SCLS085C - DECEMBER 1982 - REVISED NOVEMBER 2002 D Wide Operating Voltage Range of 2 V to 6 V D Outputs Can Drive Up to 10 LSTTL Loads D Low Power Consumption, 20-A Max ICC D Typical tpd = 11 ns D 4-mA Output Drive at 5 V D Low Input Current of 1 A Max SN54HC14 . . . J OR W PACKAGE SN74HC14 . . . D, DB, N, NS, OR PW PACKAGE (TOP VIEW) 1 14 2 13 3 12 4 11 5 10 6 9 7 8 1Y 1A NC VCC 6A VCC 6A 6Y 5A 5Y 4A 4Y 2A NC 2Y NC 3A 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 6Y NC 5A NC 5Y 3Y GND NC 4Y 4A 1A 1Y 2A 2Y 3A 3Y GND SN54HC14 . . . FK PACKAGE (TOP VIEW) NC - No internal connection description/ordering information These Schmitt-trigger devices contain six independent inverters. They perform the Boolean function Y = A in positive logic. ORDERING INFORMATION PDIP - N SN74HC14N Tube SN74HC14D Tape and reel SN74HC14DR SOP - NS Tape and reel SN74HC14NSR HC14 SSOP - DB Tape and reel SN74HC14DBR HC14 Tube SN74HC14PW Tape and reel SN74HC14PWR CDIP - J Tube SNJ54HC14J SNJ54HC14J CFP - W Tube SNJ54HC14W SNJ54HC14W TSSOP - PW -55C 125C 55 C to 125 C TOP-SIDE MARKING Tube SOIC - D -40C 40 C to 85C 85 C ORDERABLE PART NUMBER PACKAGE TA SN74HC14N HC14 HC14 LCCC - FK Tube SNJ54HC14FK SNJ54HC14FK Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each inverter) INPUT A OUTPUT Y H L L H Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated ! "#$ ! %#&'" ( $) (#" ! " !%$"" ! %$ *$ $! $+! ! #$ ! ! (( , -) (#" %"$!!. ($! $"$!!'- "'#($ $! . '' %$ $!) %(#" ! "%' /0121 '' %$ $! $ $! $( #'$!! *$,!$ $() '' *$ %(#" ! %(#" %"$!!. ($! $"$!!'- "'#($ $! . '' %$ $!) POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SCLS085C - DECEMBER 1982 - REVISED NOVEMBER 2002 logic diagram (positive logic) A Y absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 3) SN54HC14 UNIT NOM MAX MIN NOM MAX 2 5 6 2 5 6 V 1.8 V VCC VCC V VCC VIL Supply voltage VI VO Input voltage 0 Output voltage 0 Low-level input voltage SN74HC14 MIN VCC = 6 V 1.8 VCC VCC 0 0 V TA Operating free-air temperature -55 125 -40 85 C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCLS085C - DECEMBER 1982 - REVISED NOVEMBER 2002 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VCC VT+ VT- MIN MAX MAX 2V 0.7 1.2 1.5 0.7 1.5 0.7 1.5 4.5 V 1.55 2.5 3.15 1.55 3.15 1.55 3.15 6V 2.1 3.3 4.2 2.1 4.2 2.1 4.2 2V 0.3 0.6 1 0.3 1 0.3 1 4.5 V 0.9 1.6 2.45 0.9 2.45 0.9 2.45 6V 1.2 2 3.2 1.2 3.2 1.2 3.2 UNIT V V 0.6 1.2 0.2 1.2 0.2 1.2 0.4 0.9 2.1 0.4 2.1 0.4 2.1 6V 0.5 1.3 2.5 0.5 2.5 0.5 2.5 2V 1.9 1.998 1.9 1.9 IOH = -20 20 A 4.5 V 4.4 4.499 4.4 4.4 6V 5.9 5.999 5.9 5.9 IOH = -4 mA IOH = -5.2 mA 4.5 V 3.98 4.3 3.7 3.84 6V 5.48 5.8 5.2 5.34 2V 0.002 0.1 0.1 0.1 IOL = 20 A 4.5 V 0.001 0.1 0.1 0.1 6V 0.001 0.1 0.1 0.1 4.5 V 0.17 0.26 0.4 0.33 6V 0.15 0.26 0.4 0.33 6V 0.1 100 1000 1000 nA 2 40 20 A 10 10 10 pF IOL = 4 mA IOL = 5.2 mA VI = VCC or 0 VI = VCC or 0, SN74HC14 MIN 0.2 VI = VIH or VIL II ICC SN54HC14 2V VI = VIH or VIL VOL TA = 25C TYP MAX 4.5 V VT+ - VT- VOH MIN IO = 0 6V Ci 2 V to 6 V 3 V V V switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) TA = 25C MIN TYP MAX SN54HC14 SN74HC14 MIN MIN PARAMETER FROM (INPUT) TO (OUTPUT) VCC 2V 55 125 190 155 tpd d A Y 4.5 V 12 25 38 31 6V 11 21 32 26 2V 38 75 110 95 4.5 V 8 15 22 19 6V 6 13 19 16 tt Y MAX MAX UNIT ns ns operating characteristics, TA = 25C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per inverter POST OFFICE BOX 655303 No load * DALLAS, TEXAS 75265 TYP 20 UNIT pF 3 SCLS085C - DECEMBER 1982 - REVISED NOVEMBER 2002 PARAMETER MEASUREMENT INFORMATION From Output Under Test Test Point Input VCC 50% 50% 0V CL = 50 pF (see Note A) tPLH In-Phase Output LOAD CIRCUIT 50% 10% tPHL 90% 90% tr Input 50% 10% 90% 90% tr VCC 50% 10% 0 V tPHL Out-of-Phase Output 90% tf VOH 50% 10% VOL tf tPLH 50% 10% tf 50% 10% 90% VOH VOL tr VOLTAGE WAVEFORMS PROPAGATION DELAY AND OUTPUT TRANSITION TIMES VOLTAGE WAVEFORM INPUT RISE AND FALL TIMES NOTES: A. CL includes probe and test-fixture capacitance. B. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO = 50 , tr = 6 ns, tf = 6 ns. C. The outputs are measured one at a time with one input transition per measurement. D. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MCFP002A - JANUARY 1995 - REVISED FEBRUARY 2002 W (R-GDFP-F14) CERAMIC DUAL FLATPACK Base and Seating Plane 0.260 (6,60) 0.235 (5,97) 0.045 (1,14) 0.026 (0,66) 0.008 (0,20) 0.004 (0,10) 0.080 (2,03) 0.045 (1,14) 0.280 (7,11) MAX 1 0.019 (0,48) 0.015 (0,38) 14 0.050 (1,27) 0.390 (9,91) 0.335 (8,51) 0.005 (0,13) MIN 4 Places 7 8 0.360 (9,14) 0.250 (6,35) 0.360 (9,14) 0.250 (6,35) 4040180-2 / C 02/02 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only. Falls within MIL STD 1835 GDFP1-F14 and JEDEC MO-092AB POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MLCC006B - OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL MPDI002C - JANUARY 1995 - REVISED DECEMBER 20002 N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE 16 PINS SHOWN PINS ** 14 16 18 20 A MAX 0.775 (19,69) 0.775 (19,69) 0.920 (23,37) 1.060 (26,92) A MIN 0.745 (18,92) 0.745 (18,92) 0.850 (21,59) 0.940 (23,88) MS-100 VARIATION AA BB AC DIM A 16 9 0.260 (6,60) 0.240 (6,10) 1 C AD 8 0.070 (1,78) 0.045 (1,14) 0.045 (1,14) 0.030 (0,76) D D 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gauge Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.430 (10,92) MAX 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M 14/18 PIN ONLY 20 pin vendor option D 4040049/E 12/2002 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001, except 18 and 20 pin minimum body lrngth (Dim A). D. The 20 pin end lead shoulder width is a vendor option, either half or full width. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MSOI002B - JANUARY 1995 - REVISED SEPTEMBER 2001 D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 8 PINS SHOWN 0.020 (0,51) 0.014 (0,35) 0.050 (1,27) 8 0.010 (0,25) 5 0.008 (0,20) NOM 0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81) Gage Plane 1 4 0.010 (0,25) 0- 8 A 0.044 (1,12) 0.016 (0,40) Seating Plane 0.010 (0,25) 0.004 (0,10) 0.069 (1,75) MAX PINS ** 0.004 (0,10) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 4040047/E 09/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated