NCV891330 Step-Down Regulator Automotive, Low-Iq, Dual-Mode 3 A, 2 MHz www.onsemi.com The NCV891330 is a Dual Mode regulator intended for Automotive, battery-connected applications that must operate with up to a 45 V input supply. Depending on the output load, it operates either as a PWM Buck Converter or as a Low Drop-Out Linear Regulator, and is suitable for systems with low noise and Low Quiescent Current requirements often encountered in automotive driver information systems. A reset pin (with fixed delay) simplifies interfacing with a microcontroller. The NCV891330 also provides several protection features expected in automotive power supply systems such as current limit, short circuit protection, and thermal shutdown. In addition, the high switching frequency produces low output voltage ripple even when using small inductor values and an all-ceramic output filter capacitor - forming a space-efficient switching regulator solution. 8 1 SOIC-8 EXPOSED PAD CASE 751AC MARKING DIAGRAM 8 891330XX ALYW G Features * * * * * * * * * * * 30 mA Iq in Light Load Condition 3.0 A Maximum Output Current in PWM Mode Internal N-channel Power Switch VIN Operating Range 3.7 V to 36 V Withstands Load Dump to 45 V Logic Level Enable Pin can be Tied to Battery Fixed Output Voltage of 5.0 V, 4.0 V, 3.8 V or 3.3 V 2 MHz Free-running Switching Frequency 2 % Output Voltage Accuracy NCV Prefix for Automotive Requiring Site and Control Changes These Devices are Pb-Free and are RoHS Compliant Typical Applications * * * * Audio Infotainment Instrumentation Safety-Vision Systems NCV891330 VIN CIN RESET CDRV VIN SW DRV BST RSTB GND L1 PIN CONNECTIONS VIN 1 8 SW DRV 2 7 BST RSTB 3 6 VOUT GND 4 5 EN VOUT DFW COUT VOUT EN With XX = 33 for 3.3 V Output = 38 for 3.8 V Output = 40 for 4.0 V Output = 50 for 5.0 V Output A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb-Free Device (Top View) DBST CBST 1 ORDERING INFORMATION See detailed ordering and shipping information on page 15 of this data sheet. EN Figure 1. Typical Application (c) Semiconductor Components Industries, LLC, 2015 August, 2019 - Rev. 3 1 Publication Order Number: NCV891330/D NCV891330 CDRV DBST VIN VIN CIN SW 3.3 V Reg VOUT Enable comp Soft-Start RESET EN EN + Switcher Supply ON MODE SELECTION LINEAR REGULATOR ON OVLD GND + - RESET VOLTAGES MONITORS 3A detector + - + - + +S TSD COUT BST Low PWM LOGIC ON OFF Oscillator RSTB DFW CBST DRV VOUT L1 + Logic NCV891330 Figure 2. Simplified Block Diagram Table 1. PIN FUNCTION DESCRIPTION Pin No. Pin Name 1 VIN Input voltage from battery. Place an input filter capacitor in close proximity to this pin. 2 DRV Output voltage to provide a regulated voltage to the Power Switch gate driver. 3 RSTB Reset function. Open drain output, pulling down to ground when the output voltage is out of regulation. 4 GND Battery return, and output voltage ground reference. 5 EN This TTL compatible Enable input allows the direct connection of Battery as the enable signal. Grounding this input stops switching and reduces quiescent current draw to a minimum. 6 VOUT Output voltage feedback and LDO output. Feedback of output voltage used for regulation, as well as LDO output in LDO mode. 7 BST Bootstrap input provides drive voltage higher than VIN to the N-channel Power Switch for minimum switch Rdson and highest efficiency. 8 SW Switching node of the Regulator. Connect the output inductor and cathode of the freewheeling diode to this pin. EPAD Description Connect to Pin 4 (electrical ground) and to a low thermal resistance path to the ambient temperature environment. www.onsemi.com 2 NCV891330 Table 2. ABSOLUTE MAXIMUM RATINGS Rating Symbol Min/Max Voltage VIN Value Unit -0.3 to 45 V 45 V -0.7 to 40 V Max Voltage VIN to SW Min/Max Voltage SW Min Voltage SW - 20 ns -3.0 V Min/Max Voltage EN -0.3 to 40 V Min/Max Voltage BST -0.3 to 43 V Min/Max Voltage BST to SW -0.3 to 3.6 V Min/Max Voltage on RSTB -0.3 to 6 V Min/Max Voltage VOUT -0.3 to 18 V Min/Max Voltage DRV Thermal Resistance, SOIC8-EP Junction-to-Ambient (Note 1) -0.3 to 3.6 V 30 C/W -55 to +150 C TJ -40 to +150 C VESD 2.0 kV MSL Level 2 RJA Storage Temperature range Operating Junction Temperature Range ESD withstand Voltage (Note 2) Human Body Model Moisture Sensitivity Peak Reflow Soldering Temperature (Note 3) 260 C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Value based on 4 layers of 645 mm2 (or 1 in2) of 1 oz copper thickness on FR4 PCB substrate. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AEC-Q100-002 (EIA/JESD22-A114) Latchup Current Maximum Rating: v150 mA per JEDEC standard: JESD78 3. For information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D Table 3. ELECTRICAL CHARACTERISTICS VIN = 4.5 to 28 V, VEN = 5 V, VBST = VSW + 3 V, CDRV = 0.1 mF, for typical values TJ = 25C, Min/Max values are valid for the temperature range -40C v TJ v 150C unless noted otherwise, and are guaranteed by test, design or statistical correlation (Notes 4, 5) Parameter Test Conditions Symbol Min Typ Max Unit Iq 30 39 mA IqSD 9 12 mA QUIESCENT CURRENT Quiescent Current, enabled VIN = 13.2 V, IOUT = 100 mA, 25C Quiescent Current, shutdown VIN = 13.2 V, VEN = 0 V, 25C UNDERVOLTAGE LOCKOUT - VIN (UVLO) UVLO Start Threshold VIN rising VUVLSTT 4.1 4.5 V UVLO Stop Threshold VIN falling VUVLSTP 3.1 3.7 V VUVLOHY 0.4 1.4 V tSS 0.8 1.4 2.0 ms 4.9 3.92 3.724 3.234 5.0 4.0 3.8 3.3 5.1 4.08 3.876 3.366 1.8 0.9 2.0 1.0 2.2 1.1 UVLO Hysteresis SOFT-START (SS) Soft-Start Completion Time OUTPUT VOLTAGE Output Voltage during regulation 100 mA < IOUT < 2.5 A 5.0 V option 4.0 V option 3.8 V option 3.3 V option VOUTreg 4.5 < VIN < 18 V 20 V <VIN < 28V FSW FSW(HV) V OSCILLATOR Frequency MHz 4. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 5. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. www.onsemi.com 3 NCV891330 Table 3. ELECTRICAL CHARACTERISTICS VIN = 4.5 to 28 V, VEN = 5 V, VBST = VSW + 3 V, CDRV = 0.1 mF, for typical values TJ = 25C, Min/Max values are valid for the temperature range -40C v TJ v 150C unless noted otherwise, and are guaranteed by test, design or statistical correlation (Notes 4, 5) Parameter Test Conditions Symbol Min Frequency Foldback Threshold VIN rising VIN falling VFLDUP VFLDDN 18.4 18 Frequency Foldback Hysteresis VFLDHY 0.2 INtoL 3 Typ Max Unit VIN FREQUENCY FOLDBACK MONITOR 20 19.8 0.3 V 0.4 V 40 mA MODE TRANSITION Normal to Low-Iq mode Current Threshold 8 V < VIN < 28 V Mode Transition Duration Switcher to Linear Linear to Switcher Minimum time in Normal Mode before starting to monitor output current Linear to switcher transition at high Vin at low Vin VOUT = 3.3 V tSWtoLIN tLINtoSW 300 1 tSWblank 500 VLINtoSW(HV) VLINtoSW(LV) 19 3.6 ms 2 ms 28 4.5 V PEAK CURRENT LIMIT ILIM Current Limit Threshold 3.9 4.4 4.9 A 180 360 mW 10 mA 70 ns POWER SWITCH ON Resistance VBST = VSW + 3.0 V RDSON Leakage current VIN to SW VSW = 0, -40C v TJ v 85C ILKSW Minimum ON Time Measured at SW pin tONMIN Minimum OFF Time Measured at SW pin At FSW = 2 MHz (normal) At FSW = 500 kHz (max duty cycle) tOFFMIN 45 ns 30 30 50 70 1.45 0.65 2.0 1.0 2.8 1.3 A/ms 5 25 mV 35 mV SLOPE COMPENSATION 4.5 < VIN < 18 V 20 V <VIN < 28V Sramp Sramp(HV) Line Regulation IOUT = 5 mA, 6 V < VIN < 18 V VREG(line) Load Regulation VIN = 13.2 V, 0.1 mA < IOUT < 50 mA VREG(load) 5 Power Supply Rejection VOUT(ripple) = 0.5 Vp-p, F = 100 Hz PSRR 65 Ramp Slope (With respect to switch current) LOW POWER LINEAR REGULATOR Current Limit Output clamp current ILIN(lim) 50 VOUT = VOUTreg(typ) + 10% ICL(OUT) 0.5 VOUT = 0 V, 4.5 V < VIN < 18 V VOUT = 0 V, 20 V <VIN < 28 V FSWAF FSWAFHV FSWHIC 450 225 24 dB 80 mA 1.0 1.5 mA 550 275 32 650 325 40 SHORT CIRCUIT DETECTOR Switching frequency in short-circuit condition Analog Foldback Analog foldback - high VIN Hiccup Mode kHz RESET Leakage current into RSTB pin IRSTBlk Output voltage threshold at which the RSTB VOUT decreasing signal goes low 5.0 V option 4.0 V option 3.8 V option 3.3 V option VRESET 1 4.50 3.6 3.42 2.97 4.625 3.7 3.515 3.05 4.75 3.8 3.61 3.14 uA V 4. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 5. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. www.onsemi.com 4 NCV891330 Table 3. ELECTRICAL CHARACTERISTICS VIN = 4.5 to 28 V, VEN = 5 V, VBST = VSW + 3 V, CDRV = 0.1 mF, for typical values TJ = 25C, Min/Max values are valid for the temperature range -40C v TJ v 150C unless noted otherwise, and are guaranteed by test, design or statistical correlation (Notes 4, 5) Parameter Test Conditions Symbol Min Typ Max 25 20 19 17 60 50 45 40 100 80 76 66 Unit RESET Hysteresis on RSTB threshold VOUT increasing 5.0 V option 4.0 V option 3.8 V option 3.3 V option VREShys Noise-filtering delay From VOUT<VRESET to RSTB pin going low tfilter 10 Restart Delay time From VOUT>VRESET+VREShys to high RSTB tdelay 14 Low RSTB voltage RRSTBpullup = VOUTreg/1 mA, VOUT > 1 V VRSTBlow 16 mV 25 ms 18 ms 0.4 V GATE VOLTAGE SUPPLY (DRV pin) VDRV 3.1 3.3 3.5 V DRV UVLO START Threshold VDRVSTT 2.7 2.9 3.05 V DRV UVLO STOP Threshold VDRVSTP 2.5 2.8 3.0 V DRV UVLO Hysteresis VDRVHYS 50 200 mV IDRVLIM 21 50 mA Output Voltage DRV Current Limit VDRV = 0 V VIN OVERVOLTAGE SHUTDOWN MONITOR Overvoltage Stop Threshold VIN increasing VOVSTP 36.5 37.7 39.0 V Overvoltage Start Threshold VIN decreasing VOVSTT 36.0 37.3 38.8 V VOVHY 0.25 0.40 0.50 V Logic low threshold voltage VENlow 0.8 Logic high threshold voltage VENhigh 2 V EN pin input current IENbias 0.2 1 mA TSD 155 190 C TSDrestart 135 185 C THYS 5 20 C Overvoltage Hysteresis ENABLE (EN) V THERMAL SHUTDOWN Activation Temperature Reset temperature Hysteresis 4. Refer to ABSOLUTE MAXIMUM RATINGS and APPLICATION INFORMATION for Safe Operating Area. 5. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 5 NCV891330 TYPICAL CHARACTERISTICS 1000 70 INPUT CURRENT (mA) NO LOAD INPUT CURRENT (mA) 80 60 50 40 30 20 0 5 10 15 400 200 0 20 0 200 400 600 800 1000 INPUT VOLTAGE (V) OUTPUT CURRENT (mA) Figure 3. No-load Input Current at TJ = 255C vs. Input Voltage Figure 4. Input Current at TJ = 255C vs. Output Current 13 Iq IN SHUTDOWN MODE (mA) 100 Iq IN LOW-Iq LINEAR MODE (mA) 600 10 0 80 60 40 20 0 -50 0 50 100 12 11 10 9 8 7 -50 150 0 50 100 150 TEMPERATURE (C) TEMPERATURE (C) Figure 5. Low-Iq Mode Quiescent Current vs. Junction Temperature Figure 6. Shutdown Mode Quiescent Current vs. Junction Temperature 1.6 3.36 3.3 V OUTPUT VOLTAGE (V) Iq IN SWITCHER MODE (mA) 800 1.5 1.4 1.3 1.2 -50 0 50 100 3.34 3.32 Switcher Mode 3.30 3.28 3.26 3.24 -50 150 Low-Iq Mode 0 50 100 TEMPERATURE (C) TEMPERATURE (C) Figure 7. Switching Mode Quiescent Current vs. Junction Temperature Figure 8. 3.3 V Output Voltage vs. Junction Temperature www.onsemi.com 6 150 NCV891330 TYPICAL CHARACTERISTICS 5.05 5.04 4.03 5.03 5 V OUTPUT VOLTAGE (V) 4 V OUTPUT VOLTAGE (V) 4.05 4.04 4.02 4.01 Switcher Mode 4.00 3.99 Low-Iq Mode 3.98 3.97 3.96 3.95 3.94 -50 0 50 100 150 Switcher Mode 4.99 4.98 Low-Iq Mode 4.97 4.96 0 50 100 150 TEMPERATURE (C) TEMPERATURE (C) Figure 9. 4.0 V Output Voltage vs. Junction Temperature Figure 10. 5.0 V Output Voltage vs. Junction Temperature 57 MINIMUM ON TIME (ns) SWITCHING FREQUENCY (MHz) 5.00 4.95 4.94 -50 2.2 2.1 2.0 1.9 1.8 -50 0 50 100 56 55 54 53 52 -50 150 0 50 100 TEMPERATURE (C) TEMPERATURE (C) Figure 11. Switching Frequency vs. Junction Temperature Figure 12. Minimum On Time vs. Junction Temperature PEAK CURRENT LIMIT (A) 54 52 50 48 -50 150 4.7 56 MINIMUM OFF TIME (ns) 5.02 5.01 0 50 100 4.6 4.5 4.4 4.3 4.2 -50 150 0 50 100 TEMPERATURE (C) TEMPERATURE (C) Figure 13. Minimum Off Time vs. Junction Temperature Figure 14. Peak Current Limit vs. Junction Temperature www.onsemi.com 7 150 NCV891330 TYPICAL CHARACTERISTICS 4.6 4.4 UVLO THRESHOLDS (V) OVERVOLTAGE THRESHOLDS (V) 40 Start-up Threshold 4.2 4.0 3.8 3.6 UVLO Threshold 3.4 3.2 3.0 -50 0 50 100 Restart Threshold 36 35 0 50 100 150 Figure 15. UVLO Thresholds vs. Junction Temperature Figure 16. Input Overvoltage Thresholds vs. Junction Temperature 3.5 3.4 DRV VOLTAGE (V) 1.50 1.45 IDRV = 0 mA 3.3 IDRV = 21 mA 3.2 3.1 0 50 100 3.0 -50 150 0 50 100 TEMPERATURE (C) TEMPERATURE (C) Figure 17. Soft-start Duration vs. Junction Temperature Figure 18. DRV Voltage vs. Junction Temperature FREQUENCY FOLDBACK VIN THRESHOLDS (V) SOFT-START TIME (ms) 37 TEMPERATURE (C) 3.0 DRV UVLO THRESHOLDS (V) Overvoltage Threshold TEMPERATURE (C) 1.55 DRV Start-up Threshold 2.9 2.8 DRV UVLO Threshold 2.7 2.6 -50 38 34 -50 150 1.60 1.40 -50 39 0 50 100 150 TEMPERATURE (C) 19.8 19.6 19.4 VIN Rising 19.2 19.0 18.8 VIN Falling 18.6 18.4 18.2 18.0 -50 Figure 19. DRV Voltage UVLO Tresholds vs. Junction Temperature 0 50 100 TEMPERATURE (C) Figure 20. Frequency Foldback Voltage Tresholds vs. Junction Temperature www.onsemi.com 8 150 150 NCV891330 1.10 3.3 V RESET VOUT THRESHOLDS (V) SWITCHING FREQUENCY AT HIGH VIN (MHz) TYPICAL CHARACTERISTICS 1.05 1.00 0.95 0.90 -50 0 50 100 150 RSTB Toggles High (VOUT Rising) 3.1 RSTB Toggles Low (VOUT Falling) 3.0 2.9 2.8 -50 0 50 100 150 TEMPERATURE (C) Figure 21. Foldback Frequency vs. Junction Temperature Figure 22. 3.3 V Version RESET Thresholds vs. Junction Temperature 5 V RESET VOUT THRESHOLDS (V) 5.0 3.9 3.8 RSTB Toggles High (VOUT Rising) 3.7 RSTB Toggles Low (VOUT Falling) 3.6 3.5 3.4 -50 0 50 100 150 4.9 4.8 RSTB Toggles High (VOUT Rising) 4.7 4.6 RSTB Toggles Low (VOUT Falling) 4.5 4.4 4.3 -50 0 50 100 150 TEMPERATURE (C) TEMPERATURE (C) Figure 23. 4.0 V Version RESET Thresholds vs. Junction Temperature Figure 24. 5.0 V Version RESET Thresholds vs. Junction Temperature 17.0 71 16.8 69 LINEAR TO SWITCHER MODE CURRENT THRESHOLD (mA) 4 V RESET VOUT THRESHOLDS (V) 3.2 TEMPERATURE (C) 4.0 RESET DELAY (ms) 3.3 16.6 16.4 16.2 16.0 15.8 15.6 15.4 -50 0 50 100 67 65 63 61 59 57 55 -50 150 0 50 100 150 TEMPERATURE (C) TEMPERATURE (C) Figure 25. RESET Delay vs. Junction Temperature Figure 26. Low-Iq to Switcher Mode Transition vs. Junction Temperature www.onsemi.com 9 NCV891330 30 CURRENT RANGE FOR LOW-Iq TRANSITION - 5 V VERSION (mA) CURRENT RANGE FOR LOW-Iq TRANSITION - 3.3 V VERSION (mA) TYPICAL CHARACTERISTICS 20 10 0 30 20 10 0 5 10 15 18 5 10 15 18 INPUT VOLTAGE (V) INPUT VOLTAGE (V) Figure 27. Switcher to Low-Iq Mode Transition (3.3 V Version, 2.2 mH) vs. Input Voltage Figure 28. Switcher to Low-Iq Mode Transition (5.0 V Version, 2.2 mH) vs. Input Voltage www.onsemi.com 10 NCV891330 APPLICATION INFORMATION Hybrid Low-Power Mode converter mode. This transition happens in less than 2 ms, so that the transient response is not affected by the mode change. Once the NCV891330 has transitioned to switcher mode, it cannot go back to low-Iq mode before a 500 ms blanking period has elapsed, after which it starts looking at the output current level. If the NCV891330 is in low-Iq Linear Regulator mode in normal battery range, it will transition to switcher mode when VIN increases above VLINtoSW(HV), regardless of the output current. Similarly, if the NCV891330 is in PWM mode and VIN is higher than VFLDUP, it will not transition to low-Iq Linear mode even if the output current becomes lower than INtoL. At low input voltage, the NCV891330 stays in low-Iq mode down to VLINtoSW(LV) if it entered this mode while in normal battery range. However it may not enter low-Iq mode below 8 V depending on the charge of the bootstrap capacitor (see Bootstrap section and typical characteristics curves for details). A high-frequency switch-mode regulator is not very efficient in light load conditions, making it difficult to achieve low-Iq requirements for sleep-mode operation. To remedy this, the NCV891330 includes a low-Iq linear regulator that turns on at light load, while the PWM regulator turns off, ensuring a high-efficiency low-power operation. Another advantage of linear mode is the tight regulation free of voltage ripple usually associated with low-Iq switchers in light load conditions. At initial start-up the NCV891330 always runs in PWM converter mode, regardless of the output current, and goes through a soft start. It then stays in PWM mode if the output current is high enough. If the output current is low, the NCV891330 transitions to Linear Regulator mode, after a 300 ms period during which it assesses the level of ouput current. Note that the Reset signal needs to be high before the IC starts to look at the output current level. It stays in this low-power mode until the output current exceeds the ILIN(lim) limit: it then transitions to PWM LOW-IQ NO MODE TRANSITION MODE SWITCH INtoL 3 mA 40 mA ILIN(lim) 50 mA Output Current 80 mA IOUT Figure 29. Mode Transition Diagram for Input Voltages between 8.0 V and VLINtoSW(HV) www.onsemi.com 11 NCV891330 Input Voltage An overvoltage monitoring circuit automatically terminates switching if the input voltage exceeds VOVSTP (see Figure 30), but the NCV891330 can withstand input voltages up to 45 V. To avoid skipping switching pulses and entering an uncontrolled mode of operation, the switching frequency is reduced by a factor of 2 when the input voltage exceeds the VIN Frequency Foldback threshold (see Figure 30). Frequency reduction is automatically terminated when the input voltage drops back below the VIN Frequency Foldback threshold. This also helps to limit the power lost in switching and generating the drive voltage for the Power Switch. An Undervoltage Lockout (UVLO) circuit monitors the input. The circuit can inhibit switching and reset the Soft-start circuit if there is insufficient voltage for proper regulation. Depending on the output conditions (voltage option and loading), the NCV891330 may lose regulation and run in drop-out mode before reaching the UVLO threshold: refer to the Minimum Vin calculation tool for details. When the input voltage drops low enough that the part cannot regulate because it reaches its maximum duty cycle, the switching frequency is divided down by up to 4 (down to 500 kHz). This helps lowering the minimum voltage at which the regulator loses regulation. FSW (MHz) 2 1 Frequency folds back if drop-out mode 3.5 18 20 36 39 45 V IN (V) Figure 30. NCV891330 Switching Frequency Profile vs. Input Voltage Soft-Start compensation signal requires the inductor to be greater than a minimum value, depending on output voltage, in order to avoid sub-harmonic oscillations. The recommended inductor values are 2.2 or 3.3 mH, although higher values are possible. Upon being enabled or released from a fault condition, and after the DRV voltage is established, a soft-start circuit ramps the switching regulator error amplifier reference voltage to the final value. During soft-start, the average switching frequency is lower until the output voltage approaches regulation. Current Limiting Due to the ripple on the inductor current, the average output current of a buck converter is lower than the peak current setpoint of the regulator. Figure 31 shows - for a 2.2 mH inductor - how the variation of inductor peak current with input voltage affects the maximum DC current the NCV891330 can deliver to a load. Slope Compensation A fixed slope compensation signal is generated internally and added to the sensed current to avoid increased output voltage ripple due to bifurcation of inductor ripple current at duty cycles above 50%. The fixed amplitude of the slope www.onsemi.com 12 NCV891330 Figure 31. NCV891330 Load Current Capability with a 2.2 mH Inductor Short Circuit Protection The RSTB pin is also pulled low immediately in case of VIN overvoltage, Thermal shutdown, VIN UVLO or DRV UVLO. During severe output overloads or short circuits, the NCV891330 automatically reduces its switching frequency. This creates duty cycles small enough to limit the peak current in the power components, while maintaining the ability to automatically reestablish the output voltage if the overload is removed. In more severe short-circuit conditions where the inductor current is still too high after the switching frequency has fully folded back, the regulator enters a hiccup mode that further reduces the power dissipation and protects the system. Feedback Loop All components of the feedback loop (output voltage sensing, error amplifier and compensation) are integrated inside the NCV891330, and are optimized to ensure regulation and sufficient phase and gain margin for the recommended conditions of operation. Recommended conditions and components: * Input: car battery * Output: 3.3 V, 3.8 V, 4 V or 5 V, with output current up to 3 A * Output capacitor: 30 mF capacitance * Inductor: 2.2 mH to 3.3 mH With these operating conditions and components, the open loop transfer function has a phase margin greater than 50, as can be seen in Figure 32. RESET Function The RSTB pin is pulled low when the output voltage falls below 7.5% of the nominal regulation level, and floats when the output is properly regulated. A pull-up resistor tied to the output is needed to generate a logic high signal on this open drain pin. The pin can be left unconnected when not used. When the output voltage drops out of regulation, the pin goes low after a short noise-filtering delay (tfilter). It stays low for a 16 ms delay time after the output goes back to regulation, simplifying the connection to a micro-controller. www.onsemi.com 13 NCV891330 Figure 32. Bode Plot of the Open Loop Transfer Function of a Buck Converter using the NCV891330 for Vin = 13 V, Vout = 3.3 V, Iout = 2 A, Cout=3x10 mF and L=2.2 mH For more details and for effect of component values other than the recommended ones, please refer to the design spreadsheet provided on the www.onsemi.com NCV891330 page. The design spreadsheet also includes the total open loop transfer function for the output voltage sensing at the NCV891330 VOUT pin to the output voltage. www.onsemi.com 14 NCV891330 Bootstrap voltages above 40 V are expected, EN should be tied to VIN through a 10 kW resistor in order to limit the current flowing into the overvoltage protection of the pin. EN low induces a shutdown mode which shuts off the regulator and minimizes its supply current to 9 mA typical by disabling all functions. Upon enabling, voltage is established at the DRV pin, followed by a soft-start of the switching regulator output. At the DRV pin an internal regulator provides a ground- referenced voltage to an external capacitor (CDRV), to allow fast recharge of the external bootstrap capacitor (CBST) used to supply power to the power switch gate driver. If the voltage at the DRV pin goes below the DRV UVLO Threshold VDRVSTP, switching is inhibited and the Soft-start circuit is reset, until the DRV pin voltage goes back up above VDRVSTT. The NCV891330 permanently monitors the bootstrap capacitor, and always ensures it stays charged no matter what the operating conditions are. As a result, the additional charging current for the bootstrap capacitor may prevent the regulator from entering Low-Iq mode at low input voltage. Practically, the 5 V output version does not enter Low-Iq mode for input voltages below 8 V, and the 3.8 V and 4 V versions for input voltages below 6.5 V (see typical characteristics curves for details). Thermal Shutdown A thermal shutdown circuit inhibits switching, resets the Soft-start circuit, and removes DRV voltage if internal temperature exceeds a safe level. Switching is automatically restored when temperature returns to a safe level. Exposed Pad The exposed pad (EPAD) on the back of the package must be electrically connected to the electrical ground (GND pin) for proper, noise-free operation. Enable The NCV891330 is designed to accept either a logic level signal or battery voltage as an Enable signal. However if ORDERING INFORMATION Device Output NCV891330PD50R2G 5.0 V NCV891330PD40R2G 4.0 V NCV891330PD38R2G 3.8 V NCV891330PD33R2G 3.3 V Package Shipping SOIC-8 EP (Pb-Free) 2500 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 15 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOIC-8 EP CASE 751AC ISSUE D 8 1 SCALE 1:1 DATE 02 APR 2019 GENERIC MARKING DIAGRAM* 8 XXXXX AYWWG G 1 DOCUMENT NUMBER: DESCRIPTION: XXXXXX = Specific Device Code A = Assembly Location Y = Year WW = Work Week G = Pb-Free Package 98AON14029D SOIC-8 EP *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G" or microdot " G", may or may not be present and may be in either location. Some products may not follow the Generic Marking. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2018 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative