Continental Device India Limited
An IS/ISO 9002 and IECQ Certified Manufacturer
NPN SILICON HIGH SPEED SWITHCHING TRANSISTORS P2N2369
TO-92
Plastic Package
LOW POWER FOR HIGH SPEED SWITCHING APPLICATIONS
ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise)
DESCRIPTION SYMBOL UNIT
Collector Emitter Voltage VCEO V
Collector Base Voltage VCBO V
Collector Emitter Voltage ( VBE=0) VCES V
Emitter Base Voltage VEBO V
Collector Current Peak ICM mA
Power Dissipation @ Ta=25ºC PDmW
Operating And Storage Junction Tj, Tstg ºC
Temperature Range
THERMAL RESISTANCE
Junction to Ambient in free air Rth(j-a) ºC/W
625
-55 to +150
200
VALUE
15
40
40
4.5
500
C
B
E
IS/ISO 9002
Lic# QSC/L-000019.3
Continental Device India Limited Data Sheet Page 1 of 4
NPN SILICON HIGH SPEED SWITCHING TRANSISTORS P2N2369
TO-92
Plastic Package
ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise)
MIN MAX
Collector Emitter Breakdown Voltage BVCEO IC=10mA, IB=0 15 V
Collector Emitter Breakdown Voltage BVCES IC=10µA, VBE=0 40 V
Collector Base Breakdown Voltage BVCBO IC=10µA, IE=0 40 V
Emitter Base Breakdown Voltage BVEBO IE=10µA, IC=0 4.5 V
Collector Leakage Current ICBO VCB=20V, IE=0 400 nA
Collector Leakage Current ICBO VCB=20V, Ta=125ºC 30 µA
Collector Emitter Saturation Voltage VCE(sat) IC=10mA, IB=1mA 0.25 V
Base Emitter Saturation Voltage VBE(sat) IC=10mA, IB=1mA 0.7 0.85 V
DC Current Gain hFE IC=10mA, VCE=1V 40 120
IC=100mA, VCE=2V* 20
IC=10mA, VCE=1V, 20
Ta= -55ºC
DYNAMIC CHARACTERISTICS
Output Capacitance CcIE=0, VCB=5V 4pF
f=140KHz
Small Signal Current Gain | hfe | VCE =10V,IC=10mA 5MHz
f=100MHZ
SWITCHING CHARCTERISTICS
Turn on Time
t
on
I
C
=10mA, I
B1
=3mA,
12 ns
V
CC
=3V
Turn off Time toff IC=10mA, IB1=3mA, 18 ns
VCC=3V,IB2=1.5mA
Storage Time tsIC=10mA, IB1=10mA= IB2 13 ns
*Pulse Condition: Length < 300
µµ
s, Duty Cycle < 2%.
VALUE UNITTEST CONDITIONSYMBOLDESCRIPTION
C
B
E
Continental Device India Limited Data Sheet Page 2 of 4
P2N2369
TO-92
Plastic Package
TO-92 Transistors on Tape and Ammo Pack
TO-92 Transistors on Tape and Ammo Pack
TO-92 Bulk
TO-92 T&A
1K/polybag
2K/ammo box
200 gm/1K pcs
645 gm/2K pcs
3" x 7.5" x 7.5"
12.5" x 8" x 1.8"
5K
2K
17" x 15" x 13.5"
17" x 15" x 13.5"
80K
32K
23 kgs
12.5 kgs
PACKAGE
Net Weight/Qty
Details
STANDARD PACK INNER CARTON BOX
Qty
OUTER CARTON BOX
Qty Gr WtSize Size
Packing Detail
FF
H
C
3 2 1
PIN CONFIGURATION
1. EMITTER
2. BASE
3. COLLECTOR
All diminsions in mm.
DIM MIN. MAX.
A4.32 5.33
B4.45 5.20
C3.18 4.19
D0.41 0.55
E0.35 0.50
F5 DEG
G1.14 1.40
H1.14 1.53
2.082
K
L
12.70
1.982
—
1
2
3
E
SEC AA
D
B
A
L
Solderability Ensured Dimension With 'L'
Uncontrolled
Beyond 'L'
K
DAA
G
1
2
3
Mechanical Data
T
A
A1
P(p)
C1
C2 W2
Do
F2
F
P2
Po
F1
W1
Wo
W
H1
H2
H3
L
t1
t
Ho
h1 h1
hh
ITEM SYMBOL
SPECIFICATION
PULL - OUT FORCE (P) 6N
MIN. NOM.
BODY WIDTH A1 4.0 4.8
BODY HEIGHT A4.8 5.2
BODY THICKNESS T3.9 4.2
AT TOP OF BODYCOMPONENT ALIGNMENT SIDE VIEW h01.0 AT TOP OF BODYCOMPONENT ALIGNMENT FRONT VIEW h1 01.3
COMPONENT HEIGHT H1 23.25
LENGTH OF SNIPPED LEADS L11.0
t1 0.3-0.6TOTAL TAPE THICKNESS t1.2
CLINCH HEIGHT H3 3.0
LEAD PARALLELISM | C1 - C2 | 0.22
MAX.
PITCH OF COMPONENT P12.7 ± 1.0 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCHFEED HOLE PITCH Po 12.7 ± 0.3
FEED HOLE CENTRE TO
TO BE MEASURED AT BOTTOM OF CLINCH
COMPONENT CENTRE P2 6.35 ± 0.4
DISTANCE BETWEEN OUTER
LEADS F5.08 + 0.6
- 0.2
TAPE WIDTH W18 ± 0.5
HOLD-DOWN TAPE WIDTH Wo 6± 0.2
HOLE POSITION W1 9+ 0.7
- 0.5
HOLD-DOWN TAPE POSITION W2 0.5 ± 0.2
LEAD WIRE CLINCH HEIGHT Ho 16 ± 0.5
FEED HOLE DIAMETER Do 4± 0.2
LEAD - TO - LEAD DISTANCE F1, F2 2.54 + 0.4
STAND OFF H2 0.45 1.45
TOL . REMARKS
NOTES
1. Maximum alignment deviation between leads will not to be greater than 0.2mm.
2. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches.
3. Holddown tape will not exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive.
4. There will be no more than three (3) consecutive missing components in a tape.
5. A tape trailer, having at least three feed holes are provided after the last component in a tape.
6. Splices should not interfere with the sprocket feed holes.
- 0.1
Adhesive Tape on Top Side
Flat side
Flat Side of Transistor and
Adhesive Tape Visible
2000 pcs./Ammo Pack
Label
Carrier
Strip
186
(7.3")
332 (13")
FEED
43
(1.7")
Ammo Pack Style
All dimensions in mm
Continental Device India Limited Data Sheet Page 3 of 4
Notes P2N2369
TO-92
Plastic Package
P2N2369Rev110302D
Disclaimer
The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for
application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to
confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and on the
CDIL Web Site/CD is believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or
incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL
product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life
saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices
or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and
CDIL will not be responsible for any damages resulting from such sale(s).
CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice.
CDIL is a registered Trademark of
Continental Device India Limited
C-120 Naraina Industrial Area, New Delhi 110 028, India.
Telephone + 91-11-579 6150 Fax + 91-11-579 9569, 579 5290
e-mail sales@cdil.com www.cdil.com
Continental Device India Limited Data Sheet Page 4 of 4
