MAX7461 Loss-of-Sync Alarm General Description The MAX7461 single-channel loss-of-sync alarm (LOS) provides composite video sync detection in NTSC, PAL, and SECAM standard-definition television (SDTV) systems. The MAX7461's advanced detection circuitry delivers robust performance by preventing false lossof-sync alarms due to noise. The device accepts an AC-coupled composite (CVBS), luma (Y), or any other video signal with sync, and outputs a logic-level signal. The open-drain LOS output is low when no sync is detected and high impedance when sync is detected. The device operates from a single +5V supply. The MAX7461 is available in a 5-pin SOT23 package and is specified for operation over the -40C to +85C temperature range. Features Accepts CVBS, Y, or Any Other Video with Sync Loss-of-Sync Alarm Output Robust Performance in Noisy Environments Wire-OR Alarm Output NTSC, PAL, and SECAM Small 5-Pin SOT23 Package Pin Configuration TOP VIEW IN Applications Security Systems 1 GND 2 5 VCC 4 LOS MAX7461 Consumer Electronics GND 3 Ordering Information PART TEMP RANGE PINPACKAGE MAX7461EUK -40C to +85C 5 SOT23 SOT23 PACKAGE CODE U5-2 Functional Diagram +5V 0.1F VCC 5 VCC SYNC SLICE LEVEL CIN 0.1F IN 1 CLAMP LPF MAX7461 RO 1k SYNC DETECTOR SYNC LOS FILTER LOS 4 75 GND 3 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. 19-0553; Rev 1; 4/13 MAX7461 Loss-of-Sync Alarm ABSOLUTE MAXIMUM RATINGS VCC to GND ..............................................................-0.3V to +6V LOS to GND..............................................................-0.3V to +6V IN to GND.................-0.3V to the lower of +6V and (VCC + 0.3V) Continuous Power Dissipation (TA = +70C) 5-Pin SOT23-5 (derate 7.1mW/C above +70C) ......571.0mW Maximum Current Into Any Pin .........................................50mA Operating Temperature Range MAX7461EUK ...................................................-40C to +85C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Junction Temperature ......................................................+150C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = +4.5V to +5.5V, GND = 0, CIN = 0.1F, RO = 500, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 105 130 mVP-P AC CHARACTERISTICS Minimum Input Sync Height VIN-MIN AC-coupled (Note 1) Maximum Input Voltage VIN-MAX AC-coupled 2.4 VP-P LOS Release Time tRT (Note 2) 1.7 2.2 2.7 LOS Detect Time tDT (Note 3) 1.9 3.4 4.9 VOL ISINK = 10mA ms DIGITAL CHARACTERISTICS Output Low Voltage Logic High Leakage Current IOLEAK 0.4 V 1 A POWER REQUIREMENTS Supply Voltage VCC Supply Current ICC Power-Supply Noise Immunity VPSNI 4.5 0 to 5MHz sinusoid on VCC (Note 4) 5.0 5.5 V 1.7 2.2 mA 200 mVP-P Note 1: Minimum input sync height is the voltage above which LOS is guaranteed to be in high-impedance mode after the maximum LOS time-constant time. Note 2: LOS release time is the time that the video input must be continuously present before LOS goes high (inactive state). Note 3: The LOS detect time is the time that the video input must be continuously absent before LOS goes low (active state). Note 4: The MAX7461 LOS output is accurate with a power-supply noise level below VPSNI. 2 Maxim Integrated MAX7461 Loss-of-Sync Alarm Typical Operating Characteristics (VCC = 5V, GND = 0, CIN = 0.1F, RO = 10k, TA = +25C, unless otherwise noted.) LOS RELEASE TIME vs. SUPPLY VOLTAGE LOS DETECT TIME vs. SUPPLY VOLTAGE MAX7461 toc01 4.0 MAX7461 toc02 3.0 3.5 TIME (ms) LOS 5V/div TIME (ms) 2.5 IN 500mV/div 2.0 3.0 2.5 1.5 2.0 1.0 t = 10ms/div MAX7461 toc03 CVSB LOS ALERT TRANSIENT 4.5 4.7 4.9 5.1 5.3 4.5 5.5 4.7 5.5 1.9 ICC (mA) SYNC HEIGHT (V) 5.3 MAX7461 toc05 MAX7461 toc04 2.0 0.15 0.10 1.8 1.7 0.05 1.6 0 4.5 4.7 4.9 5.1 SUPPLY VOLTAGE (V) Maxim Integrated 5.1 SUPPLY CURRENT vs. TEMPERATURE (CVBS INPUT) SYNC HEIGHT LOS ALERT THRESHOLD vs. SUPPLY VOLTAGE 0.20 4.9 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) 5.3 5.5 -40 -20 0 20 40 60 80 TEMPERATURE (C) 3 MAX7461 Loss-of-Sync Alarm Pin Description PIN NAME FUNCTION 1 IN 2, 3 GND Ground 4 LOS Loss-Of-Sync Output (Open Drain). LOS is in high impedance when sync pulses are detected, and is pulled low when no horizontal sync signal is detected for more than the LOS detect time. LOS returns high when sync pulses are detected for more than the LOS release time. Connect a 1k pullup resistor from LOS to VCC. 5 VCC Power-Supply Input. Bypass to GND with a 0.1F capacitor. Video Input. Accepts CVBS, luma (Y), or any video input with sync. AC-couple IN with a series 0.1F capacitor. Detailed Description Applications Information The MAX7461 single-channel LOS alarm is ideal for any video system needing to verify the presence of a video source. The device accepts an AC-coupled CVBS, Y, or any video signal with sync, and pulls LOS low when no composite sync signal is detected for more than the LOS detect time (3.4ms, typ) at the input (IN). Use 0.1F ceramic capacitors to AC-couple the input. The input cannot be DC-coupled. The input capacitor stores a DC level so that the video signal is clamped to an appropriate DC voltage for proper sync detection. Clamp The MAX7461 features an input clamp that corrects any DC shift, on a line-by-line basis. The external AC-coupling capacitor provides DC isolation for the input. Lowpass Filter The MAX7461 integrates a lowpass filter for enhanced sync detection. The lowpass filter prevents false sync detection by reducing color burst, chroma, and noise. Sync Detector/LOS Filter The sync detector looks for sync pulses greater than the minimum sync voltage (0.13VP-P). If the detector does not detect any sync pulses for 3.4ms (typ), the LOS filter pulls LOS low. After detecting sync for at least 2.2ms (typ), the LOS filter returns LOS to a highimpedance state. LOS is an open-drain output. Connect a 1k pullup resistor between LOS and VCC. Input Considerations Power-Supply Bypassing Careful PC board layout is important for optimal system performance. Do not use wire-wrapped boards or breadboards. When possible, use a multilayer board with a dedicated low-inductance ground plane and supply plane. Connect all GND inputs to a single ground plane and V CC to a single-supply plane. Bypass VCC to GND with a 0.1F capacitor. Wired-OR Application The LOS open-drain output allows the MAX7461 to be used in wired-OR applications as shown in the typical application diagram of Figure 1. Chip Information PROCESS: BiCMOS Power-On Reset (POR) At power-up, LOS is pulled low and the MAX7461 checks for 2.2ms (typ) of valid sync pulses before releasing LOS. LOS remains high impedance while a valid sync signal is detected at the input. 4 Maxim Integrated MAX7461 Loss-of-Sync Alarm VCC 1k C MAX7461 0.1F TV TUNER MONITOR 1 75 MAX7461 0.1F RGB VIDEO SOURCE SWITCH MATRIX AND PROCESSING 75 MONITOR N MAX7461 0.1F CAMERA 75 Figure 1. Wired-OR System Maxim Integrated 5 MAX7461 Loss-of-Sync Alarm VCC 1k 1 C N MAX7461 0.1F CAM 1 MONITOR 1 VCC 75 1k MAX7461 0.1F CAM 2 VCC SWITCH MATRIX AND PROCESSING 75 MONITOR N 1k MAX7461 0.1F CAM N 75 Figure 2. Video Security System Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. 6 PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 5 SOT23 U5-2 21-0057 90-0174 Maxim Integrated MAX7461 Loss-of-Sync Alarm Revision History REVISION NUMBER REVISION DATE 0 6/00 Initial release 1 4/13 Removed references for automotive applications DESCRIPTION PAGES CHANGED -- 1, 4, 5 Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 (c) 2013 Maxim Integrated Products, Inc. 7 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX7461EUK+T