ASM03P100 - Cutting Edge Optronics, Inc.

SILVER BULLETTM

OPTICAL

PARAMETER CONDITIONS MIN TYP MAX UNITS

CHARACTERISTICS

QCW Peak Power Output 65A, 150 µsec, 1kHz (1) 100 --- --- W

Operating Current at 25˚C Heat Sink100W --- 55 65 A

Threshold Current 25˚C Heat Sink --- 13 16 A

Slope Efficiency 25˚C Heat Sink 2.0 2.2 --- W/A

Efficiency 100W at 25˚C Heat Sink 40 45 --- %

Number of Emitters --- --- 72 x 2 ---

Emitter Size --- --- 90 x 1 --- µm

Emitter Pitch --- --- 133 --- µm

Center Wavelength 100W at 25˚C Heat Sink 792 808 812 nm

Wavelength Tolerance 100W at 25˚C Heat Sink ± 1 ± 3 ± 4 nm

Spectral Width 100W at 25˚C Heat Sink --- 2.0 2.5 nm

Wavelength Shift --- --- 0.25 0.27 nm/˚C

Beam Divergence FWHM --- --- 40x10 42x12 ˚ x ˚

Polarization --- --- TE --- ---

Degradation Rate (2) 25˚C Heat Sink --- 5 --- %/G shots

ELECTRICAL

PARAMETER CONDITIONS MIN TYP MAX UNITS

CHARACTERISTICS

Built-in Voltage 25˚C Heat Sink --- 3.2 3.4 V

Series Resistance 25 ˚C Heat Sink --- 0.012 0.020 ohms

Operating Voltage 25˚C Heat Sink, 70W --- 3.8 5.4 V

NOTES

(1) Lower beam divergence is also available.

100W QCW Laser Diode Array Submodule

Part Number: ASM03P100

(1)

(2)

· Packaged 2 Bar Laser

Diode Array

· Easily Soldered to a

Heat Exchanger

· Available Wavelengths

(785-1064nm)

Typical degradation rates are 5% in the first 10 million shots and 5% per billion shots thereafter.

U.S. Patent Numbers: 5,734,672 5,913,108

Cutting Edge Optronics ·20 Point West Blvd. ·St. Charles, MO 63301

636.916.4900 ·636.916.5665 fax ··www.ceolaser.com

ABSOLUTE MAXIMUM

PARAMETER CONDITIONS

RATINGS

Forward Current 70A

Reverse Current 25µA

Reverse Voltage 3V

Operating Temperature Range (3) -20˚C to 50˚C

Storage Temperature Range -40˚C to 85˚C

MECHANICAL

PARAMETER DIMENSIONS

CHARACTERISTICS

Package Length 0.250 ± 0.001 inches

Package Width 0.394 ± 0.001 inches

Package Height 0.065 ± 0.003 inches

Package Weight 0.6g

Package Thermal Resistance 0.4˚C/W

NOTES

(3) A dry nitrogen environment should be provided by the user when storing and operating at tempera-

tures below ambient dew point.

REV D-10/01

Cutting Edge Optronics reserves the right to change product

design and specification at any time without notice.

No license is granted by implication or otherwise under any patents or

patent rights of Cutting Edge Optronics or others.

No responsibility is assumed for the use of these products, nor for any in-

fringement on the rights of others resulting from the use of these products.

Laser diode product components are intended for use in a user-

devised end system.However, these products are capable of emitting

Class IV radiation. Extreme care must be exercised during their oper-

ation. Only persons familiar with the appropriate safety precautions

should operate a laser product. Directly viewing the laser beam or

exposure to specular reflections must be avoided. Serious injury may

result if any part of the body is exposed to the beam. The eye is

extremely sensitive to the infrared r adiation and therefore, proper eye-

wear must be worn at all times. Use of optical instr uments with these

products may increase e ye hazard.Alwa ys wear proper e ye protection

when operating.

Diode laser

CLASS IV

5W 635-1000nm

AVOID EYE OR SKIN EXPOSURE TO DIRECT

OR SCATTERED RADIATION.

INVISIBLE LASER

RADIATION

.394 [10,01]

.250 [6,35]

.15

[3,81] .12

[3]

.025 [0,64]

SOLDER PADS

FOR ELECTRICAL

LEADS METALIZED BeO SPACER

ENDBLOCK

DIODE BAR

2 PLACES

.065

[1,65]

.099 [2,51]

.047 [1,19]

.06 [1,5]

Cutting Edge Optronics ·20 Point West Blvd. ·St. Charles, MO 63301

636.916.4900 ·636.916.5665 fax ··www.ceolaser.com