Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide applications. 2. UL Approval Product HIF3B series connectors are UL approved. 3. Mechanism to Prevent Mis-insertion This connector is equipped with the mechanism to prevent Misinsertion as follows. 1 The system provides the convex area to insert the guide-key on the pin header side, and to guide it in combination with the socket convex area (MIL standard). 2 The system embeds and guides the polarizing key in the socket holes. 4. Applicable Cable AWG#28 The applicable cable is UL2651 AWG#28 flat cable (7 cores./ 0.127mm, jacket dia. 0.90.1mm). Product Specifications Current rating : 1A Rating Operating Temperature Range : -55 to +85c (Note 1) Storage Temperature Range : -10 to +60c (Note 2) Storage Humidity Range : 40 to 70% (Note 2) Voltage rating : 200V AC Operating Moisture Range : 40 to 80% Item Specification Condition 1. Insulation Resistance 1000M ohms min. 500V DC 2. Withstanding voltage No flashover or insulation breakdown. 650V AC/1 minute 3. Contact Resistance 15m ohms max. 0.1A 4. Vibration No electrical discontinuity of 1s or more Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance: 1000M ohms min. 6. Temperature Cycle 96 hours at temperature of 40c and humidity of 90% to 95% (-65c: 30 minutes 15 to 35c: 5 minutes max. No damage, cracks, or parts looseness. 125c: 30 minutes 15 to 35c: 5 minutes max.) 5 cycles 7. Durability (Mating/un-mating) Contact resistance: 15m ohms max. 500 cycles Flow: 260c for 10 seconds 8. Resistance to Soldering heat No deformation of components affecting performance. Manual soldering: 300c for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation. Material Part Material Finish Remarks Insulator PBT Black UL94V-0 D Beryllium copper Socket Contact DA Pin header contact Copper alloy Brass Connection area Gold plated Connection area Gold plated Connection area Gold plated Connection area Tin lead plated Selective Gold plated ------- ------- B15 Ordering Information Socket HIF 3B - * D A - 2.54 R q w e r t y u q Series Name : HIF w Series No. : 3B, 3BA, 3BB (50, 60, 64 contacts only) e Number of contacts : 16, 20, 26, 30, 34, 40, 50, 60, 64 r Contact alignment : D : Double t A : VA type y Contact pitch : 2.54mm u Connection type R : ID type Pin Header HIF 3B - * P A - 2.54 DS q w e q Series Name : HIF w Series No. : r t y : (14 contacts not included) 3BC: (10 contacts only) 3BA, 3BB: (50, 60, 64 contacts only) 3BD: (10 contacts only) 3B e Number of contacts : 16, 20, 26, 30, 34, 40, 50, 60, 64 r P t A y Contact pitch : Pin header : Selective gold plated : 2.54mm u Contact style B16 u DS : Right angle type DSA : Straight type Socket (With guide to prevent mis-insertion) Body Protector Clamp Note1, Note2: The number of polarizing keys and polarizing keyways changes according to products. Refer to the list as shown below. Note3: The 50, 60 and 64 contact connector contain two types of polarizing guides. Use the products, referring to Notes 1 and 2. Note4: The 6 contact has no polarizing mark. Unit:mm Part Number CL No. HIF3BA- 6D-2.54R 610-0032-3 Part Number CL No. ------- Number of Contacts A B C D 6 12.19 5.08 6.35 7.72 Polarizing Guide (Note 1) Polarizing Keyway (Note 2) None HIF3BA-10D-2.54R 610-0021-7 HIF3BA-10DA-2.54R 610-0651-5 10 17.27 10.16 11.43 12.8 HIF3BA-14D-2.54R 610-0022-0 HIF3BA-14DA-2.54R 610-0652-8 14 22.35 15.24 16.51 17.88 HIF3BA-16D-2.54R 610-0023-2 HIF3BA-16DA-2.54R 610-0653-0 16 24.89 17.78 19.05 20.42 HIF3BA-20D-2.54R 610-0024-5 HIF3BA-20DA-2.54R 610-0654-3 20 29.97 22.86 24.13 25.5 HIF3BA-26D-2.54R 610-0025-8 HIF3BA-26DA-2.54R 610-0655-6 26 37.59 30.48 31.75 33.12 HIF3BA-30D-2.54R 610-0026-0 HIF3BA-30DA-2.54R 610-0656-9 30 42.67 35.56 36.83 38.2 HIF3BA-34D-2.54R 610-0027-3 HIF3BA-34DA-2.54R 610-0657-1 34 47.75 40.64 41.91 43.28 HIF3BA-40D-2.54R 610-0028-6 HIF3BA-40DA-2.54R 610-0658-4 40 55.37 48.26 49.53 50.9 HIF3BA-50D-2.54R 610-0029-9 HIF3BA-50DA-2.54R 610-0659-7 50 One on right and 68.07 60.96 62.23 63.6 One on right and left sides, resp. left sides, resp. HIF3BB-50D-2.54R 610-0041-4 HIF3BB-50DA-2.54R 610-0671-2 50 68.07 60.96 62.23 63.6 HIF3BA-60D-2.54R 610-0030-8 HIF3BA-60DA-2.54R 610-0660-6 60 80.77 73.66 74.93 76.3 One on right and left sides, resp. HIF3BB-60D-2.54R 610-0042-7 HIF3BB-60DA-2.54R 610-0672-5 60 80.77 73.66 74.93 76.3 HIF3BA-64D-2.54R 610-0031-0 HIF3BA-64DA-2.54R 610-0661-9 64 85.85 78.74 80.01 81.38 One on right and left sides, resp. HIF3BB-64D-2.54R 610-0043-0 HIF3BB-64DA-2.54R 610-0673-8 64 85.85 78.74 80.01 81.38 One on left side One at center One at center One at center One at center The products marked with comply with MIL standard. B17 Socket with Withdrawal Tab Unit : mm B18 Part Number CL No. Number of Contacts A B HIF3BA-10D-2.54R-CL 610-0190-4 10 17.27 5.3 HIF3BA-16D-2.54R-CL 610-0192-0 16 24.89 12.9 HIF3BA-20D-2.54R-CL 610-0193-2 20 29.97 18.0 HIF3BA-26D-2.54R-CL 610-0194-5 26 37.59 25.5 HIF3BA-30D-2.54R-CL 610-0195-8 30 42.67 30.5 HIF3BA-34D-2.54R-CL 610-0196-0 34 47.75 35.8 HIF3BA-40D-2.54R-CL 610-0197-3 40 55.37 43.4 HIF3BA-50D-2.54R-CL 610-0198-6 HIF3BB-50D-2.54R-CL 610-0201-9 50 68.07 56.0 HIF3BA-60D-2.54R-CL 610-0199-9 HIF3BB-60D-2.54R-CL 610-0202-1 60 80.77 68.5 HIF3BA-64D-2.54R-CL 610-0200-6 HIF3BB-64D-2.54R-CL 610-0203-4 64 85.85 73.8 Socket Body Protector Clamp Note1: The number of polarizing keys and polarizing keyways changes according to products. For details, refer to the list as shown below. Note2: The 6 contact has no polarizing mark. Unit:mm Part Number CL No. Number of Contacts A B C D HIF3B- 6D-2.54R 610-0012-6 6 12.19 5.08 6.35 7.72 HIF3B-10D-2.54R 610-0001-0 10 17.27 10.16 11.43 12.80 HIF3B-14D-2.54R 610-0002-2 14 22.35 15.24 16.51 17.88 HIF3B-16D-2.54R 610-0003-5 16 24.89 17.78 19.05 20.42 HIF3B-20D-2.54R 610-0004-8 20 29.97 22.86 24.13 25.50 HIF3B-26D-2.54R 610-0005-0 26 37.59 30.48 31.75 33.12 HIF3B-30D-2.54R 610-0006-3 30 42.67 35.56 36.83 38.2 HIF3B-34D-2.54R 610-0007-6 34 47.75 40.64 41.91 43.28 HIF3B-40D-2.54R 610-0008-9 40 55.37 48.26 49.53 50.90 HIF3B-50D-2.54R 610-0009-1 50 68.07 60.96 62.23 63.6 HIF3B-60D-2.54R 610-0010-0 60 80.77 73.66 74.93 76.3 64 85.85 78.74 80.01 81.38 HIF3B-64D-2.54R 610-0011-3 Polarizing Guide (Note 1) None One on left side One on right and left sides, resp. The products marked with comply with MIL standard. B19 Four Wall Angle Through hole BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors contain two types of polarizing slots. Use products, referring to (Note 1) (Note 2). n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C HIF3BA-10PA-2.54DS 610-0091-2 10 32.0 17.5 10.16 HIF3BD-10PA-2.54DS 610-0171-0 10 32.0 17.5 10.16 HIF3BA-14PA-2.54DS 610-0092-5 14 37.1 22.6 15.24 HIF3BA-16PA-2.54DS 610-0093-8 16 39.6 25.1 17.78 HIF3BA-20PA-2.54DS 610-0094-0 20 44.7 30.2 22.86 HIF3BA-26PA-2.54DS 610-0095-3 26 52.3 37.8 30.48 HIF3BA-30PA-2.54DS 610-0096-6 30 57.4 42.9 35.56 HIF3BA-34PA-2.54DS 610-0097-9 34 62.5 48.0 40.64 HIF3BA-40PA-2.54DS 610-0098-1 40 70.1 55.6 48.26 HIF3BA-50PA-2.54DS 610-0099-4 50 82.8 68.3 60.96 HIF3BB-50PA-2.54DS 610-0131-5 50 82.8 68.3 60.96 HIF3BA-60PA-2.54DS 610-0100-1 60 95.5 81.0 73.66 HIF3BB-60PA-2.54DS 610-0132-8 60 95.5 81.0 73.66 HIF3BA-64PA-2.54DS 610-0101-4 64 100.6 86.1 78.74 HIF3BB-64PA-2.54DS 610-0133-0 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 33.24 MAX56.2 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 None 26.9 33.0 One on right side 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with comply with MIL standard. B20 Four-Wall Straight Through hole BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors contain two types of polarizing slots. Use products, confirming (Note 1) (Note 2). Note 5: The 6 contact has no polarity mark. n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C HIF3-6PA-2.54DSA 562-0503-9 6 26.92 12.42 05.08 HIF3BA-10PA-2.54DSA HIF3BD-10PA-2.54DSA 610-0111-8 10 32.0 17.5 10.16 610-0181-3 10 32.0 17.5 10.16 HIF3BA-14PA-2.54DSA 610-0112-0 14 37.1 22.6 15.24 HIF3BA-16PA-2.54DSA 610-0113-3 16 39.6 25.1 17.78 HIF3BA-20PA-2.54DSA 610-0114-6 20 44.7 30.2 22.86 HIF3BA-26PA-2.54DSA 610-0115-9 26 52.3 37.8 30.48 HIF3BA-30PA-2.54DSA 610-0116-1 30 57.4 42.9 35.56 HIF3BA-34PA-2.54DSA 610-0117-4 34 62.5 48.0 40.64 HIF3BA-40PA-2.54DSA 610-0118-7 40 70.1 55.6 48.26 HIF3BA-50PA-2.54DSA 610-0119-0 50 82.8 68.3 60.96 HIF3BB-50PA-2.54DSA 610-0141-9 50 82.8 68.3 60.96 HIF3BA-60PA-2.54DSA 610-0120-9 60 95.5 81.0 73.66 HIF3BB-60PA-2.54DSA 610-0142-1 60 95.5 81.0 73.66 HIF3BA-64PA-2.54DSA 610-0121-1 64 100.6 86.1 78.74 64 100.6 86.1 78.74 HIF3BB-64PA-2.54DSA 610-0143-4 D 23.06 MAX46.02 28.14 MAX51.1 28.14 MAX51.1 33.24 MAX56.2 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) 16.7 22.82 One at center None 21.8 27.9 None One on right side E F 21.8 27.9 None 26.9 33.0 One on right side 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with comply with MIL standard. B21 Three Wall Angle Type BPCB mounting pattern Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves according to the number of contacts. Note 4: The 10 contact connector consists of two types. Use products, confirming (Note 1) (Note 2). Note 5: The 6 contact has no polarity mark. Note 6: The nut built-in specification product is also provided. The product can be fixed by M2 screws from the rear side. Use the screw of (board thickness) +4 mm under the neck. n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C HIF3BD-10PA-2.54DS 610-0051-8 10 32.0 17.5 10.16 HIF3BC-10PA-2.54DS 610-0151-2 10 32.0 17.5 10.16 HIF3BD-16PA-2.54DS 610-0052-0 16 39.6 25.1 17.78 HIF3BD-20PA-2.54DS 610-0053-3 20 44.7 30.2 22.86 HIF3BD-26PA-2.54DS 610-0054-6 26 52.3 37.8 30.48 HIF3BD-30PA-2.54DS 610-0055-9 30 57.4 42.9 35.56 HIF3BD-34PA-2.54DS 610-0056-1 34 62.5 48.0 40.64 HIF3BD-40PA-2.54DS 610-0057-4 40 70.1 55.6 48.26 HIF3BD-50PA-2.54DS 610-0058-7 50 82.8 68.3 60.96 HIF3BD-60PA-2.54DS 610-0059-0 60 95.5 81.0 73.66 HIF3BD-64PA-2.54DS 610-0060-9 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 91.64 MAX114.6 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 One on right and left sides, resp. 59.9 66.0 72.6 78.7 85.3 91.4 One on right and left sides, resp. 90.4 96.5 The products marked with comply with MIL standard. B22 Three Wall Straight Through hole BPCB mounting pattern Note1,Note2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note3: The spacer moves to the right according to the number of contacts. Note4: The 10 contact connector consists of two types. Use products, referring to (Note 1) and (Note 2). Note5: The 6 contact has no polarity mark. n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C HIF3BD-10PA-2.54DSA 610-0071-5 10 32.0 17.5 10.16 HIF3BC-10PA-2.54DSA 610-0161-6 10 32.0 17.5 10.16 HIF3BD-16PA-2.54DSA 610-0072-8 16 39.6 25.1 17.78 HIF3BD-20PA-2.54DSA 610-0073-0 20 44.7 30.2 22.86 HIF3BD-26PA-2.54DSA 610-0074-3 26 52.3 37.8 30.48 HIF3BD-30PA-2.54DSA 610-0075-6 30 57.4 42.9 35.56 HIF3BD-34PA-2.54DSA 610-0076-9 34 62.5 48.0 40.64 HIF3BD-40PA-2.54DSA 610-0077-1 40 70.1 55.6 48.26 HIF3BD-50PA-2.54DSA 610-0078-4 50 82.8 68.3 60.96 HIF3BD-60PA-2.54DSA 610-0079-7 60 95.5 81.0 73.66 HIF3BD-64PA-2.54DSA 610-0080-6 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 91.64 MAX114.6 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 One on right and left sides, resp. 59.9 66.0 72.6 78.7 85.3 91.4 One on right and left sides, resp. 90.4 96.5 The products marked with comply with MIL standard. B23 Four Wall Wrapping Type BPCB mounting pattern Note 1, Note 2. The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3. The spacer moves to the right according to the number of contacts. Note 4. The 10, 50, 60 and 64 contact connectors consists of two types. Use products, confirming (Note 1) (Note 2). Note 5. The mark * indicates the number of contacts. Note 6. The nut built-in specification product is also provided. The product can be fixed by M2 screws from the rear side. Use the screw of (board thickness) +4 mm under the neck. n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C HIF3BA-10P-2.54W 610-0503-8 10 32.0 17.5 10.16 HIF3BD-10P-2.54W 610-0492-3 10 32.0 17.5 10.16 HIF3BA-14P-2.54W 610-0493-6 14 37.1 22.6 15.24 HIF3BA-16P-2.54W 610-0494-9 16 39.6 25.1 17.78 HIF3BA-20P-2.54W 610-0495-1 20 44.7 30.2 22.86 HIF3BA-26P-2.54W 610-0496-4 26 52.3 37.8 30.48 HIF3BA-30P-2.54W 610-0497-7 30 57.4 42.9 35.56 HIF3BA-34P-2.54W 610-0498-0 34 62.5 48.0 40.64 HIF3BA-40P-2.54W 610-0499-2 40 70.1 55.6 48.26 HIF3BA-50P-2.54W 610-0504-0 50 82.8 68.3 60.96 HIF3BB-50P-2.54W 610-0500-0 50 82.8 68.3 60.96 HIF3BA-60P-2.54W 610-0505-3 60 95.5 81.0 73.66 HIF3BB-60P-2.54W 610-0501-2 60 95.5 81.0 73.66 HIF3BA-64P-2.54W 610-0506-6 64 100.6 86.1 78.74 HIF3BB-64P-2.54W 610-0502-5 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 33.24 MAX56.2 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 None 26.9 33.0 One on right side 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with comply with MIL standard. B24 Four Wall Straight Through hole [Flux Blister Prevention Type] BPCB mounting pattern Note1: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. n=number of contacts Unit:mm Part Number CL No. Number of Contacts A B C HIF3CA-10PA-2.54DSA 610-0701-1 10 32.0 17.5 10.16 HIF3CD-10PA-2.54DSA 610-0722-1 10 32.0 17.5 10.16 HIF3CA-16PA-2.54DSA 610-0703-7 16 39.6 25.1 17.78 HIF3CA-20PA-2.54DSA 610-0704-0 20 44.7 30.2 22.86 HIF3CA-26PA-2.54DSA 610-0705-2 26 52.3 37.8 30.48 HIF3CA-30PA-2.54DSA 610-0706-5 30 57.4 42.9 35.56 HIF3CA-34PA-2.54DSA 610-0707-8 34 62.5 48.0 40.64 HIF3CA-40PA-2.54DSA 610-0708-0 40 70.1 55.6 48.26 HIF3CA-50PA-2.54DSA 610-0709-3 50 82.8 68.3 60.96 HIF3CB-50PA-2.54DSA 610-0721-9 50 82.8 68.3 60.96 HIF3CB-60PA-2.54DSA 610-0723-4 60 95.5 81.0 73.66 HIF3CB-64PA-2.54DSA 610-0724-7 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot Polarizing Key Install None One on right side 21.8 27.9 None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 One on right and left sides, resp. 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 85.3 91.4 One at center 90.4 96.5 The products marked with comply with MIL standard. B25 Two Stage Staking Right Angle Through hole Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer to the list as shown below. Note 3: The spacer moves to the right according to the number of contacts. Note 4: The 10, 50, 60 and 64 contact connectors consists of two types. Use products, confirming (Note 1) (Note 2). Note 5: The mark * ndicates the number of contacts. Note 6: The locator is located optionally. Unit:mm Part Number CL No. Number of Contacts 610-1502-0 10 32.0 17.5 10.16 HIF3BD-10PA-2.54WB 610-1503-3 HIF3BA-10PA-2.54WB A B C 10 32.0 17.5 10.16 HIF3BA-16PA-2.54WB 610-1505-9 16 39.6 25.1 17.78 HIF3BA-20PA-2.54WB 610-1506-1 20 44.7 30.2 22.86 HIF3BA-26PA-2.54WB 610-1507-4 26 52.3 37.8 30.48 HIF3BA-30PA-2.54WB 610-1508-7 30 57.4 42.9 35.56 HIF3BA-34PA-2.54WB 610-1509-0 34 62.5 48.0 40.64 HIF3BA-40PA-2.54WB 610-1510-9 40 70.1 55.6 48.26 HIF3BA-50PA-2.54WB 610-1511-1 50 82.8 68.3 60.96 HIF3BB-50PA-2.54WB 610-1512-4 50 82.8 68.3 60.96 HIF3BA-60PA-2.54WB 610-1513-7 60 95.5 81.0 73.66 HIF3BB-60PA-2.54WB 610-1514-0 60 95.5 81.0 73.66 HIF3BA-64PA-2.54WB 610-1515-2 64 100.6 86.1 78.74 HIF3BB-64PA-2.54WB 610-1516-5 64 100.6 86.1 78.74 D 28.14 MAX51.1 28.14 MAX51.1 35.74 MAX58.7 40.84 MAX63.8 48.44 MAX71.4 53.54 MAX76.5 58.64 MAX81.6 66.24 MAX89.2 78.94 MAX101.9 78.94 MAX101.9 91.64 MAX114.6 91.64 MAX114.6 96.74 MAX119.7 96.74 MAX119.7 E F 21.8 27.9 Polarizing Slot (Note 1) Polarizing Key Install (Note 2) None One on right side 21.8 27.9 None 29.5 35.5 34.5 40.6 42.2 48.3 One at center 47.2 53.3 52.3 58.4 59.9 66.0 72.6 78.7 One on right and left sides, resp. 72.6 78.7 One on right and left sides, resp. One at center 85.3 91.4 One on right and left sides, resp. 85.3 91.4 One at center 90.4 96.5 One on right and left sides, resp. 90.4 96.5 One at center The products marked with comply with MIL standard. B26 BCombination Pattern Note : Fix the HIF3-mounting hole spacer by screws between upper stage and lower stage connectors. BPCB mounting pattern Mounting Hole Spacer Part Number CL No. HIF-3 mounting hole spacer 562-0714-4 Finish PBT Black Note : 2 pieces are contained in a bag. B27 BPolarizing Key HIF3B-GK CL562-0601-8 HIF3-GPIN(A) HIF3BA-GPIN Note1: One unit of this product is a set of five pieces in conjunction with a runner. The unit for sale is defined one pack containing 20 pieces. Note2: This product is applicable to HIF3A*D2.54R, HIF3C*D2.54C and HIF3BA-*D2.54C products. Part Number CL No. HIF3-GPIN(A) 562-0126-6 B28 Material Remarks Poly acetal (white) A set of 5 pieces Note1: One unit of this product is a set of five pieces in conjunction with a runner. The unit for sale is defined one pack containing 20 pieces. Note2: This product is applicable to the HIF3BA-*D2.54R product. Part Number CL No. HIF3BA-GPIN 612-0500-2 Material Remarks Poly acetal (white) A set of 5 pieces BHIF3-Multi Clamp BHIF3-*CL Pull Tab This clamp is used for intermediate connection in the This pull tab is used for the HIF3 series equipped with cable clamp bus-line system, etc. Remove compulsory force from the function. Remove all compulsory force, which is loaded on the insulation displacement area of the connector in insulation displacement area of the connector for extraction. intermediate connection. Note: This HIF3-* Pull Tab can not be used for HIF3BA-*PD. Note: The pin header corresponds to the HIF3BAE Note: The pin header corresponds to the HIF3BAE series (lock E). series (lock E). BLock Lock G Lock F Part Number : HIF3BAG-**PA-2.54DSA Part Number : HIF3BAG-**PA-2.54DSA Low profile type, and used for lock ejection. Connector height is reduced. Since no connector clamp is needed on the cable side, this is used without turning back on the cable side. Take care about this point. 27.3 F Type Lock Pin Header 21.5 Low Profile Lock Pin Header Locking range more reduced than conventional lock type. Even if connectors are aligned laterally, the mounting space is reduced. Note : The clamp must be replaced for HIF3A socket type 50 contacts only. Take care about this point. B29 Socket for Crimping Unit: mm B30 Part Number CL No. Number of Contacts A B HIF3BA-10D-2.54C 610-1041-0 10 17.25 10.16 HIF3BA-14D-2.54C 610-1051-3 14 22.35 15.24 HIF3BA-16D-2.54C 610-1042-2 16 24.8 17.78 HIF3BA-20D-2.54C 610-1043-5 20 29.95 22.86 HIF3BA-26D-2.54C 610-1044-8 26 37.55 30.48 HIF3BA-30D-2.54C 610-1045-0 30 42.63 35.56 HIF3BA-34D-2.54C 610-1046-3 34 47.75 40.64 HIF3BA-40D-2.54C 610-1047-6 40 55.35 48.26 HIF3BA-50D-2.54C 610-1048-9 HIF3BB-50D-2.54C 610-1061-7 50 68.04 60.96 HIF3BA-60D-2.54C 610-1049-1 HIF3BB-60D-2.54C 610-1062-0 60 80.77 73.66 HIF3BA-64D-2.54C 610-1064-5 HIF3BB-64D-2.54C 610-1063-2 64 85.85 78.74 Polarizing Guide One at center One right and left side, resp. One at center One right and left side, resp. One at center One right and left side, resp. One at center Cover Case for Crimping socket Unit: mm Part Number CL No. Number of Contacts A B C D E HIF3-20CV 562-0201-0 20 24.5 18.0 12.0 30.5 29.95 HIF3-26CV 562-0202-2 26 30.2 20.0 14.0 32.0 37.55 HIF3-30CV 562-0203-5 30 32.2 22.0 16.0 33.0 42.63 HIF3-34CV 562-0204-8 34 34.2 24.0 18.0 33.5 47.75 HIF3-40CV 562-0205-0 40 36.2 26.0 20.0 35.5 55.35 HIF3-50CV 562-0206-3 50 39.2 29.0 23.0 38.0 68.04 HIF3-60CV 562-0207-6 60 42.2 32.0 26.0 40.5 80.77 Note: The type F lock pin header cannot be used for a mating member. B31 Contact for Crimping Socket HIF3-2226SC HIF3-2226SCA Applicable cable Manual crimping tool 562-0079-8 gold plated contact in bag 562-0244-2 Selective gold plated contact in bag AWG#22 to #26 UL 1007 Stranded wire HIF3-T2226HC HIF3-2226SCF 562-0080-7 gold plated contact in reel * HIF3-2226SCFA 562-0245-5 Selective gold plated contact in reel Applicable cable AWG#22 to #26 UL 1007 Stranded wire Note:* products have both side careers. 562-0124-0 gold plated contact in bag 562-0246-8 Selective gold plated contact in bag AWG#24 to #28 UL 1007 Stranded wire HIF3-TA2428HC HIF3-2022SC 562-0492-4 gold plated contact in bag Applicable cable AWG#20 to #22 UL 1007 Stranded wire Manual crimping tool HIF3-TA2022HC HIF3-2428SCF 562-0125-3 gold plated contact in reel * HIF3-2428SCFA 562-0247-0 Selective gold plated contact in reel Applicable cable AWG#24 to #28 UL 1007 Stranded wire HIF3-2022SCF 562-0493-7 gold plated contact in reel Applicable cable AWG#20 to #22 UL 1007 Stranded wire HIF3-2428SC HIF3-2428SCA Applicable cable Manual crimping tool Type VA (Selective gold plated in reel) Applicable Cable Part Number CL No. HIF3-2226SCFC 613-0002-1 AWG#22 to #26 UL 1007 Stranded wire HIF3-2630SCFC 613-0001-9 AWG#26 to #30 UL 1007 Stranded wire HIF3A-3236SCFC 613-0005-0 AWG#32 to #36 UL 1007 Stranded wire Type VA (Selective gold plated contact in bag) Applicable Cable Manual Crimp Tool A B C D E F Part Number CL No. HIF3-2226SCC 613-0004-7 AWG#22 to #26 UL 1007 Stranded wire HIF3-TB2226HC 11.5 0.8 1.8 1.8 2.3 2.6 HIF3-2630SCC 613-0003-4 AWG#26 to #30 UL 1007 Stranded wire HIF3-TB2630HC 11.5 0.8 1.4 1.35 2.0 2.1 B32 A 11.5 11.5 12.4 B 0.8 0.8 1.7 C 1.8 1.4 1.1 D 1.8 1.35 1.1 E 2.3 2.0 1.4 F 2.6 2.1 1.5 BTools Crimping Tool Manual Crimping Tool Part Number CL No. HIF3-T2226HC 550-0063-8 HIF3-T2226HC Automatic Crimping Tool (Type: CM-105) Contact Extraction Tools Part Number CL No. HIF1-PO 550-0049-7 Part Number CL No. CM-105 901-0005-4 How to use the extraction tool (1) How to extract contacts (2) How to adjust the lance (raise) As shown in Figure 1, where the extraction tool is inserted in the lance fixed slot on the insulated case, slightly pull the cable, and the contact can be removed. In order to re-insert the contact removed from the insulated case, raise the contact lance area using the tool A, and re-insert the contact, as shown in Figure 2. Figure 1 B33 Type Item Manual Manual crimping tool Automatic Part Number CL No. 550-0063-8 HIF3-TA2428HC 550-0100-2 HIF3-TA2022HC 550-0124-0 HIF3-2022SC AWG#20 to #22 HIF3-TB2226HC 550-0154-1 HIF3-2226SCC AWG#22 to #26 HIF3-TB2630HC 550-0155-4 HIF3-2630SCC AWG#26 to #30 901-0005-4 ------- HIF3-2226SCF HIF3-2428SCF HIF3-2226SCFA HIF3-2428SCFA ------- AWG#22 to #26 AWG#24 to #28 AWG#22 to #26 AWG#24 to #28 AP105-HIF3-22-28SCF 901-4031-6 (Note1) AP105-HIF3-22-28SCFA 901-4030-3 (Note1) Extraction tool HIF3-2226SC HIF3-2226SCA HIF3-2428SC HIF3-2428SCA AWG#22 to #26 AWG#24 to #28 AP105-HIF3-2022S 901-4027-9 HIF3-2022SCF AWG#20 to #22 AP105-HIF3-2226SCFC 901-4005-6 HIF3-2226SCFC AWG#22 to #26 AP105-HIF3-2630SCFC 901-4006-9 HIF3-2630SCFC AWG#26 to #30 AP105-HIF3-3236SCFC 901-4007-1 HIF3-3236SCFC AWG#32 to #36 HIF1-PO 550-0049-7 ------- ------- Note1: AP106-HIF3-22-28SCF and AP105-HIF3-22-28CFA can be modified by changing a few parts. B34 Applicable Cable HIF3-T2226HC Automatic crimping tool unit CM-105 Applicator Applicable Contact BSocket Side (Crimping) Assembling Procedures (1) As shown in Figure 1, peel the applicable cable (AWG#20 to #26) jacket, and connect it using crimping jig HIF3-TA2022HC, HIF3-TA2226HC, or HIF3-TA2426HC. In this case, insert the cable so as to hit the contact cable stripper position as shown Figure 2. (2) After connection as shown Figure 2, check the contact direction, and insert the contact as shown Figures 3 and 4. Slightly pull the cable, and check whether the contact lance position is firmly fixed to the insulation case, as shown in the area (A). Note : For handling procedures for special crimping tools, refer to the "Handling Instruction Manual". Figure 1 Figure 2 Figure 3 Figure 4 B35 HIF3B Connection Circuit Diagram Type AB Type AB Type AD Type AD Type CD Type CD B36 Type AC Type AC Type CC Type CC Type AA Type AA B37 HIF2E R(S) A to HIF3B Connection Circuit Diagram Type AA Type AC B38 Type BA Type BC B39 HIF2E R(S)B to HIF3 Connection Circuit Diagram Type AA Type AC B40 Type BA Type BC B41