256-Position One-Time Programmable
Dual-Channel I2C Digital Potentiometers
AD5172/AD5173
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.326.8703 © 2003 Analog Devices, Inc. All rights reserved.
FEATURES
2-channel, 256-position
OTP (one-time programmable) set-and-forget resistance
setting, low cost alternative to EEMEM
Unlimited adjustments prior to OTP activation
OTP overwrite allows dynamic adjustments with user
defined preset
End-to-end resistance: 2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ
Compact MSOP-10 (3 mm × 4.9 mm) package
Fast settling time: tS = 5 µs typ in power-up
Full read/write of wiper register
Power-on preset to midscale
Extra package address decode pins AD0 and AD1 (AD5173)
Single supply 2.7 V to 5.5 V
Low temperature coefficient: 35 ppm/°C
Low power, IDD = 6 µA max
Wide operating temperature: –40°C to +125°C
Evaluation board and software are available
Software replaces µC in factory programming applications
APPLICATIONS
Systems calibration
Electronics level setting
Mechanical Trimmers® replacement in new designs
Permanent factory PCB setting
Transducer adjustment of pressure, temperature, position,
chemical, and optical sensors
RF amplifier biasing
Automotive electronics adjustment
Gain control and offset adjustment
GENERAL OVERVIEW
The AD5172/AD5173 are dual channel, 256-position, one-time
programmable (OTP) digital potentiometers1 that employ fuse
link technology to achieve memory retention of resistance
setting. OTP is a cost-effective alternative to EEMEM for users
who do not need to program the digital potentiometer setting in
memory more than once. This device performs the same elec-
tronic adjustment function as mechanical potentiometers or
variable resistors with enhanced resolution, solid-state reliabil-
ity, and superior low temperature coefficient performance.
The AD5172/AD5173 are programmed using a 2-wire, I2C
compatible digital interface. Unlimited adjustments are allowed
before permanently setting the resistance value. During OTP
activation, a permanent blow fuse command freezes the wiper
position (analogous to placing epoxy on a mechanical trimmer).
FUNCTIONAL BLOCK DIAGRAMS
A1
V
DD
G
ND
SDA
SCL
W1
RDAC
REGISTER 1
SERIAL INPUT
REGISTER
04103-0-001
B1 A2 W2
RDAC
REGISTER 2
B2
FUSE
LINKS
12
/
8
Figure 1. AD5172
V
DD
G
ND
SDA
SCL
AD0
AD1
W1
RDAC
REGISTER 1
ADDRESS
DECODE
SERIAL INPUT
REGISTER
B1 W2
RDAC
REGISTER 2
B2
FUSE
LINKS
12
/
8
04103-0-002
Figure 2. AD5173
Unlike traditional OTP digital potentiometers, the AD5172/
AD5173 have a unique temporary OTP overwrite feature that
allows for new adjustments even after the fuse has been blown.
However, the OTP setting is restored during subsequent power-
up conditions. This feature allows users to treat these digital
potentiometers as volatile potentiometers with a programmable
preset.
For applications that program the AD5172/AD5173 at the
factory, Analog Devices offers device programming software
running on Windows® NT®, 2000, and XP® operating systems.
This software effectively replaces any external I2C controllers,
thus enhancing the time-to-market of the user’s systems.
1The terms digital potentiometer, VR, and RDAC are used interchangeably.
AD5172/AD5173
Rev. A | Page 2 of 24
TABLE OF CONTENTS
Electrical Characteristics—2.5 kΩ ................................................. 3
Electrical Characteristics—10 kΩ, 50 kΩ, 100 kΩ Versions ....... 4
Timing Characteristics—2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Versions
............................................................................................................. 5
Absolute Maximum Ratings............................................................ 6
Typical Performance Characteristics ............................................. 7
Test Circuits..................................................................................... 11
Operation......................................................................................... 12
One-Time Programming (OTP) .............................................. 12
Programming the Variable Resistor and Voltage.................... 12
Programming the Potentiometer Divider............................... 13
ESD Protection ........................................................................... 14
Terminal Voltage Operating Range.......................................... 14
Power-Up Sequence ................................................................... 14
Power Supply Considerations................................................... 14
Layout Considerations............................................................... 15
Evaluation Software/Hardware..................................................... 16
Software Programming ............................................................. 16
I2C Interface .................................................................................... 18
I2C Compatible 2-Wire Serial Bus ........................................... 20
Pin Configuration and Function Descriptions........................... 22
Outline Dimensions....................................................................... 23
Ordering Guide............................................................................... 24
REVISION HISTORY
Revision A
11/03—Data Sheet Changed from Rev. 0 to Rev. A
Change Location
Changes to Electrical Characteristics—2.5 kΩ......................... 3
AD5172/AD5173
Rev. A | Page 3 of 24
ELECTRICAL CHARACTERISTICS—2.5 kΩ
Table 1. VDD = 5 V ± 10% or 3 V ± 10%; VA = +VDD; VB = 0 V; –40°C < TA < +125°C; unless otherwise noted
Parameter Symbol Conditions Min Typ1 Max Unit
DC CHARACTERISTICS—RHEOSTAT MODE
Resistor Differential Nonlinearity2 R-DNL RWB, VA = No Connect –2 ±0.1 +2 LSB
Resistor Integral Nonlinearity2 R-INL RWB, VA = No Connect –6 ±0.75 +6 LSB
Nominal Resistor Tolerance3 RAB T
A = 25°C –20 +55 %
Resistance Temperature Coefficient (RAB/RAB)/T VAB = VDD, Wiper = No Connect 35 ppm/°C
RWB (Wiper Resistance) RWB Code = 0x00, VDD = 5 V 160 200 Ω
DC CHARACTERISTICS—POTENTIOMETER DIVIDER MODE (Specifications Apply to all VRs)
Differential Nonlinearity4 DNL –1.5 ±0.1 +1.5 LSB
Integral Nonlinearity4 INL –2 ±0.6 +2 LSB
Voltage Divider Temperature
Coefficient
(∆VW/VW)/∆T Code = 0x80 15 ppm/°C
Full-Scale Error VWFSE Code = 0xFF –10 –2.5 0 LSB
Zero-Scale Error VWZSE Code = 0x00 0 2 10 LSB
RESISTOR TERMINALS
Voltage Range5 V
A, VB, VW GND VDD V
Capacitance6 A, B CA, CB f = 1 MHz, Measured to GND,
Code = 0x80
45 pF
Capacitance W CW f = 1 MHz, Measured to GND,
Code = 0x80
60 pF
Shutdown Supply Current7 I
A_SD V
DD = 5.5 V 0.01 1 µA
Common-Mode Leakage ICM V
A = VB = VDD/2 1 nA
DIGITAL INPUTS AND OUTPUTS
Input Logic High VIH V
DD = 5 V 2.4 V
Input Logic Low VIL V
DD = 5 V 0.8 V
Input Logic High VIH V
DD = 3 V 2.1 V
Input Logic Low VIL V
DD = 3 V 0.6 V
Input Current IIL V
IN = 0 V or 5 V ±1 µA
Input Capacitance6 C
IL 5 pF
POWER SUPPLIES
Power Supply Range VDD RANGE 2.7 5.5 V
OTP Supply Voltage VDD_OTP T
A = 25°C 6 6.5 V
Supply Current IDD V
IH = 5 V or VIL = 0 V 3.5 6 µA
OTP Supply Current IDD_OTP V
DD_OTP = 6 V, TA = 25°C 100 mA
Power Dissipation8 P
DISS V
IH = 5 V or VIL = 0 V, VDD = 5 V 30 µW
Power Supply Sensitivity PSS VDD = 5 V ± 10%, Code = Midscale ±0.02 ±0.08 %/%
DYNAMIC CHARACTERISTICS9
Bandwidth –3 dB BW_2.5K Code = 0x80 4.8 MHz
Total Harmonic Distortion THDW V
A = 1 V rms, VB = 0 V, f = 1 kHz 0.1 %
VW Settling Time tS V
A = 5 V, VB = 0 V, ±1 LSB Error Band 1 µs
Resistor Noise Voltage Density eN_WB R
WB = 1.25 kΩ, RS = 0 3.2 nV/√Hz
1 Typical specifications represent average readings at 25°C and VDD = 5 V.
2 Resistor position nonlinearity error, R-INL, is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic.
3 VAB = VDD, Wiper (VW) = no connect.
4 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. VA = VDD and VB = 0 V. DNL
specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions.
5 Resistor terminals A, B, W have no limitations on polarity with respect to each other.
6 Guaranteed by design and not subject to production test.
7 Measured at the A terminal. The A terminal is open circuited in shutdown mode.
8 PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation.
9 All dynamic characteristics use VDD = 5 V.
AD5172/AD5173
Rev. A | Page 4 of 24
ELECTRICAL CHARACTERISTICS—10 kΩ, 50 kΩ, 100 kΩ VERSIONS
Table 2. VDD = 5 V ± 10% or 3 V ± 10%; VA = VDD; VB = 0 V; –40°C < TA < +125°C; unless otherwise noted
Parameter Symbol Conditions Min Typ1 Max Unit
DC CHARACTERISTICS—RHEOSTAT MODE
Resistor Differential Nonlinearity2 R-DNL RWB, VA = No Connect –1 ±0.1 +1 LSB
Resistor Integral Nonlinearity2 R-INL RWB, VA = No Connect –2.5 ±0.25 +2.5 LSB
Nominal Resistor Tolerance3 ∆RAB T
A = 25°C –20 +20 %
Resistance Temperature Coefficient (∆RAB/RAB)/∆T VAB = VDD, Wiper = No Connect 35 ppm/°C
RWB (Wiper Resistance) RWB Code = 0x00, VDD = 5 V 160 200 Ω
DC CHARACTERISTICS—POTENTIOMETER DIVIDER MODE (Specifications Apply to all VRs)
Differential Nonlinearity4 DNL –1 ±0.1 +1 LSB
Integral Nonlinearity4 INL –1 ±0.3 +1 LSB
Voltage Divider Temperature Coefficient (∆VW/VW)/∆T Code = 0x80 15 ppm/°C
Full-Scale Error VWFSE Code = 0xFF –2.5 –1 0 LSB
Zero-Scale Error VWZSE Code = 0x00 0 1 2.5 LSB
RESISTOR TERMINALS
Voltage Range5 V
A, VB, VW GND VDD V
Capacitance6 A, B CA, CB f = 1 MHz, Measured to GND, Code = 0x80 45 pF
Capacitance6 W CW f = 1 MHz, Measured to GND, Code = 0x80 60 pF
Shutdown Supply Current7 I
A_SD V
DD = 5.5 V 0.01 1 µA
Common-Mode Leakage ICM V
A = VB = VDD/2 1 nA
DIGITAL INPUTS AND OUTPUTS
Input Logic High VIH V
DD = 5 V 2.4 V
Input Logic Low VIL V
DD = 5 V 0.8 V
Input Logic High VIH V
DD = 3 V 2.1 V
Input Logic Low VIL V
DD = 3 V 0.6 V
Input Current IIL V
IN = 0 V or 5 V ±1 µA
Input Capacitance6 C
IL 5 pF
POWER SUPPLIES
Power Supply Range VDD RANGE 2.7 5.5 V
OTP Supply Voltage8 V
DD_OTP 6 6.5 V
Supply Current IDD V
IH = 5 V or VIL = 0 V 3.5 6 µA
OTP Supply Current9 I
DD_OTP 100 mA
Power Dissipation10 P
DISS V
IH = 5 V or VIL = 0 V, VDD = 5 V 30 µW
Power Supply Sensitivity PSS VDD = +5 V ± 10%, Code = Midscale ±0.02 ±0.08 %/%
DYNAMIC CHARACTERISTICS11
Bandwidth –3 dB BW RAB = 10 kΩ, Code = 0x80 600 kHz
R
AB = 50 kΩ, Code = 0x80 100 kHz
R
AB = 100 kΩ, Code = 0x80 40 kHz
Total Harmonic Distortion THDW V
A =1 V rms, VB = 0 V, f = 1 kHz, RAB = 10 kΩ 0.1 %
VW Settling Time (10 kΩ/50 kΩ/100 kΩ) tS V
A = 5 V, VB = 0 V, ±1 LSB Error Band 2 µs
Resistor Noise Voltage Density eN_WB R
WB = 5 kΩ, RS = 0 9 nV/√Hz
1 Typical specifications represent average readings at 25°C and VDD = 5 V.
2 Resistor position nonlinearity error, R-INL, is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic.
3 VAB = VDD, Wiper (VW) = no connect.
4 INL and DNL are measured at VW with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. VA = VDD and VB = 0 V.
DNL specification limits of ±1 LSB maximum are guaranteed monotonic operating conditions.
5 Resistor terminals A, B, W have no limitations on polarity with respect to each other.
6 Guaranteed by design and not subject to production test.
7 Measured at the A terminal. The A terminal is open circuited in shutdown mode.
8 Different from operating power supply, power supply OTP is used one time only.
9 Different from operating current, supply current for OTP lasts approximately 400 ms for one time only.
10 PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation.
11 All dynamic characteristics use VDD = 5 V.
AD5172/AD5173
Rev. A | Page 5 of 24
TIMING CHARACTERISTICS—2.5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ VERSIONS
Table 3. VDD = 5 V ± 10% or 3V ± 10%; VA = VDD; VB = 0 V; –40°C < TA < +125°C; unless otherwise noted
Parameter Symbol Conditions Min Typ Max Unit
I2C INTERFACE TIMING CHARACTERISTICS1 (Specifications Apply to All Parts)
SCL Clock Frequency fSCL 400 kHz
tBUF Bus Free Time between STOP and START t1 1.3 µs
tHD;STA Hold Time (Repeated START) t2 After this period, the first clock pulse is
generated.
0.6 µs
tLOW Low Period of SCL Clock t3 1.3 µs
tHIGH High Period of SCL Clock t4 0.6 µs
tSU;STA Setup Time for Repeated START Condition t5 0.6 µs
tHD;DAT Data Hold Time2 t
6 0.9 µs
tSU;DAT Data Setup Time t7 100 ns
tF Fall Time of Both SDA and SCL Signals t8 300 ns
tR Rise Time of Both SDA and SCL Signals t9 300 ns
tSU;STO Setup Time for STOP Condition t10 0.6 µs
1 See timing diagrams for locations of measured values.
2 The maximum tHD;DAT has only to be met if the device does not stretch the LOW period (tLOW) of the SCL signal.
AD5172/AD5173
Rev. A | Page 6 of 24
ABSOLUTE MAXIMUM RATINGS
Table 4. TA = 25°C, unless otherwise noted
Parameter Value
VDD to GND –0.3 V to +7 V
VA, VB, VW to GND VDD
Terminal Current, Ax–Bx, Ax–Wx, Bx–Wx1
Pulsed ±20 mA
Continuous ±5 mA
Digital Inputs and Output Voltage to GND 0 V to 7 V
Operating Temperature Range –40°C to +125°C
Maximum Junction Temperature (TJMAX) 150°C
Storage Temperature –65°C to +150°C
Lead Temperature (Soldering, 10 sec) 300°C
Thermal Resistance2 θJA: MSOP-10 230°C/W
1 Maximum terminal current is bound by the maximum current handling of
the switches, maximum power dissipation of the package, and maximum
applied voltage across any two of the A, B, and W terminals at a given
resistance.
2 Package power dissipation = (TJMAX – TA)/θJA.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
AD5172/AD5173
Rev. A | Page 7 of 24
TYPICAL PERFORMANCE CHARACTERISTICS
–2.0
–1.5
–1.0
–0.5
0
0.5
RHEOSTAT MODE INL (LSB)
1.0
1.5
2.0
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-003
V
DD
= 5.5V
T
A
= 25°C
R
AB
= 10kΩ
V
DD
= 2.7V
Figure 3. R-INL vs. Code vs. Supply Voltages
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
0.5
RHEOSTAT MODE DNL (LSB)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-004
TA = 25°C
RAB = 10kΩ
VDD = 2.7V
VDD = 5.5V
Figure 4. R-DNL vs. Code vs. Supply Voltages
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
0.5
POTENTIOMETER MODE INL (LSB)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-005
RAB = 10kΩ
VDD = 2.7V
TA = –40°C, +25°C, +85°C, +125°C
VDD = 5.5V
TA = –40°C, +25°C, +85°C, +125°C
Figure 5. INL vs. Code vs. Temperature
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
0.5
POTENTIOMETER MODE DNL (LSB)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-006
VDD = 2.7V; TA = –40°C, +25°C, +85°C, +125°C
RAB = 10kΩ
Figure 6. DNL vs. Code vs. Temperature
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
POTENTIOMETER MODE INL (LSB)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-007
TA = 25°C
RAB = 10kΩ
VDD = 2.7V
VDD = 5.5V
Figure 7. INL vs. Code vs. Supply Voltages
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
0.5
POTENTIOMETER MODE DNL (LSB)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-008
T
A
= 25°C
R
AB
= 10kΩ
V
DD
= 2.7V
V
DD
= 5.5V
Figure 8. DNL vs. Code vs. Supply Voltages
AD5172/AD5173
Rev. A | Page 8 of 24
–2.0
–1.5
–1.0
–0.5
0
0.5
RHEOSTAT MODE INL (LSB)
1.0
1.5
2.0
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-009
R
AB
= 10kΩ
V
DD
= 2.7V
T
A
= –40°C, +25°C, +85°C, +125°C
V
DD
= 5.5V
T
A
= –40°C, +25°C, +85°C, +125°C
Figure 9. R-INL vs. Code vs. Temperature
–0.5
–0.4
–0.3
–0.2
–0.1
0
0.1
0.2
0.3
0.4
0.5
RHEOSTAT MODE DNL (LSB)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-010
V
DD
= 2.7V, 5.5V; T
A
= –40°C, +25°C, +85°C, +125°C
R
AB
= 10kΩ
Figure 10. R-DNL vs. Code vs. Temperature
–2.0
–1.5
–1.0
–0.5
0
0.5
FSE, FULL-SCALE ERROR (LSB)
1.0
1.5
2.0
TEMPERATURE (°C)
–40 –25 –10 5 20 35 50 65 80 95 110 125
04103-0-011
V
DD
= 5.5V, V
A
= 5.0V
R
AB
= 10kΩ
V
DD
= 2.7V, V
A
= 2.7V
Figure 11. Full-Scale Error vs. Temperature
0
0.75
1.50
2.25
3.00
3.75
4.50
ZSE, ZERO-SCALE ERROR (LSB)
TEMPERATURE (°C)
–40 –25 –10 5 20 35 50 65 80 95 110 125
04103-0-012
V
DD
= 5.5V, V
A
= 5.0V
R
AB
= 10kΩ
V
DD
= 2.7V, V
A
= 2.7V
Figure 12. Zero-Scale Error vs. Temperature
I
DD
, SUPPLY CURRENT (µA)
0.1
1
10
–40 –7 26 59 92 125
TEMPERATURE (°C)
04103-0-013
V
DD
= 5V
V
DD
= 3V
Figure 13. Supply Current vs. Temperature
–20
0
20
40
60
80
100
120
RHEOSTAT MODE TEMPCO (ppm/°C)
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-014
R
AB
= 10kΩ
V
DD
= 2.7V
T
A
= –40°C TO +85°C, –40°C TO +125°C
V
DD
= 5.5V
T
A
= –40°C TO +85°C, –40°C TO +125°C
Figure 14. Rheostat Mode Tempco ∆RWB/∆T vs. Code
AD5172/AD5173
Rev. A | Page 9 of 24
–30
–20
–10
0
10
20
POTENTIOMETER MODE TEMPCO (ppm/°C)
30
40
50
1289632 640 160 192 224 256
CODE (DECIMAL)
04103-0-047
R
AB
= 10kΩ
V
DD
= 2.7V
T
A
= –40°C TO +85°C, –40°C TO +125°C
V
DD
= 5.5V
T
A
= –40°C TO +85°C, –40°C TO +125°C
Figure 15. AD5172 Potentiometer Mode Tempco ∆VWB/∆T vs. Code
–60
–54
–48
–42
–36
–30
–24
–18
–12
–6
0
GAIN (dB)
FREQUENCY (Hz)
10k 1M100k 10M
04103-0-048
0x80
0x40
0x20
0x10
0x08
0x04
0x010x02
Figure 16. Gain vs. Frequency vs. Code, RAB = 2.5 kΩ
–60
–54
–48
–42
–36
–30
–24
–18
–12
–6
0
GAIN (dB)
FREQUENCY (Hz)
1k 100k10k 1M
04103-0-049
0x80
0x40
0x20
0x10
0x08
0x04
0x01
0x02
Figure 17. Gain vs. Frequency vs. Code, RAB = 10 kΩ
–60
–54
–48
–42
–36
–30
–24
–18
–12
–6
0
GAIN (dB)
FREQUENCY (Hz)
1k 100k10k 1M
04103-0-050
0x80
0x40
0x20
0x10
0x08
0x04
0x01
0x02
Figure 18. Gain vs. Frequency vs. Code, RAB = 50 kΩ
–60
–54
–48
–42
–36
–30
–24
–18
–12
–6
0
GAIN (dB)
FREQUENCY (Hz)
1k 100k10k 1M
04103-0-051
0x80
0x40
0x20
0x10
0x08
0x04
0x01
0x02
Figure 19. Gain vs. Frequency vs. Code, RAB = 100 kΩ
–60
–54
–48
–42
–36
–30
–24
–18
–12
–6
0
GAIN (dB)
FREQUENCY (Hz)
10k1k 100k 1M 10M
04103-0-052
100kΩ
60kHz 50kΩ
120kHz 10kΩ
570kHz
2.5kΩ
2.2MHz
Figure 20. –3 dB Bandwidth @ Code = 0x80
AD5172/AD5173
Rev. A | Page 10 of 24
I
DD
, SUPPLY CURRENT (mA)
0.01
1
0.1
10
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
DIGITAL INPUT VOLTAGE (V)
04103-0-057
T
A
= 25°C
V
DD
= 2.7V
V
DD
= 5.5V
Figure 21. IDD vs. Input Voltage
04103-0-053
SCL
V
W
Figure 22. Digital Feedthrough
04103-0-054
V
W1
V
W2
Figure 23. Digital Crosstalk
04103-0-056
V
W1
V
W2
Figure 24. Analog Crosstalk
04103-0-058
V
W
Figure 25. Midscale Glitch, Code 0x80 to 0x7F
04103-0-055
SCL
V
W
Figure 26. Large Signal Settling Time
AD5172/AD5173
Rev. A | Page 11 of 24
TEST CIRCUITS
Figure 27 to Figure 34 illustrate the test circuits that define the
test conditions used in the product specification tables.
04103-0-015
V
MS
AW
B
DUT
V+
V+ = V
DD
1LSB = V+/2
N
Figure 27. Test Circuit for Potentiometer Divider Nonlinearity Error (INL, DNL)
04103-0-016
NO CONNECT
I
W
V
MS
AW
B
DUT
Figure 28. Test Circuit for Resistor Position Nonlinearity Error
(Rheostat Operation; R-INL, R-DNL)
04103-0-017
V
MS1
I
W
= V
DD
/R
NOMINAL
V
MS2
V
W
R
W
= [V
MS1
– V
MS2
]/I
W
AW
B
DUT
Figure 29. Test Circuit for Wiper Resistance
04103-0-018
∆V
MS
%
DD
%
PSS (%/%) =
V+ = V
DD
10%
PSRR (dB) = 20 LOG
DUT
MS
DD
( )
V
DD
V
A
V
MS
AW
B
V+ ∆V
∆V
∆V
Figure 30. Test Circuit for Power Supply Sensitivity (PSS, PSSR)
04103-0-019
+15V
–15V
W
A
2.5V B
V
OUT
OFFSET
GND
DUT
AD8610
V
IN
Figure 31. Test Circuit for Gain vs. Frequency
04103-0-020
W
B
DUT
I
SW
CODE = 0x00
R
SW
=0.1V
I
SW
0.1V
GND TO V
DD
Figure 32. Test Circuit for Incremental On Resistance
04103-0-021
V
DD
AW
B
DUT
GND
I
CM
V
CM
NC
NC
Figure 33. Test Circuit for Common-Mode Leakage Current
04103-0-022
V
IN
N/C W1
B1 B2
W2
RDAC1
A1
RDAC2
V
DD
V
SS
V
OUT
CTA = 20 log[V
OUT
/V
IN
]
A2
Figure 34. Test Circuit for Analog Crosstalk
AD5172/AD5173
Rev. A | Page 12 of 24
OPERATION
SDA
SCL A
W
B
FUSES
EN
DAC
REG.
I
2
C INTERFACE
COMPARATOR
ONE-TIME
PROGRAM/TEST
CONTROL BLOCK
MUX DECODER
FUSE
REG.
04103-0-026
Figure 35. Detailed Functional Block Diagram
The AD5172/AD5173 is a 256-position, digitally controlled
variable resistor (VR) that employs fuse link technology to
achieve memory retention of resistance setting.
An internal power-on preset places the wiper at midscale
during power-on. If the OTP function has been activated, the
device powers up at the user-defined permanent setting.
ONE-TIME PROGRAMMING (OTP)
Prior to OTP activation, the AD5172/AD5173 presets to mid-
scale during initial power-on. After the wiper is set at the
desired position, the resistance can be permanently set by
programming the T bit high along with the proper coding (see
Table 5 and Table 6). Note that fuse link technology requires 6 V
to blow the internal fuses to achieve a given setting. The user is
allowed only one attempt at blowing the fuses. Once program-
ming is completed, the power supply voltage must be reduced to
the normal operating range of 2.7 V to 5.5 V.
The device control circuit has two validation bits, E1 and E0,
that can be read back to check the programming status (see
Table 7). Users should always read back the validation bits to
ensure that the fuses are properly blown. After the fuses have
been blown, all fuse latches are enabled upon subsequent
power-on; therefore, the output corresponds to the stored
setting. Figure 35 shows a detailed functional block diagram.
PROGRAMMING THE VARIABLE RESISTOR AND
VOLTAGE
Rheostat Operation
The nominal resistance of the RDAC between terminals A and
B is available in 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ. The nominal
resistance (RAB) of the VR has 256 contact points accessed by
the wiper terminal, plus the B terminal contact. The 8-bit data
in the RDAC latch is decoded to select one of the 256 possible
settings.
A
W
B
A
W
B
A
W
B
04103-0-027
Figure 36. Rheostat Mode Configuration
Assuming a 10 kΩ part is used, the wiper’s first connection
starts at the B terminal for data 0x00. Because there is a 50 Ω
wiper contact resistance, such a connection yields a minimum
of 100 Ω (2 × 50 Ω) resistance between terminals W and B. The
second connection is the first tap point, which corresponds to
139 Ω (RWB = RAB/256 + 2 × RW = 39 Ω + 2 × 50 Ω) for data
0x01. The third connection is the next tap point, representing
178 Ω (2 × 39 Ω + 2 × 50 Ω) for data 0x02, and so on. Each LSB
data value increase moves the wiper up the resistor ladder until
the last tap point is reached at 10,100 Ω (RAB + 2 × RW).
D5
D4
D3
D7
D6
D2
D1
D0
RDAC
LATCH
AND
DECODER
R
S
R
S
R
S
R
S
A
W
B
04103-0-028
Figure 37. AD5172/AD5173 Equivalent RDAC Circuit
AD5172/AD5173
Rev. A | Page 13 of 24
The general equation that determines the digitally programmed
output resistance between W and B is
WABWB RR
D
DR ×+×= 2
128
)( (1)
where D is the decimal equivalent of the binary code loaded in
the 8-bit RDAC register, RAB is the end-to-end resistance, and
RW is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if RAB = 10 kΩ and the A terminal is open-
circuited, the output resistance RWB is set for the RDAC latch
codes, as shown in Table 5.
Table 5. Codes and Corresponding RWB Resistance
D (Dec.) RWB (Ω) Output State
255 9,961 Full-Scale (RAB – 1 LSB + RW)
128 5,060 Midscale
1 139 1 LSB
0 100 Zero-Scale (Wiper Contact Resistance)
Note that in the zero-scale condition, a finite wiper resistance of
100 Ω is present. Care should be taken to limit the current flow
between W and B in this state to a maximum pulse current of
no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switch contact can occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between the wiper W and terminal A also produces a
digitally controlled complementary resistance, RWA . When these
terminals are used, the B terminal can be opened. Setting the
resistance value for RWA starts at a maximum value of resistance
and decreases as the data loaded in the latch increases in value.
The general equation for this operation is
WABWA RR
D
DR ×+×= 2
128
–256
)( (2)
For RAB = 10 kΩ and the B terminal open-circuited, the
following output resistance RWA is set for the RDAC latch codes,
as shown in Table 6.
Table 6. Codes and Corresponding RWA Resistance
D (Dec.) RWA (Ω) Output State
255 139 Full-Scale
128 5,060 Midscale
1 9,961 1 LSB
0 10,060 Zero-Scale
Typical device-to-device matching is process lot dependent and
may vary by up to ±30%. Because the resistance element is pro-
cessed using thin film technology, the change in RAB with
temperature has a very low 35 ppm/°C temperature coefficient.
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
The digital potentiometer easily generates a voltage divider at
wiper-to-B and wiper-to-A proportional to the input voltage at
A-to-B. Unlike the polarity of VDD to GND, which must be posi-
tive, voltage across A-B, W-A, and W-B can be at either polarity.
A
V
I
W
B
V
O
04103-0-029
Figure 38. Potentiometer Mode Configuration
If ignoring the effect of the wiper resistance for approximation,
connecting the A terminal to 5 V and the B terminal to ground
produces an output voltage at the wiper-to-B starting at 0 V up
to 1 LSB less than 5 V. Each LSB of voltage is equal to the
voltage applied across terminal AB divided by the 256 positions
of the potentiometer divider. The general equation defining the
output voltage at VW with respect to ground for any valid input
voltage applied to terminals A and B is
B
A
WV
D
V
D
DV
256
256
256
)( −
+= (3)
For a more accurate calculation, which includes the effect of
wiper resistance, VW can be found as
B
AB
WA
A
AB
WB
WV
R
DR
V
R
DR
DV )(
)(
)( += (4)
Operation of the digital potentiometer in the divider mode
results in a more accurate operation over temperature. Unlike
the rheostat mode, the output voltage is dependent mainly on
the ratio of the internal resistors RWA and RWB and not the abso-
lute values. Thus, the temperature drift reduces to 15 ppm/°C.
AD5172/AD5173
Rev. A | Page 14 of 24
ESD PROTECTION
All digital inputs—SDA, SCL, AD0, and AD1— are protected
with a series input resistor and parallel Zener ESD structures, as
shown in Figure 39 and Figure 40.
LOGIC
340Ω
GND
04103-0-030
Figure 39. ESD Protection of Digital Pins
A,B,W
GND
04103-0-031
Figure 40. ESD Protection of Resistor Terminals
TERMINAL VOLTAGE OPERATING RANGE
The AD5172/AD5173 V
DD
to GND power supply defines the
boundary conditions for proper 3-terminal digital potentiom-
eter operation. Supply signals present on terminals A, B, and W
that exceed V
DD
or GND are clamped by the internal forward-
biased diodes (see Figure 41).
GND
A
W
B
V
DD
04103-0-032
Figure 41. Maximum Terminal Voltages Set by V
DD
and GND
POWER-UP SEQUENCE
Because the ESD protection diodes limit the voltage compliance
at terminals A, B, and W (see Figure 41), it is important to
power VDD/GND before applying any voltage to terminals A, B,
and W. Otherwise, the diode will be forward biased such that
VDD is powered unintentionally and may affect the rest of the
user’s circuit. The ideal power-up sequence is GND, VDD, the
digital inputs, and then VA/VB/VW. The relative order of
powering VA, VB, VW, and the digital inputs is not important as
long as they are powered after VDD/GND.
POWER SUPPLY CONSIDERATIONS
To minimize the package pin count, both the one-time pro-
gramming and normal operating voltage supplies are applied to
the same VDD terminal of the AD5172/AD5173. The AD5172/
AD5173 employ fuse link technology that requires 6 V to blow
the internal fuses to achieve a given setting. The user is allowed
only one attempt at blowing the fuses. Once programming is
completed, power supply voltage must be reduced to the normal
2.7 V to 5.5 V operating range. Such dual voltage requirements
require isolation between the supplies. The fuse programming
supply (either an on-board regulator or rack-mount power sup-
ply) must be rated at 6 V and must be able to provide a 100 mA
transient current for 400 ms for successful one-time program-
ming. Once programming is complete, the 6 V supply must be
removed to allow normal operation at 2.7 V to 5.5 V at regular
microamp current levels. Figure 42 shows the simplest imple-
mentation using a jumper. This approach saves one voltage
supply, but draws additional current and requires manual
configuration.
V
DD
6V
R1 50kΩ
R2
C1
1µFC2
1nF
250kΩ
5V
CONNECT J1 HERE
FOR OTP
CONNECT J1 HERE
AFTER OTP
AD5172/
AD5173
04103-0-033
Figure 42. Power Supply Requirement
An alternate approach in 3.5 V to 5.5 V systems adds a signal
diode between the system supply and the OTP supply for
isolation, as shown in Figure 43.
VDD
3.5V–5.5V
6V
D1
C1
1µFC2
1nF
APPLY FOR OTP ONLY
AD5172/
AD5173
04103-0-034
Figure 43. Isolate 6 V OTP Supply from 3.5 V to 5.5 V Normal Operating
Supply. The 6 V supply must be removed once OTP is completed.
AD5172/AD5173
Rev. A | Page 15 of 24
V
DD
2.7V
6V
P1
P1=P2=FDV302P, NDS0610
R1
10kΩ
P2 C1
1µFC2
1nF
APPLY FOR OTP ONLY
AD5172/
AD5173
04103-0-035
Poor PCB layout introduces parasitics that may affect the fuse
programming. Therefore, it is recommended to add a 1 µF
tantalum capacitor in parallel with a 1 nF ceramic capacitor as
close as possible to the VDD pin. These capacitors help ensure
OTP programming success by providing proper current densi-
ties. This combination of capacitor values provides both a fast
response for high frequency transients and a larger supply of
current for extended spikes. Typically, C1 minimizes any
transient disturbances and low frequency ripple, while C2
reduces high frequency noise.
Figure 44. Isolate 6 V OTP Supply from 2.7 V Normal Operating Supply.
The 6 V supply must be removed once OTP is completed. LAYOUT CONSIDERATIONS
It is a good practice to employ compact, minimum lead length
layout design. The leads to the inputs should be as direct as
possible with a minimum conductor length. Ground paths
should have low resistance and low inductance.
For users who operate their systems at 2.7 V, use of the
bidirectional low threshold P-Ch MOSFETs is recommended
for the supply’s isolation. As shown in Figure 44, this assumes
that the 2.7 V system voltage is applied first, and that the P1 and
P2 gates are pulled to ground, thus turning on P1 and
subsequently P2. As a result, VDD of the AD5172/AD5173
approaches 2.7 V. When the AD5172/AD5173 setting is found,
the factory tester applies the 6 V to VDD; the 6 V is also applied
to the gates of P1 and P2 to turn them off. The OTP command
is executed at this time to program the AD5172/AD5173; the
2.7 V source is therefore protected. Once the OTP is completed,
the tester withdraws the 6 V and the AD5172/AD5173’s setting
is fixed permanently.
Note that the digital ground should also be joined remotely to
the analog ground at one point to minimize the ground bounce.
V
DD
GND
V
DD
C1
1µFC2
1nF
AD5172
+
04103-0-036
AD5172/AD5173 achieves the OTP function through blowing
internal fuses. Users should always apply the 6 V one-time
program voltage requirement at the first program command.
Failure to comply with this requirement may lead to the change
of fuse structures, rendering programming inoperable.
Figure 45. Power Supply Bypassing
AD5172/AD5173
Rev. A | Page 16 of 24
EVALUATION SOFTWARE/HARDWARE
Figure 46. AD5172/AD5173 Computer Software Interface
There are two ways of controlling the AD5172/AD5173. Users
can either program the devices with computer software or with
external I2C controllers.
SOFTWARE PROGRAMMING
Due to the advantages of the one-time programmable feature,
users may consider programming the device in the factory
before shipping the final product to end-users. ADI offers a
device programming software that can be implemented in the
factory on PCs running Windows 95 or later. As a result,
external controllers are not required, which significantly
reduces development time. The program is an executable file
that does not require any programming languages or user
programming skills. It is easy to set up and to use. Figure 46
shows the software interface. The software can be downloaded
from www.analog.com.
The AD5172/AD5173 starts at midscale after power-up prior to
OTP programming. To increment or decrement the resistance,
the user may simply move the scrollbars on the left. To write
any specific value, the user should use the bit pattern in the
upper screen and press the Run button. The format of writing
data to the device is shown in Table 7. Once the desired setting
is found, the user may press the Program Permament button to
blow the internal fuse links.
To read the validation bits and data out from the device, the
user simply presses the Read button. The format of the read bits
is shown in Table 8.
To apply the device programming software in the factory, users
must modify a parallel port cable and configure Pins 2, 3, 15,
and 25 for SDA_write, SCL, SDA_read, and DGND, respectively,
for the control signals (Figure 47). Users should also lay out the
PCB of the AD5172/AD5173 with SCL and SDA pads, as shown
in Figure 48, such that pogo pins can be inserted for factory
programming.
AD5172/AD5173
Rev. A | Page 17 of 24
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
SCL
R3
100Ω
R2
100Ω
R1
100Ω
SDA
READ
WRITE
04103-0-037
AD5172 AD5173
W1
B2
A2
SDA
SCL
B1
AD0
W2
GND
VDD
B1
A1
W2
GND
VDD
W1
B2
AD1
SDA
SCL
04103-0-038
Figure 48. Recommended AD5172/AD5173 PCB Layout. The SCL and SDA
pads allow pogo pins to be inserted so that signals can be communicated
through the parallel port for programming (Figure 47).
Figure 47. Parallel Port Connection. Pin 2 = SDA_write, Pin 3 = SCL,
Pin 15 = SDA_read, and Pin 25 = DGND.
AD5172/AD5173
Rev. A | Page 18 of 24
I2C INTERFACE
Table 7. Write Mode
AD5172
S 0 1 0 1 1 1 1 W A A0 SD T 0 OW X X X A D7 D6 D5 D4 D3 D2 D1 D0 A P
Slave Address Byte Instruction Byte Data Byte
AD5173
S 0 1 0 1 1 AD1 AD0
W A A0 SD T 0 OW X X X A D7 D6 D5 D4 D3 D2 D1 D0 A P
Slave Address Byte Instruction Byte Data Byte
Table 8. Read Mode
AD5172
S 0 1 0 1 1 1 1 R A D7 D6 D5 D4 D3 D2 D1 D0 A E1 E0 X X X X X X A P
Slave Address Byte Instruction Byte Data Byte
AD5173
S 0 1 0 1 1 AD1 AD0 R A D7 D6 D5 D4 D3 D2 D1 D0 A E1 E0 X X X X X X A P
Slave Address Byte Instruction Byte Data Byte
S = Start Condition
P = Stop Condition
A = Acknowledge
AD0, AD1 = Package Pin Programmable Address Bits
X = Don’t Care
W = Write
R = Read
A0 = RDAC Subaddress Select Bit
SD = Shutdown connects wiper to B terminal and open circuits
the A terminal. It does not change contents of wiper register.
T = OTP Programming Bit. Logic 1 programs the wiper
permanently.
OW = Overwrite the fuse setting and program the digital
potentiometer to a different setting. Note that upon power-up,
the digital potentiometer is preset to either midscale or fuse
setting, depending on whether not the fuse link has been blown.
D7, D6, D5, D4, D3, D2, D1, D0 = Data Bits.
E1, E0 = OTP Validation Bits.
0, 0 = Ready to Program.
1, 0 = Fatal Error. Some fuses not blown. Do not retry. Discard
this unit.
1, 1 = Programmed Successfully. No further adjustments
possible.
AD5172/AD5173
Rev. A | Page 19 of 24
04103-0-039
t1
t2t3
t8
t8
t9
t9
t6
t4t7t5
t2
t10
PS S
SCL
SDA
P
Figure 49. I2C Interface Detailed Timing Diagram
04103-0-040
SCL
START BY
MASTER
SDA 01
1
FRAME 1
SLAVE ADDRESS BYTE
01111
FRAME 2
INSTRUCTION BYTE
ACK BY
AD5172
R/W A0 SD 0 OW X X X
19
D7 D6 D5 D4 D3
ACK BY
AD5172 FRAME 3
DATA BYTE
19
T
STOP BY
MASTER
9
D2 D1 D0
ACK BY
AD5172
Figure 50. Writing to the RDAC Register—AD5172
04103-0-041
SCL
START BY
MASTER
SDA 01
1
FRAME 1
SLAVE ADDRESS BYTE
0 1 1 AD1 AD0
FRAME 2
INSTRUCTION BYTE
ACK BY
AD5173
R/W A0 SD 0 OW X X X
19
D7 D6 D5 D4 D3
ACK BY
AD5173 FRAME 3
DATA BYTE
19
T
STOP BY
MASTER
9
D2 D1 D0
ACK BY
AD5173
Figure 51. Writing to the RDAC Register—AD5173
04103-0-042
SCL
START BY
MASTER
SDA 01
1
FRAME 1
SLAVE ADDRESS BYTE
01111
FRAME 2
INSTRUCTION BYTE
ACK BY
AD5172
R/W D7 D6 D4 D3 D2 D1 D0
19
E1 E0 X X X
ACK BY
MASTER FRAME 3
DATA BYTE
19
D5
STOP BY
MASTER
9
XXX
NO ACK
BY MASTER
Figure 52. Reading Data from a Previously Selected RDAC Register in Write Mode—AD5172
04103-0-043
SCL
START BY
MASTER
SDA 01
1
FRAME 1
SLAVE ADDRESS BYTE
0 1 1 AD1 AD0
FRAME 2
INSTRUCTION BYTE
ACK BY
AD5173
R/W D7 D6 D4 D3 D2 D1 D0
19
E1 E0 X X X
ACK BY
MASTER FRAME 3
DATA BYTE
19
D5
STOP BY
MASTER
9
XXX
NO ACK
BY MASTER
Figure 53. Reading Data from a Previously Selected RDAC Register in Write Mode—AD5173
AD5172/AD5173
Rev. A | Page 20 of 24
I2C COMPATIBLE 2-WIRE SERIAL BUS
The 2-wire I2C serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a START
condition, which is when a high-to-low transition on the
SDA line occurs while SCL is high (see Figure 50 and
Figure 51). The following byte is the slave address byte,
which consists of the slave address followed by an R/W bit
(this bit determines whether data is read from or written to
the slave device). The AD5172 has a fixed slave address
byte, whereas the AD5173 has two configurable address
bits, AD0 and AD1 (see Figure 50 and Figure 51).
The slave whose address corresponds to the transmitted
address responds by pulling the SDA line low during the
ninth clock pulse (this is termed the acknowledge bit). At
this stage, all other devices on the bus remain idle while the
selected device waits for data to be written to or read from
its serial register. If the R/W bit is high, the master reads
from the slave device. If the R/W bit is low, the master
writes to the slave device.
2. In the write mode, the second byte is the instruction byte.
The first bit (MSB) of the instruction byte is the RDAC
subaddress select bit. A logic low selects channel 1; a logic
high selects channel 2.
The second MSB, SD, is a shutdown bit. A logic high causes
an open circuit at terminal A while shorting the wiper to
terminal B. This operation yields almost 0 Ω in rheostat
mode or 0 V in potentiometer mode. It is important to note
that the shutdown operation does not disturb the contents
of the register. When brought out of shutdown, the previ-
ous setting is applied to the RDAC. Also, during shutdown,
new settings can be programmed. When the part is
returned from shutdown, the corresponding VR setting is
applied to the RDAC.
The third MSB, T, is the OTP programming bit. A logic
high blows the poly fuses and programs the resistor setting
permanently.
The fourth MSB must always be at Logic 0.
The fifth MSB, OW, is an overwrite bit. When raised to a
logic high, OW allows the RDAC setting to be changed
even after the internal fuses have been blown. However,
once OW is returned to a logic zero, the position of the
RDAC returns to the setting prior to overwrite. Because
OW is not static, if the device is powered off and on, the
RDAC presets to midscale or to the setting at which the
fuses were blown, depending on whether or not the fuses
have been permanently set already.
The remainder of the bits in the instruction byte are don’t
cares (see Figure 50 and Figure 51).
After acknowledging the instruction byte, the last byte in
write mode is the data byte. Data is transmitted over the
serial bus in sequences of nine clock pulses (eight data bits
followed by an acknowledge bit). The transitions on the
SDA line must occur during the low period of SCL and
remain stable during the high period of SCL (see
Figure 49).
3. In the read mode, the data byte follows immediately after
the acknowledgment of the slave address byte. Data is
transmitted over the serial bus in sequences of nine clock
pulses (a slight difference from the write mode, where there
are eight data bits followed by an acknowledge bit). Simi-
larly, the transitions on the SDA line must occur during the
low period of SCL and remain stable during the high
period of SCL (see Figure 52 and Figure 53).
Note that the channel of interest is the one that is
previously selected in the write mode. In the case where
users need to read the RDAC values of both channels, they
must program the first channel in the write mode and then
change to the read mode to read the first channel value.
After that, the user must change back to the write mode
with the second channel selected and read the second
channel value in the read mode. It is not necessary for users
to issue the Frame 3 data byte in the write mode for subse-
quent readback operation. Refer to Figure 52 and Figure 53
for the programming format.
Following the data byte, the validation byte contains two
validation bits, E0 and E1. These bits signify the status of
the one-time programming (see Figure 52 and Figure 53).
4. After all data bits have been read or written, a STOP
condition is established by the master. A STOP condition is
defined as a low-to-high transition on the SDA line while
SCL is high. In write mode, the master pulls the SDA line
high during the 10th clock pulse to establish a STOP
condition (see Figure 50 and Figure 51). In read mode, the
master issues a No Acknowledge for the ninth clock pulse
(i.e., the SDA line remains high). The master then brings
the SDA line low before the 10th clock pulse, which goes
high to establish a STOP condition (see Figure 52 and
Figure 53).
A repeated write function gives the user flexibility to update the
RDAC output a number of times after addressing and instruc-
ting the part only once. For example, after the RDAC has
acknowledged its slave address and instruction bytes in the
write mode, the RDAC output is updated on each successive
byte. If different instructions are needed, the write/read mode
has to start again with a new slave address, instruction, and data
byte. Similarly, a repeated read function of the RDAC is also
allowed.
AD5172/AD5173
Rev. A | Page 21 of 24
Table 9. Validation Status
E1 E0 Status
0 0 Ready for Programming.
1 0 Fatal Error. Some fuses not blown.
Do not retry. Discard this unit.
1 1 Successful. No further
programming is possible.
Multiple Devices on One Bus(AD5173 Only)
Figure 54 shows four AD5173s on the same serial bus. Each has
a different slave address because the states of their AD0 and
AD1 pins are different. This allows each device on the bus to be
written to or read from independently. The master device
output bus line drivers are open-drain pull-downs in a fully I2C
compatible interface.
SDA
SDA
AD1
AD0
MASTER
SCL
SCL
AD5173
SDA
AD1
AD0
SCL
AD5173
SDA
AD1
AD0
SCL
AD5173
SDA
5V
R
P
R
P
5V
5V
5V
AD1
AD0
SCL
AD5173
04103-0-044
Figure 54. Multiple AD5173s on One I2C Bus
AD5172/AD5173
Rev. A | Page 22 of 24
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
10
9
8
7
1
2
3
4
B1
A1
W2
W1
B2
A2
SDAGND
6
5
SCLV
DD
TOP VIEW
AD5172
04103-0-045
Figure 55. AD5172 Pin Configuration
10
9
8
7
1
2
3
4
B1
AD0
W2
W1
B2
AD1
SDAGND
6
5
SCLV
DD
TOP VIEW
AD5173
04103-0-046
Figure 56. AD5173 Pin Configuration
Table 10. AD5172 Pin Function Descriptions
Pin Menmonic Description
1 B1 B1 Terminal.
2 A1 A1 Terminal.
3 W2 W2 Terminal.
4 GND Digital Ground.
5 VDD Positive Power Supply.
6 SCL Serial Clock Input. Positive edge triggered.
7 SDA Serial Data Input/Output.
8 A2 A2 Terminal.
9 B2 B2 Terminal.
10 W1 W1 Terminal.
Table 11.AD5173 Pin Function Descriptions
Pin Mnemonic Description
1 B1 B1 Terminal.
2 AD0 Programmable Address Bit 0 for Multiple
Package Decoding.
3 W2 W2 Terminal.
4 GND Digital Ground.
5 VDD Positive Power Supply.
6 SCL Serial Clock Input. Positive edge triggered.
7 SDA Serial Data Input/Output.
8 AD1 Programmable Address Bit 1 for Multiple
Package Decoding.
9 B2 B2 Terminal.
10 W1 W1 Terminal.
AD5172/AD5173
Rev. A | Page 23 of 24
OUTLINE DIMENSIONS
0.23
0.08
0.80
0.60
0.40
8°
0°
0.15
0.00 0.27
0.17
0.95
0.85
0.75
SEATING
PLANE
1.10 MAX
10 6
5
1
0.50 BSC
3.00 BSC
3.00 BSC
4.90 BSC
PIN 1
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187BA
Figure 57. 10-Lead Mini Small Outline Package [MSOP]
(RM-10)
Dimensions shown in millimeters
AD5172/AD5173
Rev. A | Page 24 of 24
ORDERING GUIDE
Model RAB (kΩ) Temperature Range Package Description Package Option Branding
AD5172BRM2.5 2.5 –40°C to +125°C MSOP-10 RM-10 D0U
AD5172BRM2.5-RL7 2.5 –40°C to +125°C MSOP-10 RM-10 D0U
AD5172BRM10 10 –40°C to +125°C MSOP-10 RM-10 D0V
AD5172BRM10-RL7 10 –40°C to +125°C MSOP-10 RM-10 D0V
AD5172BRM50 50 –40°C to +125°C MSOP-10 RM-10 D10
AD5172BRM50-RL7 50 –40°C to +125°C MSOP-10 RM-10 D10
AD5172BRM100 100 –40°C to +125°C MSOP-10 RM-10 D11
AD5172BRM100-RL7 100 –40°C to +125°C MSOP-10 RM-10 D11
AD5172EVAL1 Evaluation Board
AD5173BRM2.5 2.5 –40°C to +125°C MSOP-10 RM-10 D1K
AD5173BRM2.5-RL7 2.5 –40°C to +125°C MSOP-10 RM-10 D1K
AD5173BRM10 10 –40°C to +125°C MSOP-10 RM-10 D1L
AD5173BRM10-RL7 10 –40°C to +125°C MSOP-10 RM-10 D1L
AD5173BRM50 50 –40°C to +125°C MSOP-10 RM-10 D1M
AD5173BRM50-RL7 50 –40°C to +125°C MSOP-10 RM-10 D1M
AD5173BRM100 100 –40°C to +125°C MSOP-10 RM-10 D1N
AD5173BRM100-RL7 100 –40°C to +125°C MSOP-10 RM-10 D1N
AD5173EVAL1 Evaluation Board
1 The evaluation board is shipped with the 10 kΩ RAB resistor option; however, the board is compatible with all available resistor value options.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
© 2003 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C04103–0–11/03(A)
