OP290AB - Optek Technologies, Inc.

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 1 of 8

Plastic Infrared Emitting Diode

OP290 Series

Description:

Each device in this series, is a gallium aluminum arsenide infrared Light Emitting Diode (LED) that is molded in an

IR-transmissive package with a wavelength centered at 890 nm, which closely matches the spectral response of

silicon phototransistors, except for OP298 (AA, AB, AC, AD), which has either an 850 nm or 875 nm center

wavelength. For identification purposes, each LED anode lead is longer than the cathode lead. Package T-1¾

devices include: OP290, OP291, OP292, OP294, OP295, OP296, OP297, OP299 (A, B, C) and OP297FAB,

Plastic Package TO-18 or TO-46 devices include: OP293 and OP298 (A, B, C, AA, AB, AC, AD).

Each OP290, OP291 and OP292 series come in three electrical parameters options A, B and C. The OP290

series forward current is specified under pulse conditions up to 1.5 amps, the OP291 series forward current is

specified under pulse conditions up to 100 milliamps and the OP292 series forward current is specified under

pulse conditions up to 1 amp. The Cathode Lead length is 0.06” (1.52 mm) shorter than the Anode Lead. The

silver-copper lead frame offers excellent thermal characteristics.

Each OP293 and OP298 series come in three electrical parameter options A, B and C. The OP293 series has an

included emission angle of 60° while the OP298 series has an included emission angle of 25°. The Cathode Lead

length is 0.06” (1.52 mm) shorter than the Anode Lead. These devices, which come in a variety of power ranges

offering a low cost replacement for TO-18 or TO-46 hermetic packages.

Each OP298 series come with a high irradiance output versions with four electrical parameter options AA, AB, AC

and AD. These power options are in the range of 5X greater than the A, B or C options. The OP298 series has an

included emission angle of 25°. The Cathode Lead length is 0.06” (1.52 mm) shorter than the Anode Lead. These

devices, which come in a variety of power ranges offering a low cost replacement for TO-18 or TO-46 hermetic

packages.

OP294 and OP299 are designed for low-current or power-limited applications, such as battery supplies. They are

similar to the OP290 and OP295, but use a smaller chip that increases output efficiency at low current levels by

increasing current density. Light output can be maximized with continuous (D.C.) forward current up to 100 mA or

with pulsed forward current up to 750 mA. The Cathode Lead length is 0.06” (1.52 mm) shorter than the Anode

Lead.

Each OP295, OP296 and OP297 series come in three electrical parameters options A, B and C. The OP295

series forward current is specified under pulse conditions up to 5 amps, the OP296 series forward current is

specified under pulse conditions up to 2 amps and the OP297 series forward current is specified under pulse

conditions up to 1 amp. The Cathode Lead length is 0.06” (1.52 mm) shorter than the Anode Lead. The

OP297FAB has a reversed polarity from the OP297A, B or C. The silver-copper lead frame offers excellent

thermal characteristics.

All of these devices are spectrall y and mechanically matched to the OP593 and OP598 series phototransistors.

Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data.

• Machine automation

• Machine safety

• End of travel sensor

Applications:

• Non-contact reflective

object sensor

• Assembly line

automation

• Door sensor

• Battery-operated

applications

Features:

• Choice of narrow or wide irradiance pattern

• Choice of power ranges

• Choice of T-1¾, TO-18 or T-46 package

• Higher power output than GaAs at equivalent LEDs

RoHS

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 2 of 8

Plastic Infrared Emitting Diode

OP290 Series

TO-18, TO-46 Package

OP293 & OP298

Part Number Guide — OP290 - OP299 Series

OP 2 9 X X W

Optek Assembly

Photodiode Output Family

Maximum Forward Current Electrical Specification Variations:

0, 5 — 5 amps A — Parameter A

1, 6 — 2 amps B — Parameter B

2, 7 — 1 amps C — Parameter C

3, 8 — 200 milli-amps D — Parameter D

4, 9 — 750 milli-amps AA — Parameter BA

AB — Parameter BB

AC — Parameter BC

AD — Parameter BD

T-1¾ Package

OP290, OP291, OP292, OP294,

OP295, OP296, OP297, OP299

Electrical Connection

A, B, C, AA, AB, AC, AD

Pin #

LED

X=0.060” (1.52 mm)

1 Anode

2 Cathode

INCHES

[MILLIMETERS]

DIMENSIONS ARE IN:

Pin #

LED

X=0.060” (1.52 mm)

1 Anode

2 Cathode

Electrical Connection A, B, C, D

Pin #

LED

X=0.060” (1.52 mm)

1 Cathode

2 Anode

Electrical Connection OP297AB

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 3 of 8

Plastic Infrared Emitting Diode

OP290 Series

Notes:

1. For OP290, OP291, OP292, OP295, OP296 and OP297, refer to graph of Maximum Peak Pulse Current vs Pulse Width.

2. For all OPs in this series, RMA flux is recommended. Duration can be extended to 10 second maximum when soldering. A

maximum of 20 grams force may be applied to the leads when flow soldering.

3. For OP290, OP291, OP292, OP295, OP296 and OP297, measured in free-air. Derate linearly 3.33 mW/° C above 25° C.

4. For OP290, OP291and OP292, mounted on 1/16” (1.6 mm) thick PCBoard with each lead soldered through 80 mil square lands

0.250” (6.35 mm) below flange of device. Derate linearly 5.33 mW/°C above 62.5°. For OP293 and OP298, mounted on 1/16” (1.60

mm) thick PCBoard with each lead soldered through 80 mil square lands 0.250” (6.35 mm) below flange of device. Derate power

dissipation linearly 2.00 mW/°C above 25° C (normal use). For OP295, OP296 and OP297, mounted on 1/16” (1.6 mm) thick

PCBoard with each lead soldered through 80 mil square lands 0.250” (6.35 mm) below flange of device. Derate linearly 5.33 mW/°C

above 25° C.

5. Immersed in silicone fluid to simulate infinite heat sink. For OP290, OP291 and OP292, derate linearly 11.1 mW/°C above 95°C. For

OP293 and OP298, derate power dissipation linearly 2.50 mW/° C above 25° C. For OP295, OP296 and OP297, derate linearly 11.1

mW/° C above 25° C.

Absolute Maximum Ratings (TA=25°C unless otherwise noted)

Storage and Operating Temperature Range -40o C to +100o C

Reverse Voltage

OP290, OP292, OP294, OP295, OP297, OP299

OP291, OP293, OP296, OP298

5.0 V

2.0 V

Continuous Forward Current

OP290, OP291, OP292

OP294, OP295, OP299

OP295, OP296, OP297

150 mA(1)

100 mA(1)

150 mA(1)

Continuous Forward Current, OP293, OP298

Free Air

Board Mounted

Full Heat Sink

100 mA

133 mA

200 mA

Peak Forward Current

OP290, OP295 (25 µs pulse width)

OP291, OP296 (100 µs pulse width)

OP292, OP297 (100 µs pulse width)

OP293, OP298 (25 µs pulse width)

OP294, OP299

5.0 A

2.0 A

1.00 A

2.0 A

750 mA

Notes:

1. For OP290, OP291, OP292, OP295, OP296 and OP297, derate linearly 1.67 mA/° C above 25° C (free-air). When used with heat

sink (see note 5), derate linearly 2.07 mA/° C above 65° C (normal use). For OP293 and OP298, when measured in free-air, derate

power dissipation linearly 1.43 mW/° C above 25° C. For OP294 and OP299, derate linearly 1.80 mW/° C above 25° C.

Absolute Maximum Ratings (TA=25°C unless otherwise noted)

Maximum Duty Cycle

OP290 (25 µs pulse width @ 5 A)

1.25%(1)

Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C(2)

Power Dissipation, Free Air

OP290, OP291, OP292, OP295, OP296, OP297

OP293, OP298

Power Dissipation, Board Mounted

OP290, OP291, OP292, op295, OP296, OP297

OP293, OP298

Power Dissipation, Full Heat Sink

OP290, OP291, OP292, OP295, OP296, OP297

OP293, OP298

333 mW(3)

142 mW(3)

533 mW(4)

200 mW(4)

1.11 W(5)

400 mW(5)

Power Dissipation

OP294, OP299

180 mW

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 4 of 8

Plastic Infrared Emitting Diode

OP290 Series

Notes:

1. Measurement is taken at the end of a single 100 µs pulse. Heating due to increased pulse rate or pulse width will cause a decrease

in reading.

2. Measurement of the average apertured radiant energy incident upon a sensing area 0.250” (6.35 mm) in diameter perpendicular to

and centered on the mechanical axis of the lens and the specified distance from the end of the device. On all models in this series,

EE(APT) is not necessarily uniform within the measured area.

3. Measurement is taken at the end of a single 10 ms pulse. Heating due to increased pulse rate or pulse width will cause a decrease in

reading.

Electrical Characteristics (TA = 25°C unless otherwise noted)

SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS

Input Diode

EE (APT)

(2)

Apertured Radiant Incidence

OP290A

OP290B

OP290C

210

180

150

300

IF = 1.50 A(1)(2)

Measured into a 0.250” [6.35mm] aperture

0.2” (5.08 mm) from the tip of the lens.

OP291A

OP291B

OP291C

IF = 100 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

0.2” (5.08 mm) from the tip of the lens.

OP292A

OP292B

OP292C

2.7

2.2

1.7

3.6

4.4

IF = 20 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

0.2” (5.08 mm) from the tip of the lens.

OP293A

OP293B

OP293C

IF = 100 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

0.2” (5.08 mm) from the tip of the lens.

OP294 0.50 - 1.50

IF = 5 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

0.200” (5.08mm) from the tip of the lens.

OP295A

OP295B

OP295C

IF = 1.50 A(1)(2)

Measured into a 0.250” [6.35mm] aperture

1.129” (28.7 mm) from the tip of the lens.

OP296A

OP296B

OP296C

3.6

2.6

1.6

6.6

IF = 100 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

1.129” (28.7 mm) from the tip of the lens.

OP297FAB

OP297A

OP297B

OP297C

2.4

0.7

0.5

0.3

1.0

1.3

IF = 20 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

1.129” (28.7 mm) from the tip of the lens.

OP298A

OP298B

OP298C

3.0

2.4

1.8

4.8

IF = 100 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

0.2” (5.08 mm) from the tip of the lens.

OP298AA

OP298AB

OP298AC

OP298AD

3.5

6.5

8.5

11.5

IF = 100 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

1.129” (28.7 mm) from the tip of the lens.

OP299 0.15 - 0.45

IF = 100 mA(1)(2)

Measured into a 0.250” [6.35mm] aperture

1.129” (28.7 mm) from the tip of the lens.

mW/cm2

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 5 of 8

Plastic Infrared Emitting Diode

OP290 Series

Electrical Characteristics (TA = 25°C unless otherwise noted)

SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS

Input Diode

Forward Voltage(3)

OP290, OP295

OP291, OP296

OP292, OP297, OP297FAB

OP293, OP298 (A, B, C)

OP298 (AA, AB, AC, AD)

OP294, OP299

4.00

2.00

1.75

2.00

1.50

IF = 1.50 A

IF = 100 mA

IF = 20 mA

IF = 1.50 A

IF = 100 mA

IF = 5 mA

Reverse Current(3)

OP290, OP292

OP291, OP293, OP298 (A, B, C), OP296

OP298 (AA, AB, AC, AD)

OP294, OP299

OP295, OP297

OP297FAB

100

µA

VR= 5 V

VR= 2 V

VR= 5 V

λP

Wavelength at Peak Emission

OP290, OP291, OP292, OP293, OP294,

OP295, OP296, OP297, OP298 (A, B, C),

OP299

OP297FAB, OP298 (AA, AB, AC, AD)

890

875

nm IF = 10 mA

B Spectral Bandwidth between Half Power

Points - 80 - nm IF = 10 mA

∆λP /∆T Spectral Shift with Temperature - +0.18 - nm/°C IF = Constant

θHP

Emission Angle at Half Power Points

OP290, OP291, OP292, OP294

OP293

OP295, OP296, OP297, OP299

OP298

Degree

IF = 20 mA

tr Output Rise Time - 500 - ns IF(PK)=100 mA, PW=10 µs, and

D.C.=10.0%

tf Output Fall Time - 250 - ns

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 6 of 8

Plastic Infrared Emitting Diode

OP290 Series

Forward Voltage vs Forward Current vs Temp.

0.8

1.0

1.2

1.4

1.6

1.8

0 102030405060708090100

Forward Current (mA)

Forward Voltage (V)

-40° C

-20° C

0° C

20° C

40° C

60° C

80°C

100°C

OP290, OP291, OP292, OP293, OP294, (A, C)

Optical Power vs Forward Current vs Temperature

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0 102030405060708090100

Forward Current (mA)

Relative Output Power

-40° C

-20° C

0° C

20° C

40° C

60° C

80° C

100°C

Normalized at 50 mA and 20°C

Distance vs Output Power vs Forward Current

0.2 '' 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 ''

Distance (inches)

Normalized Output Power

10 mA

20 mA

30 mA

40 mA

50 mA

60 mA

70 mA

80 mA

90 mA

100 mA

Normalized at 1" and 50 m

Forward Current

Relative Radiant Intensity vs. Angular

Displacement

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

-80 -60 -40 -20 0 20 40 60 80

Angular Displacement (Degrees)

Relative Radiant Intensity

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 7 of 8

Plastic Infrared Emitting Diode

OP290 Series

OP295, OP296, OP297, OP298, OP299

Forward Voltage vs Forward Current vs Temp.

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

0 102030405060708090100

Forward Current (mA)

Typical Forward Voltage (V)

-60° C

-40° C

-20° C

0° C

20° C

40° C

60° C

80° C

100° C

120°C

Optical Power vs I

vs Temperature

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0 102030405060708090100

Forward Current I

(mA)

Normalized Optical Power

-60° C

-40° C

-20° C

0° C

20° C

40° C

60° C

80° C

100° C

120° C

Normalized at 50 mA and 20° C

Distance vs Output Power vs Forward Current

0.2 '' 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 ''

Distance (inches)

Normalized Output Power

10 mA

20 mA

30 mA

40 mA

50 mA

60 mA

70 mA

80 mA

90 mA

100 mA

Normalized at 1" and 50 m

Forward Current

Relative Radiant Intensity vs. Angular

Dis place m ent

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

-40-30-20-100 10203040

Angular Displacement (Degrees)

Relative Radiant Intensity

OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C 03/2012

Page 8 of 8

Plastic Infrared Emitting Diode

OP290 Series

OP290A/OP593 and OP295/OP598 - Coupling Characteristics

Coupling Characteristics

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0.00.51.01.52.02.53.0

Lens Tip Separation (inches)

Normalized Collector Current (mA)

OP290A

OP295

Test Conditions:

OP290 & OP295 I

= 1.5A, PW = 100µs, Duty Cycle = 0.1%

OP593 & OP598 V

= 5V, R

= 1kΩ, T

= 25°C