APL5501/2/3 Low IQ, Low Dropout 500mA Fixed Voltage Regulator Features APL5501 BP 5 1 2 3 V IN GND Notebook Computer PDA or Portable Equipments Noise-Sensitive Instrumentation Systems General Description IN 1 8 OU T GND 2 7 GN D GND 3 6 GN D SHDN 4 5 BY P 2 3 V O UT G N D V OUT V IN SOT-89-5 (Top View) V IN 1 GND 2 SHDN 3 SO-8 (Top View) The APL5501/2/3 is micropower, low noise, low dropout linear regulator. Operate from 2.7V to 6V input voltage and deliver up to 500mA. Typical output noise is just 50VRMS with the addition of an external 0.1F bypass capacitor in BP pin and typical dropout voltage is only 170mV at 500mA loading . Designed for use in battery-powered system, the low 50uA quiescent current makes it an ideal choice. 4 1 SOT-89 (Top View) Applications * * * GND SHDN T A B is G N D 5 VOUT 4 BP SOT-23-5 (Top View) G ND 1 V IN 2 3 5 Built in Current Limit Protection Controlled Short Circuit Current : 150mA Fast Transient Response Short Setting Time SOT-23-5, SOT-89, SOT-89-5, SOT-223, SO-8 ,TO-252 and TO-252-5 Packages VOUT 4 * * * * * BP 3 Built in Thermal Protection Pin Configuration GND 2 * Design with an internal P-channel MOSFET pass transistor, the APL5501/2/3 maintains a low supply current, independent of the load current and dropout voltage. Other features include reverse current protection, thermal-shutdown protection, current limit protection to ensure specified output current and controlled short-circuit current. The APL5501/2/3 regulator comes in a miniature SOT-23-5, SOT-89, SOT89-5, SOT-223, SO-8, TO-252 and TO-252-5 packages. SHDN 1 * * Low Noise : 50VRMS (100Hz to 100kHz) Low Quiescent Current : 50A (No load) Low Dropout Voltage : 170mV (@500mA) Very low Shutdown Current : < 0.5uA Fixed Output Voltage : 1.3V ~ 3.4V Stable with 4.7uF Output Capacitor Stable with Aluminum , Tantalum or Ceramic Capacitors . Reverse Current Protection No Protection Diodes Needed TAB is GND * * * * * * * VIN V O UT TO-252 (Top View) TO-252-5 (Top View) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 1 www.anpec.com.tw APL5501/2/3 Pin Configuration (Cont.) APL5501 APL5502 APL5502 APL5503 T A B is V IN T A B is G N D T A B is G N D TAB is V IN 1 2 3 V IN GND V O UT SOT-223 (Top View) 1 2 GND V IN 3 V OUT SOT-89 (Top View) 1 2 3 GND V IN V O UT SOT-223 (Top View) 1 2 V O UT G N D 3 V IN SOT-223 (Top View) Ordering and Marking Information P ackage Code B : S O T -2 3 -5 D : S O T -8 9 U : T O -2 5 2 U 5 : T O - 2 5 2 -5 K : S O -8 Tem p. R ange C : 0 to 7 0 C H a n d lin g C o d e TR : Tape & R eel V o lt a g e C o d e : 1 3 : 1 .3 V ~ 3 4 : 3 .4 V A P L 5 5 0 1 /2 /3 H a n d lin g C o d e Tem p. R ange D 5 : S O T -8 9 -5 V : S O T -2 2 3 P ackage Code V o lt a g e C o d e A P L 5 5 0 1 /2 / 3 - 1 3 D / V /K : A P L 5 5 0 1 /2 / 3 X XX XX 13 XXXXX - D a te C o d e , 1 3 - 1 .3 V A P L 5 5 0 1 /2 / 3 - 1 3 U : 13 A P L 5 5 0 1 /2 / 3 XXXXX XXXXX - D a te C o d e , 1 3 - 1 .3 V Marking Information SOT-23-5 package Product Name APL5501-13B APL5501-14B APL5501-15B APL5501-16B APL5501-17B APL5501-18B APL5501-19B APL5501-20B APL5501-21B APL5501-22B APL5501-23B APL5501-24B APL5501-25B APL5501-26B APL5501-27B Marking 517X 518X 519X 51AX 51BX 51CX 51DX 51EX 51FX 51GX 51HX 51IX 51JX 51KX 51LX Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 Product Name APL5502-13B APL5502-14B APL5502-15B APL5502-16B APL5502-17B APL5502-18B APL5502-19B APL5502-20B APL5502-21B APL5502-22B APL5502-23B APL5502-24B APL5502-25B APL5502-26B APL5502-27B Marking 527X 528X 529X 52AX 52BX 52CX 52DX 52EX 52FX 52GX 52HX 52IX 52JX 52KX 52LX 2 Product Name APL5503-13B APL5503-14B APL5503-15B APL5503-16B APL5503-17B APL5503-18B APL5503-19B APL5503-20B APL5503-21B APL5503-22B APL5503-23B APL5503-24B APL5503-25B APL5503-26B APL5503-27B Marking 537X 538X 539X 53AX 53BX 53CX 53DX 53EX 53FX 53GX 53HX 53IX 53JX 53KX 53LX www.anpec.com.tw APL5501/2/3 Marking Information (Cont.) SOT-23-5 package Product Name APL5501-28B APL5501-29B APL5501-30B APL5501-31B APL5501-32B APL5501-33B APL5501-34B Marking 51MX 51NX 51OX 51PX 51QX 51RX 51SX Product Name APL5502-28B APL5502-29B APL5502-30B APL5502-31B APL5502-32B APL5502-33B APL5502-34B Marking 52MX 52NX 52OX 52PX 52QX 52RX 52SX Product Name APL5503-28B APL5503-29B APL5503-30B APL5503-31B APL5503-32B APL5503-33B APL5503-34B Marking 53MX 53NX 53OX 53PX 53QX 53RX 53SX The last character "X" in the marking is for data code. Pin Description No. 1 2 PIN Name VIN SHDN (Note1) 3 GND 4 5 BP(Note1) VOUT I/O Description I I Supply voltage input. Shutdown control pin, low = off , high = normal . Ground pins of the circuitry, and all ground pins must be soldered to PCB with proper power dissipation. Bypass signal pin in fixed output type device Output pin of the regulator. O O Note1 : These pins do not exist in 3-pin package. Absolute Maximum Ratings Symbol VIN, VOUT SHDN R TH,JA PD TJ T STG TL Parameter Input Voltage or Out Voltage Shutdown Control Pin Thermal Resistance - Junction to Ambient Power Dissipation Operating Junction Temperature Control Section Power Transistor Storage Temperature Range Lead Temperature (Soldering, 10 second) Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 3 Rating 5 Unit V 5 V SOT-89 : 180 SOT-223 : 135 SO-8 : 210 SOT-23-5 : 357 Internally Limited C/W W C 0 to 125 0 to 150 -65 to +150 260 C C www.anpec.com.tw APL5501/2/3 Electrical Characteristics Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1F, COUT=4.7F, SHDN=VIN, TJ=0 to 125C. Typical values refer to TJ=25C. APL5501/2/3 Symbol Parameter Test Conditions Unit Min. Typ. Max. VIN Input Voltage 2.7 6 V VOUT Output Voltage VOUT+1.0V< VCC<6.0V, 0mA< IOUT < IMAX VOUT -2% VOUT VOUT +2% V VIN=4.3V ILIMIT Circuit Current Limit 0.7 A ISHORT Short Current VOUT=0V 200 mA Load Current IOUT 500 mA REGLINE Line Regulation VOUT+0.5V< VCC<6.0V, 0mA< IOUT < IMAX 4 10 mV Load Regulation V =V +1.0V, 0mA< I < I 1 mV REGLOAD 6 IN OUT OUT MAX (Note2) Dropout Voltage IOUT =500mA VDROP (V OUT(Nominal)=3.0V 170 300 mV Version) F1kHz, 1Vpp at VIN = VOUT+1.0V PSRR Ripple Rejection 55 65 dB IQ Quiescent Current Shutdown Supply Current(Note3) Noise(Note3) OTS Shutdown Recovery Delay (Note3) Over Temperature Shutdown Over Temperature Shutdown Hysteresis TC No load 50 100 IOUT=500mA 370 450 Shutdown = low IOUT=0, VCC =6.0V 0.01 1 100Hz<f<100kHz, typical load, CBP=0.01F, COUT = 1F 100Hz<f<100kHz, typical load, CBP=0.1F, COUT = 1F CBP=0.01F,COUT=1F, no load CBP=0.1F,COUT=1F, no load Hysteries Output Voltage Temperature Coefficient A A 50 Vrms 40 7 70 ms 150 C 10 C 50 ppm/C Output Capacitor 4.2 4.7 5.2 F ESR 0.02 0.1 1 Ohm Shutdown Input VOUT+1.0V< VIN <6.0V 0.4 0.7 1.6 V Threshold(Note3) Shutdown input Bias ISHDN VSHDN =VIN 0.01 100 nA current(Note3) Input Reverse Leakage 0.1 0.5 VOUT-VIN=0.1V A current Reverse Protection 11 50 mV Threshold Note 2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 0.5V Note 3 : For 5-pin devices only. COUT Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 4 www.anpec.com.tw APL5501/2/3 Application Circuit IN P U T 2 .7 V to 6 V V IN V OUT VO UT A P L5501/2/3 C IN 1uF BP SHDN on C OUT 4.7uF GND off C BP Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 5 0.1uF www.anpec.com.tw APL5501/2/3 Typical Characteristics Ground Pin Current vs. Load Current (uA) Current Limit vs. Input Voltage APL5501/2/3-33 3 Current Limit (mA) 2.5 2 1.5 1 0.5 0 3.5 4 4.5 5 5.5 6 Ground Pin Current vs. Output Current APL5501/2/3-33 400 350 300 250 200 150 100 50 0 0 150 Ground Pin Current vs. Input Voltage 600 750 900 Input Voltage vs. Output Voltage APL5501/2/3-33 APL5501/2/3-33 3.5 3 300 Output Voltage (V) Ground Pin Current vs. Load Current (uA) 450 Output Current (mA) Input Voltage (V) 350 300 250 200 150 100 2.5 2 1.5 1 0.5 50 0 0 0 1 2 3 4 5 0 6 2 3 4 5 6 Input Voltage (V) Input Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 1 6 www.anpec.com.tw APL5501/2/3 Typical Characteristics Output Current vs. Output Voltage Dropout Voltage vs. Output Current APL5501/2/3-33 APL5501/2/3-33 0 -2 200 Output Current (uA) Dropout Voltage (mV) 250 150 100 50 -4 VIN=0V -6 -8 -10 0 -12 0 150 300 450 600 750 900 0 0.5 1 Output Current (mA) 2 2.5 PSRR vs. Frequency APL5501/2/3-33 APL5501/2/3-33 1 3 Output Voltage (V) SHDN Threshold Voltage vs. Input Voltage +0 -10 0.9 -20 0.8 VIN=0V PSRR (dB) SHDN Threshold Voltage (V) 1.5 0.7 0.6 VIN=4V -30 -40 IOUT =50mA COUT=10uF CBP=0.1uF -50 -60 -70 0.5 VIN=5V -80 -90 0.4 3 3.5 4 4.5 5 5.5 -100 6 Input Voltage (V) Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 20 50 100 200 500 1k 2k 5k 10k 20k 50k 100k 200k Frequency (HZ) 7 www.anpec.com.tw APL5501/2/3 Typical Characteristics Output Noise Output Noise vs. Bypass Capacitor APL5501/2/3-33 100u 500 450 400 40u Output Noise (uV) VOUT (50uV/div) VIN=4.3V 80u IOUT =0mA COUT=10uF 60u CBP=0.1uF 20u 0 -20u -40u -60u 350 300 250 200 150 100 50 -80u -100u 0 0 4m 2m 6m 8m 10m 0 Time (s) 0.1 0.2 0.3 Bypass Capacitor (uF) Shutdown Exit Delay Shutdown Exit Delay APL5501/2/3-33 APL5501/2/3-33 3.3V 3.3V VOUT 0.4 VOUT CBP=10nF No Load CBP=100nF No Load 0V 0V 4V 4V vSHDN vSHDN 0V 0V Time (1ms/div) Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 Time (20ms/div) 8 www.anpec.com.tw APL5501/2/3 Typical Characteristics Region of Stable ESR vs. Load Current Entering Shutdown APL5501/2/3-33 APL5501/2/3-33 1 3.3V VOUT=3.3V VOUT COUT ESR () COUT=1F No Load 0V 4V 0.1 stable 0.01 unstable 0V 0.001 0 Time (200ms/div) 300 450 600 900 Line-Transient Response APL5901/2-33 APL5501/2/3-33 Output Voltage (20mV/div) 3.35 750 Load Current (mA) Output Voltage vs. Temperature 3.33 Output Voltage (V) 150 3.31 3.29 3.27 VIN 4V 3V VOUT 3.25 -40 0 40 80 120 Temperature (C ) Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 Time (40s/div) 9 www.anpec.com.tw APL5501/2/3 Typical Characteristics Load-Transient Response Output Voltage (50mV/div) APL5501/2/3-33 VOUT COUT=1F VIN=VOUT+1V IOUT=1mA~500mA Time (10s/div) Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 10 www.anpec.com.tw APL5501/2/3 Application Information Capacitor Selection and Regulator Stability Input-Output (Dropout)Voltage The minimum input-output voltage difference (dropout) determines the lowest usable supply voltage. In battery-powered systems, this will determine the useful end-of-life battery voltage. Because the APL5501/2/3 use a p-channel MOSFET pass transistor, the dropout voltage is a function of drain-to-source on-resistance (RDS(ON)) multiplied by the load current. The APL5501/2/3 use at least a 1uF capacitor on the input, and this capacitor can be Aluminum, Tantalum or Ceramic capacitor. The input capacitor with larger value and lower ESR provides better PSRR and linetransient response. The output capacitor also can use Aluminum, Tantalum or Ceramic capacitor, and a minimum value of 1uF and ESR above 0.06 is recommended. The curve of the stable region in typical characteristics shows the appropriate output capacitor ESR for different load current stable operation. A larger output capacitor can reduce noise and improve load-transient response, stability, and PSRR. Note that some ceramic dielectrics exhibit large capacitance and ESR variation with temperature. When using this capacitor, a minimum 10uF or more may be required to ensure the stability at low temperature operation. Use a bypass capacitor at BP pin for low output nvise. Increasing the capacitance will slightly decrease the output noise, but increase the start-up time. Reverse Current Protection The APL5501/2/3 have an internal reverse protection, it does not need an external schottky diode to connect the regulator input and output. If the output voltage is forced above the input voltage by more than 11mV, the IC will be shutdown and the ground pin current is below 0.1uA. Current Limit The APL5501/2/3 have a current limit protection. The ouptut voltage will drop close to zero volt, when load current reaches the limit, and then the load current will be limited at 150mA after output voltage is below 0.7V. When the load current back to the value where limiting started, the output voltage and current will return to normal value. When output is shorted to ground, the APL5501/2/3 will keep short circuit current at 150mA . Load-Transient Considerations The APL5501/2/3 load-transient response graphs in typical characteristics show the transient response. A step change in the load current from 0mA to 500mA at 1us will cause a 100mV transient spike. Larger output capacitor and lower ESR can reduce transient spike. Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 11 www.anpec.com.tw APL5501/2/3 Thermal Protection Thermal protection limits total power dissipation in the device. When the junction temperature exceeds TJ=+150J, the thermal sensor generates a logic signal to turn off the pass transistor and allows IC to cool. When the IC's junction temperature is down by 10J, the thermal sensor will turn the pass transistor on again, resulting in a pulsed output during continuous thermal protection. Thermal protection is designed to protect the APL5501/2/3 in the event of fault conditions. For continuous operation, do not exceed the absolute maximum junction temperature of TJ=+150J. Operating Region and Power Dissipation The thermal resistance of the case to circuit board, and the rate of air flow all control the APL5501/2/3's maximum power dissipation. The power dissipation across the device is PD = IOUT (VIN-VOUT) and the maximum power dissipation is: PDMAX = (TJ-TA) / (? JC + ? CA) where TJ-TA is the temperature difference between the junction and ambient air, ? JC is the thermal resistance of the package, and ? CA is the thermal resistance through the printed circuit board, copper traces, and other materials to the ambient air. The GND pin of the APL5501/3 provide an electrical connection to ground and channeling heat away. If power dissipation is large, connect the GND pin to ground using a large pad or ground plane, can improve the problem of over heat of IC. Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 12 www.anpec.com.tw APL5501/2/3 Packaging Information SOT-23-5 e1 5 4 E1 1 E 3 2 e b D A2 A a A1 Dim A A1 A2 D E E1 L L1 L2 N L2 L Mi ll imet er s Min . 0. 9 5 0. 0 5 0. 9 0 2. 8 2. 6 1. 5 0. 3 5 Inc hes Ma x . 1. 4 5 0. 1 5 1. 3 0 3. 0 0 3. 0 0 1. 7 0 0. 5 5 Min . 0. 0 37 0. 0 02 0. 0 35 0. 11 0 0. 1 02 0. 0 59 0. 0 14 0. 7 0. 0 20 10 0 0. 2 0 B SC 0. 5 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 Ma x . 0. 0 57 0. 0 06 0. 0 51 0. 11 8 0. 11 8 0. 0 67 0. 0 22 0. 0 08 B SC 5 0 L1 0. 0 28 5 13 10 www.anpec.com.tw APL5501/2/3 Packaging Information E e1 0.015X45 SOP-8 pin ( Reference JEDEC Registration MS-012) H e2 D A1 1 L 0.004max. Dim A Mi ll im et er s Inche s A Min . 1. 35 Max . 1. 75 Min. 0. 053 Max . 0. 069 A1 D E 0. 10 4. 80 3. 80 0. 25 5. 00 4. 00 0. 004 0. 189 0. 150 0. 010 0. 197 0. 157 H L e1 e2 5. 80 0. 40 0. 33 6. 20 1. 27 0. 51 0. 228 0. 016 0. 013 0. 244 0. 050 0. 020 1 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 1. 27B S C 0. 50B S C 8 8 14 www.anpec.com.tw APL5501/2/3 Packaging Information SOT-223( Reference JEDEC Registration SOT-223) D A B1 a c H E L K e A1 e1 b B Dim A A1 B B1 c D E e e1 H L K Millimeters Min. 1.50 0.02 0.60 2.90 0.28 6.30 3.30 Inches Max. 1.80 0.08 0.80 3.10 0.32 6.70 3.70 Min. 0.06 Max. 0.07 0.02 0.11 0.01 0.25 0.13 0.03 0.12 0.01 0.26 0.15 2.3 BSC 4.6 BSC 6.70 0.91 1.50 0 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 0.09 BSC 0.18 BSC 7.30 1.10 2.00 10 13 0.26 0.04 0.06 0 0.29 0.04 0.08 10 13 15 www.anpec.com.tw APL5501/2/3 Packaging Information SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62) D D1 a H 1 2 E 3 L C B1 B e e1 A a D im A B B1 C D D1 e e1 E H L M illim eters M in. 1.40 0.40 0.35 0.35 4.40 1.35 Inches M ax. 1.60 0.56 0.48 0.44 4.60 1.83 M in. 0.055 0.016 0.014 0.014 0.173 0.053 1.50 B SC 3.00 B SC 2.29 3.75 0.80 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 M ax. 0.063 0.022 0.019 0.017 0.181 0.072 0.059 BSC 0.118 B SC 2.60 4.25 1.20 10 16 0.090 0.148 0.031 0.102 0.167 0.047 10 www.anpec.com.tw APL5501/2/3 Packaging Information SOT-89-5 Dim A B C D E F G H I J K L M illim eters M in. 4.40 4.05 1.50 1.30 2.40 0.80 Inches M ax. 4.60 4.25 1.70 1.50 2.60 - M in. 0.17 0.16 0.06 0.05 0.09 0.03 3.00 REF 1.50 REF 0.40 1.40 0.35 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 M ax. 0.18 0.17 0.07 0.06 0.1 0.12 REF 0.06 REF 0.52 1.60 0.41 5 TYP 0.01 0.05 0.01 0.02 0.06 0.02 0.2 TYP 17 www.anpec.com.tw APL5501/2/3 Packaging Information TO-252( Reference JEDEC Registration TO-252) E A b2 C1 L2 D H L1 L b C e1 Dim A A1 Mi ll im et er s Inc he s Min . Ma x . Min . Ma x . 2. 1 8 2. 3 9 0. 0 86 0. 0 94 A1 0. 8 9 1. 2 7 0. 0 35 0. 0 50 b 0. 5 08 0. 8 9 0. 0 20 0. 0 35 b2 5. 2 07 5. 4 61 0. 2 05 0. 2 15 C 0. 4 6 0. 5 8 0. 0 18 0. 0 23 C1 0. 4 6 0. 5 8 0. 0 18 0. 0 23 D 5. 3 34 6. 2 2 0. 2 10 0. 2 45 E 6. 3 5 6. 7 3 0. 2 50 0. 2 65 e1 3. 9 6 5. 1 8 0. 1 56 0. 2 04 H 9. 3 98 10 . 41 0. 3 70 0. 4 10 L 0. 5 1 L1 0. 6 4 1. 0 2 0. 0 25 0. 0 40 L2 0. 8 9 2. 0 32 0. 0 35 0. 0 80 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 0. 0 20 18 www.anpec.com.tw APL5501/2/3 Packaging Information TO-252-5 H A J D M C B K L S Dim A B C D P S H J K L M P Millimeters Min. 6.40 5.20 6.80 2.20 Inches Max. 6.80 5.50 7.20 2.80 Min. 0.25 0.20 0.26 0.08 1.27 REF Max. 0.26 0.21 0.27 0.11 0.05 REF 0.50 2.20 0.45 0 0.90 5.40 0.80 2.40 0.55 0.15 1.50 5.80 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 19 0.02 0.08 0.01 0 0.03 0.21 0.03 0.09 0.02 0.006 0.06 0.22 www.anpec.com.tw APL5501/2/3 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) temperature Reference JEDEC Standard J-STD-020A APRIL 1999 Peak temperature 183C Pre-heat temperature Time Classification Reflow Profiles Convection or IR/ Convection Average ramp-up rate(183C to Peak) 3C/second max. 120 seconds max Preheat temperature 125 25C) 60 - 150 seconds Temperature maintained above 183C Time within 5C of actual peak temperature 10 -20 seconds Peak temperature range 220 +5/-0C or 235 +5/-0C Ramp-down rate 6 C /second max. 6 minutes max. Time 25C to peak temperature VPR 10 C /second max. 60 seconds 215-219C or 235 +5/-0C 10 C /second max. Package Reflow Conditions pkg. thickness 2.5mm and all bgas Convection 220 +5/-0 C VPR 215-219 C IR/Convection 220 +5/-0 C pkg. thickness < 2.5mm and pkg. volume 350 mm Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 20 pkg. thickness < 2.5mm and pkg. volume < 350mm Convection 235 +5/-0 C VPR 235 +5/-0 C IR/Convection 235 +5/-0 C www.anpec.com.tw APL5501/2/3 R e lia b ilit y te s t p r o g r a m Te s t ite m S O L D E R A B IL IT Y H O LT PCT TST ESD L a tc h -U p M e th o d M IL -S T D -8 8 3 D -2 0 0 3 M IL -S T D -8 8 3 D -1 0 0 5 .7 J E S D -2 2 - B , A 1 0 2 M IL -S T D -8 8 3 D -1 0 11 .9 M IL -S T D -8 8 3 D -3 0 1 5 .7 JESD 78 D e s c rip tio n 2 45 C , 5 S E C 1 0 0 0 H rs B ia s @ 1 2 5 C 1 6 8 H rs , 1 0 0 % R H , 1 2 1 C -6 5 C ~ 1 5 0 C , 2 0 0 C y c le s V H B M > 2 K V, V M M > 2 0 0 V 1 0 m s , I tr > 1 0 0 m A Carrier Tape t D P Po E P1 Bo F W Ko Ao D1 T2 J C A B T1 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 21 www.anpec.com.tw APL5501/2/3 Reel Dimensions A p p lic a tio n SOP- 8 A p p lic a tio n S O T -8 9 A p p lic a tio n S O T -2 2 3 A p p lic a tio n T O -2 5 2 A B C J T1 T2 W P E 330 1 6 2 + 1.5 1 2 .7 5 + 0 .15 2 0.5 1 2 .4 0 .2 2 0.2 12 0. 3 8 0 .1 1 .75 0 .1 F D D1 Po P1 Ao Bo Ko t 5 .5 1 1 .55 + 0 .1 1 .55 + 0 .2 5 4 .0 0 .1 2 .0 0 .1 6 .4 0 .1 5 .2 0 . 1 2 .1 0 .1 0 .3 0 .01 3 A B C J T1 T2 E 70 2 1 3 .5 0.1 5 3 0 .1 5 14 2 1 .3 0 .3 W 1 2 + 0.3 1 2 - 0 .1 P 178 1 8 0 .1 1 .7 5 0 .1 F D D1 Po P1 Ao Bo Ko t 5 .5 0 .0 5 1 .5 0 .1 1 .5 0 .1 4 .0 0 .1 2 .0 0 .1 4 .8 0 .1 4 .5 0 .1 1 .8 0 0 .1 0 .3 0 .01 3 A B J T1 T2 W P E 3301 6 2 1 .5 C 1 2 .7 5 0 .1 5 2 0 .6 1 2 .4 +0 .2 2 0 .2 1 2 0 .3 8 0 .1 1 .7 5 0 .1 F D D1 Po P1 Ao Bo Ko t 5 .5 0 .0 5 1 .5 + 0.1 1 .5 + 0.1 4 .0 0 .1 2 .0 0 .0 5 6 .9 0 .1 7 .5 0 .1 2 .1 0 .1 0 .3 0 .05 T2 A B C J 13 0. 5 2 0 .5 2 .5 0 .5 W 1 6 + 0 .3 - 0 .1 E 100 2 T1 1 6 .4 + 0 .3 -0 .2 P 330 3 8 0 .1 1 .7 5 0 .1 F D D1 Po P1 Ao Bo Ko t 7 .5 0 .1 1 .5 + 0.1 1 .5 0 .25 4 .0 0 .1 2 .0 0 .1 6 .8 0 .1 1 0 .4 0 .1 2 .5 0 .1 0 .3 0 .05 Cover Tape Dimensions Application SOP- 8 SOT- 89 SOT- 223 TO- 252 Carrier Width 12 12 12 16 Cover Tape Width 9.3 9.3 9.3 13.3 Devices Per Reel 2500 1000 2500 2500 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.9 - May., 2003 22 www.anpec.com.tw