life — — ±10 ppm

Notes:

1. See Section 3. "Ordering Information" on page 7 for further details.

2. Specified at time of order by part number. Also available in frequencies from 970 to 1134 MHz and 1213 to 1417 MHz.

3. Selectable parameter specified by part number.

4. Time from powerup or tristate mode to fO.

Si530/531

Rev. 1.1 3

Total Stability

Temp stability = ±7 ppm — — ±20 ppm

Temp stability = ±20 ppm — — ±31.5 ppm

Temp stability = ±50 ppm — — ±61.5 ppm

Powerup Time4tOSC ——10ms

Table 3. CLK± Output Levels and Symmetry

Parameter Symbol Test Condition Min Typ Max Units

LVPECL Output Option1VOmid-level VDD – 1.42 — VDD – 1.25 V

VOD swing (diff) 1.1 —1.9 VPP

VSE swing (single-ended) 0.55 —0.95 VPP

LVDS Output Option2VOmid-level 1.125 1.20 1.275 V

VOD swing (diff) 0.5 0.7 0.9 VPP

CML Output Option2VOmid-level — VDD – 0.75 — V

VOD swing (diff) 0.70 0.95 1.20 VPP

CMOS Output Option3VOH IOH =32mA 0.8 x VDD —VDD V

VOL IOL =32mA — — 0.4

Rise/Fall time (20/80%) tR, tFLVPECL/LVDS/CML — — 350 ps

CMOS with CL=15pF — 1 — ns

Symmetry (duty cycle) SYM LVPECL: VDD – 1.3 V (diff)

LVDS: 1.25 V (diff)

CMOS: VDD/2

45 — 55 %

Notes:

1. 50 Ω to VDD – 2.0 V.

2. Rterm = 100 Ω (differential).

3. CL = 15 pF

Table 2. CLK± Output Frequency Characteristics (Continued)

Parameter Symbol Test Condition Min Typ Max Units

Notes:

1. See Section 3. "Ordering Information" on page 7 for further details.

2. Specified at time of order by part number. Also available in frequencies from 970 to 1134 MHz and 1213 to 1417 MHz.

3. Selectable parameter specified by part number.

4. Time from powerup or tristate mode to fO.

Si530/531

4 Rev. 1.1

Table 4. CLK± Output Phase Jitter

Parameter Symbol Test Condition Min Typ Max Units

Phase Jitter (RMS)*

for FOUT > 500 MHz

φJ12 kHz to 20 MHz (OC-48) — 0.25 0.40 ps

50 kHz to 80 MHz (OC-192) — 0.26 0.37

Phase Jitter (RMS)*

for FOUT of 125 to 500 MHz

φJ12 kHz to 20 MHz (OC-48) — 0.36 0.50 ps

50 kHz to 20 MHz (OC-192) — 0.34 0.42

*Note: Differential Modes: LVPECL/LVDS/CML. Refer to AN256 for further information.

Table 5. CLK± Output Period Jitter

Parameter Symbol Test Condition Min Typ Max Units

Period Jitter* JPER RMS — 2 — ps

Peak-to-Peak — 14 —

*Note: Any output mode, including CMOS, LVPECL, LVDS, CML. N = 1000 cycles. Refer to AN279 for further information.

Table 6. CLK± Output Phase Noise (Typical)

Offset Frequency (f) 120.00 MHz

LVDS

156.25 MHz

LVPECL

622.08 MHz

LVPECL

Units

100 Hz

1kHz

10 kHz

100 kHz

1MHz

10 MHz

100 MHz

–112

–122

–132

–137

–144

–150

n/a

–105

–122

–128

–135

–144

–147

n/a

–97

–107

–116

–121

–134

–146

–148

dBc/Hz

Si530/531

Rev. 1.1 5

Table 7. Absolute Maximum Ratings1

Parameter Symbol Rating Units

Maximum Operating Temperature TAMAX 85 ºC

Supply Voltage VDD –0.5 to +3.8 Volts

Input Voltage (any input pin) VI–0.5 to VDD + 0.3 Volts

Storage Temperature TS–55 to +125 ºC

ESD Sensitivity (HBM, per JESD22-A114) ESD 2500 Volts

Soldering Temperature (Pb-free profile)2TPEAK 260 ºC

Soldering Temperature Time @ TPEAK (Pb-free profile)2tP20–40 seconds

Notes:

1. Stresses beyond those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional

operation or specification compliance is not implied at these conditions. Exposure to maximum rating conditions for

extended periods may affect device reliability.

2. The device is compliant with JEDEC J-STD-020C. Refer to Si5xx Packaging FAQ available for download at

www.silabs.com/VCXO for further information, including soldering profiles.

Table 8. Environmental Compliance

The Si530/531 meets the following qualification test requirements.

Parameter Conditions/Test Method

Mechanical Shock MIL-STD-883F, Method 2002.3 B

Mechanical Vibration MIL-STD-883F, Method 2007.3 A

Solderability MIL-STD-883F, Method 203.8

Gross & Fine Leak MIL-STD-883F, Method 1014.7

Resistance to Solvents MIL-STD-883F, Method 2016

Si530/531

6 Rev. 1.1

2. Pin Descriptions

Table 9. Pinout for Si530 Series

Pin Symbol LVDS/LVPECL/CML Function CMOS Function

1 OE (CMOS only)* No connection

Output enable

0 = clock output disabled (outputs tristated)

1 = clock output enabled

(LVPECL,LVDS,

CML)*

Output enable

0 = clock output disabled (outputs tristated)

1 = clock output enabled

No connection

3 GND Electrical and Case Ground Electrical and Case Ground

4 CLK+ Oscillator Output Oscillator Output

5 CLK– Complementary Output No connection

DD Power Supply Voltage Power Supply Voltage

*Note: OE includes a 17 kΩ pullup resistor to VDD.

Table 10. Pinout for Si531 Series

Pin Symbol LVDS/LVPECL/CML Function

1 OE (LVPECL, LVDS, CML)*

Output enable

0 = clock output disabled (outputs tristated)

1 = clock output enabled

2 No connection No connection

3 GND Electrical and Case Ground

4 CLK+ Oscillator Output

5 CLK– Complementary output

DD Power Supply Voltage

*Note: OE includes a 17 kΩ pullup resistor to VDD.

4GND

VDD

CLK

(Top View)

4GND

VDD

CLK+

CLK–

NC 1

4GND

VDD

CLK+

CLK–

Si530

LVDS/LVPECL/CML

Si530

CMOS

Si531

LVDS/LVPECL/CML

Si530/531

Rev. 1.1 7

3. Ordering Information

The Si530/531 XO supports a variety of options including frequency, temperature stability, output format, and VDD.

Specific device configurations are programmed into the Si530/531 at time of shipment. Configurations can be

specified using the Part Number Configuration chart below. Silicon Laboratories provides a web browser-based

part number configuration utility to simplify this process. Refer to www.silabs.com/VCXOPartNumber to access this

tool and for further ordering instructions. The Si530 and Si531 XO series are supplied in an industry-standard,

RoHS compliant, 6-pad, 5 x 7 mm package. The Si531 Series supports an alternate OE pinout (pin #1) for the

LVPECL, LVDS, and CML output formats. See Tables 9 and 10 for the pinout differences between the Si530 and

Si531 series.

Figure 1. Part Number Convention

53x XXXXMXXX

1st Option Code

VDD Output Format Output Enable Polarity

A 3.3 LVPECL High

B 3.3 LVDS High

C3.3CMOS High

D3.3CML High

E 2.5 LVPECL High

F 2.5 LVDS High

G2.5CMOS High

H2.5CML High

J 1.8 CMOS High

K1.8CML High

M 3.3 LVPECL Low

N 3.3 LVDS Low

P 3.3 CMOS Low

Q 3.3 CML Low

R 2.5 LVPECL Low

S 2.5 LVDS Low

T 2.5 CMOS Low

U 2.5 CML Low

V 1.8 CMOS Low

W 1.8 CML Low

Note:

CMOS available to 160 MHz.

DG R

Frequency (e.g., 622M080 is 622.080 MHz)

Available frequency range is 10 to 945 MHz, 970 to 1134 MHz, and

1213 to 1417 MHz. The position of “M” shifts to denote higher or lower

frequencies. If the frequency of interest requires greater than 6 digit

resolution, a six digit code will be assigned for the specific frequency.

Tape & Reel Packaging

Blank = Trays

Operating Temp Range (°C)

G -40 to +85°C

Part Revision Letter

530 or 531 XO

Product Family

Example P/N: 530AB622M080DGR is a 5 x 7 XO in a 6 pad package. The frequency is 622.080 MHz, with a 3.3 V supply, LVPECL output,

and Output Enable active high polarity. Temperature stability is specifed as ±20 ppm. The part is specified for –40 to +85 °C ambient

temperature range operation and is shipped in tape and reel format.

2nd Option Code

Code Temperature Stability (ppm, max, ±) Total Stablility (ppm, max, ±)

A 50 61.5

B 20 31.5

C 7 20

Si530/531

8 Rev. 1.1

4. Outline Diagram and Suggested Pad Layout

Figure 2 illustrates the package details for the Si530/531. Table 11 lists the values for the dimensions shown in the

illustration.

Figure 2. Si530/531 Outline Diagram

Table 11. Package Diagram Dimensions (mm)

Dimension Min Nom Max

A 1.45 1.65 1.85

b1.21.41.6

c0.60 TYP.

D 7.00 BSC.

D1 6.10 6.2 6.30

e 2.54 BSC.

E 5.00 BSC.

E1 4.30 4.40 4.50

L 1.07 1.27 1.47

S 1.815 BSC.

R 0.7 REF.

aaa — — 0.15

bbb — — 0.15

ccc — — 0.10

ddd — — 0.10

Si530/531

Rev. 1.1 9

5. Si530/Si531 Mark Specification

Figure 3 illustrates the mark specification for the Si530/Si531. Table 12 lists the line information.

Figure 3. Mark Specification

Table 12. Si53x Top Mark Description

Line Position Description

1 1–10 “SiLabs”+ Part Family Number, 5xx (First 3 characters in part number)

2 1–10 Si530, Si531: Option1 + Option2 + Freq(7) + Temp

Si532, Si533, Si534, Si530/Si531 w/ 8-digit resolution:

Option1 + Option2 + ConfigNum(6) + Temp

3 Trace Code

Position 1 Pin 1 orientation mark (dot)

Position 2 Product Revision (D)

Position 3–6 Tiny Trace Code (4 alphanumeric characters per assembly release instructions)

Position 7 Year (least significant year digit), to be assigned by assembly site (ex: 2007 = 7)

Position 8–9 Calendar Work Week number (1–53), to be assigned by assembly site

Position 10 “+” to indicate Pb-Free and RoHS-compliant

SiLabs 123

123

R T T T T Y W W +

1 2 3 4 5 6 7 8 9 0

Si530/531

10 Rev. 1.1

6. 6-Pin PCB Land Pattern

Figure 4 illustrates the 6-pin PCB land pattern for the Si530/531. Table 13 lists the values for the dimensions shown

in the illustration.

Figure 4. Si530/531 PCB Land Pattern

Table 13. PCB Land Pattern Dimensions (mm)

Dimension Min Max

D2 5.08 REF

e 2.54 BSC

E2 4.15 REF

GD 0.84 —

GE 2.00 —

VD 8.20 REF

VE 7.30 REF

X1.70 TYP

Y2.15 REF

ZD — 6.78

ZE — 6.30

Notes:

1. Dimensioning and tolerancing per the ANSI Y14.5M-1994 specification.

2. Land pattern design based on IPC-7351 guidelines.

3. All dimensions shown are at maximum material condition (MMC).

4. Controlling dimension is in millimeters (mm).

Si530/531

Rev. 1.1 11

DOCUMENT CHANGE LIST

Revision 0.4 to Revision 0.5

Updated Table 1, “Recommended Operating

Conditions,” on page 2.

 Added maximum supply current specifications.

 Specified relationship between temperature at startup

and operation temperature.

Updated Table 4, “CLK± Output Phase Jitter,” on

page 4 to include maximum rms jitter generation

specifications and updated typical rms jitter

specifications.

Added Table 6, “CLK± Output Phase Noise

(Typical),” on page 4.

Added Output Enable active polarity as an option in

Figure 1, “Part Number Convention,” on page 7.

Revision 0.5 to Revision 1.0

Updated Note 3 in Table 1, “Recommended

Operating Conditions,” on page 2.

Updated Figure 1, “Part Number Convention,” on

page 7.

Revision 1.0 to Revision 1.1

Updated Table 1, “Recommended Operating

Conditions,” on page 2.

 Device maintains stable operation over –40 to +85 ºC

operating temperature range.

 Supply current specifications updated for revision D.

Updated Table 2, “CLK± Output Frequency

Characteristics,” on page 2.

 Added specification for ±20 ppm lifetime stability

(±7 ppm temperature stability) XO.

Updated Table 3, “CLK± Output Levels and

Symmetry,” on page 3.

 Updated LVDS differential peak-peak swing

specifications.

Updated Table 4, “CLK± Output Phase Jitter,” on

page 4.

Updated Table 5, “CLK± Output Period Jitter,” on

page 4.

 Revised period jitter specifications.

Updated Table 7, “Absolute Maximum Ratings1,” on

page 5 to reflect the soldering temperature time at

260 ºC is 20–40 sec per JEDEC J-STD-020C.

Updated 3. "Ordering Information" on page 7.

 Changed ordering instructions to revision D.

Added 5. "Si530/Si531 Mark Specification" on page

Si530/531

12 Rev. 1.1

CONTACT INFORMATION

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

Tel: 1+(512) 416-8500

Fax: 1+(512) 416-9669

Toll Free: 1+(877) 444-3032

Email: VCXOinfo@silabs.com

Internet: www.silabs.com

Silicon Laboratories, Silicon Labs, and DSPLL are trademarks of Silicon Laboratories Inc.

Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders.

The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.

Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from

the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features

or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, rep-

resentation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation conse-

quential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to

support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where per-

sonal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap-

plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages.