2N656575 - Littelfuse, Inc. - Datasheet.Global

163

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Description

Excellent unidirectional switches for phase control

applications such as heating and motor speed controls.

Sensitive gate SCRs are easily triggered with microAmps

of current as furnished by sense coils, proximity switches,

and microprocessors.

Features & Beneﬁts

• RoHS compliant

• Glass – passivated

junctions

• Voltage capability up

to 600 V

• Surge capability up to

20 A

Schematic Symbol

Main Features

Symbol Value Unit

IT(RMS) 0.8 A

VDRM /VRRM 400 to 600 V

IGT 12 to 500 μA

Absolute Maximum Ratings — Sensitive SCRs

Symbol Parameter Test Conditions Value Unit

IT(RMS) RMS on-state current TC = 75°C 0.8 A

IT(AV) Average on-state current TC = 75°C 0.51 A

ITSM Peak non-repetitive surge current

single half cycle; f = 50Hz;

TJ (initial) = 25°C 16

single half cycle; f = 60Hz;

TJ (initial) = 25°C 20

I2t I2t Value for fusing tp = 8.3 ms 1. 6 A2s

di/dt Critical rate of rise of on-state current f = 60 Hz ; TJ = 110°C 50 A/μs

IGM Peak gate current TJ = 110°C 1 A

PG(AV) Average gate power dissipation TJ = 110°C 0.1 W

Tstg Storage temperature range -40 to 150 °C

TJOperating junction temperature range -40 to 110 °C

Applications

Typical applications are capacitive discharge systems

for strobe lights and gas engine ignition. Also controls

for power tools, home/brown goods and white goods

appliances.

164

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Electrical Characteristics (TJ = 25°C, unless otherwise speciﬁed)

Symbol Test Conditions

Value

Unit

SxS1

EC103X1

SxS2

EC103X2

SxS /

2N6565

EC103X

SxS3

EC103X3

IGT VD = 6V; RL = 100 Ω

MAX. 12 50 200 500 µA

VGT MAX. 0.8 V

dv/dt VD = VDRM; RGK = 1kΩ

400V

MIN.

20 25 30 40

V/μs

600V 10 10 15 20

VGD VD = VDRM; RL = 3.3 kΩ; TJ = 110°C MIN. 0.2 0.25 V

IHIT = 20mA (initial), RGK = 1kΩ MAX. 5 8 mA

tq(1) MAX. 60 50 45 μs

tgt IG = 2 x IGT; PW = 15µs; IT = 1.6A TYP. 2 5 20 30 μs

(1) IT=1A; tp=50µs; dv/dt=5V/µs; di/dt=-5A/µs

Static Characteristics

Symbol Test Conditions Value Unit

VTM IT = 1.2A; tp = 380 µs MAX. 1. 7 V

IDRM / IRRM

VDRM = VRRM

RGK = 1kΩ

TJ = 25°C

MAX.

μATJ = 100°C 50

TJ = 110°C 100

Thermal Resistances

Symbol Parameter Value Unit

Rθ(J-C) Junction to case (AC)

EC103xy/2N6565 75

°C/W

SxSy 60*

Rθ(J-A) Junction to ambient EC103xy/2N6565 160 °C/W

Notes: x = voltage, y = sensitivity

* = Mounted on 1 cm2 copper (two-ounce) foil surface

165

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Figure 1: Normalized DC Gate Trigger Current

vs. Junction Temperature

Figure 2: Normalized DC Gate Trigger Voltage

vs. Junction Temperature

0.0

1.0

2.0

3.0

4.0

-40 -15 10 35 60 85 110

Junction Temperature (TJ) -- (°C)

Ratio of I

= 25°C)

Figure 5: Power Dissipation (Typical)

vs. RMS On-State Current

Figure 6: Maximum Allowable Case Temperature

vs. RMS On-State Current

Figure 3: Normalized DC Holding Current

vs. Junction Temperature

Figure 4: On-State Current vs. On-State

Voltage (Typical)

0.0

0.5

1.0

1.5

2.0

-40 -15 10 35 60 85 110

Junction Temperature (T

) -- (°C)

Ratio of V

/ V

= 25ºC)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

-40 -15 10 35 60 85 110

Junction Temperature (T

) -- (°C)

Ratio of IH / IH (TJ = 25°C)

= 25°C

0.70.8 0.91.0 1.11.2 1.31.4 1.51.6

Instantaneous On-state Voltage (vT) – Volts

Instantaneous On-state Current (iT) – Amps

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

Average On-State Power Dissipation

D(AV)

] - (Watts)

RMS On-State Current [IT(RMS)] - Amps

105

115

0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

RMS On-State Current [IT(RMS)] - Amps

Maximum Allowable Case Temperature

(TC) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

166

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Figure 7: Maximum Allowable Case Temperature

vs. Average On-State Current

Figure 8: Maximum Allowable Ambient Temperature

vs. RMS On-State Current

Figure 9: Maximum Allowable Ambient Temperature

vs. Average On-State Current

105

115

0.0 0.1 0.2 0.3 0.4 0.5 0.6

Average On-State Current [IT(AVE)] - Amps

Maximum Allowable Case Temperature

(TC) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

100

120

0.00.1 0.20.3 0.40.5 0.60.7 0.80.9 1.0

RMS On-State Current [I

T(RMS)

] - Amps

Maximum Allowable Ambient Temperature

) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

FREE AIR RATING

100

120

0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7

Average On-State Current [IT(AVE)] - Amps

Maximum Allowable Ambient Temperature

(TA) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

FREE AIR RATING

Figure 11: Peak Repetitive Sinusoidal Pulse Current

Figure 10: Peak Capacitor Discharge Current

Pulse Current Duration (tW) - μs

Peak Discharge Current (I

) -Amps

100

120

140

160

180

1 Hz

12 Hz

60 Hz

ITRM

100

120

140

160

180

Pulse Current Duration (tW) - μs

Peak Discharge Current (ITM) - Amps

1 Hz

12 Hz

60 Hz

167

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

0.1

1.0

10.0

100.0

110 100 1000

Surge Current Duration -- Full Cycles

Peak Surge (Non-repetitive)

On-state Current (ITSM) – Amps

Figure 12: Surge Peak On-State Current vs. Number of Cycles

Figure 13: Simple Test Circuit for Gate Trigger Voltage and Current

SUPPLY FREQUENCY: 60 Hz Sinusoidal

LOAD: Resistive

RMS On-State Current: [IT(RMS)]: Maximum Rated

Value at Specied Case Temperature

Notes:

1. Gate control may be lost during and immediately

following surge current interval.

2. Overload may not be repeated until junction

temperature has returned to steady-state

rated value.

Note: V1 — 0 V to 10 V dc meter

VGT — 0 V to 1 V dc meter

IG — 0 mA to 1 mA dc milliammeter

R1 — 1 k potentiometer

To measure gate trigger voltage and current, raise gate

voltage (VGT) until meter reading V1 drops from 6 V to 1 V.

Gate trigger voltage is the reading on VGT just prior to V1

dropping. Gate trigger current IGT Can be computed from

the relationship

VGT

IGT = IG- ____

Amps

1000

where IG is reading (in amperes) on meter just prior to V1

dropping

Note: IGT may turn out to be a negative quantity (trigger

current ﬂows out from gate lead). If negative current

occurs, IGT value is not a valid reading. Remove 1 k resistor

and use IG as the more correct IGT value. This will occur on

12 µA gate products.

Reset

Normally-closed

Pushbutton

6VDC

–

D.U.T.

100

1 k

(1%)

100

IGT

IN4001

VGT

168

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Soldering Parameters

Reﬂow Condition Pb – Free assembly

Pre Heat

- Temperature Min (Ts(min))150°C

- Temperature Max (Ts(max))200°C

- Time (min to max) (ts)60 – 180 secs

Average ramp up rate (Liquidus Temp)

(TL) to peak 5°C/second max

TS(max) to TL - Ramp-up Rate 5°C/second max

Reﬂow - Temperature (TL) (Liquidus) 217°C

- Temperature (tL)60 – 150 seconds

Peak Temperature (TP)260+0/-5 °C

Time within 5°C of actual peak

Temperature (tp)20 – 40 seconds

Ramp-down Rate 5°C/second max

Time 25°C to peak Temperature (TP)8 minutes Max.

Do not exceed 280°C

Physical Speciﬁcations Environmental Speciﬁcations

Test Speciﬁcations and Conditions

AC Blocking MIL-STD-750, M-1040, Cond A Applied

Peak AC voltage @ 110°C for 1008 hours

Temperature Cycling

MIL-STD-750, M-1051,

100 cycles; -40°C to +150°C; 15-min

dwell-time

Temperature/

Humidity

EIA / JEDEC, JESD22-A101

1008 hours; 320V - DC: 85°C; 85%

rel humidity

High Temp Storage MIL-STD-750, M-1031,

1008 hours; 150°C

Low-Temp Storage 1008 hours; -40°C

Thermal Shock

MIL-STD-750, M-1056

10 cycles; 0°C to 100°C; 5-min dwell-

time at each temperature; 10 sec (max)

transfer time between temperature

Autoclave

EIA / JEDEC, JESD22-A102

168 hours (121°C at 2 ATMs) and

100% R/H

Resistance to

Solder Heat MIL-STD-750 Method 2031

Solderability ANSI/J-STD-002, category 3, Test A

Lead Bend MIL-STD-750, M-2036 Cond E

Terminal Finish 100% Matte Tin-plated/Pb-free Solder

Dipped

Body Material UL recognized epoxy meeting ammability

classication 94V-0

Lead Material Copper Alloy

Design Considerations

Careful selection of the correct device for the application’s

operating parameters and environment will go a long way

toward extending the operating life of the Thyristor. Good

design practice should limit the maximum continuous

current through the main terminals to 75% of the device

rating. Other ways to ensure long life for a power discrete

semiconductor are proper heat sinking and selection of

voltage ratings for worst case conditions. Overheating,

overvoltage (including dv/dt), and surge currents are

the main killers of semiconductors. Correct mounting,

soldering, and forming of the leads also help protect

against component damage.

Time

Temperature

TS(max)

TS(min)

time to peak temperature

Preheat

eat

Ramp-upRamp-up

Ramp-down

169

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Dimensions – TO-92 (E Package)

Dimensions — Compak (C Package)

Dimension Inches Millimeters

Min Max Min Max

A 0.176 0.196 4.47 4.98

B 0.500 - 12.70 -

D 0.095 0.105 2.41 2.67

E 0.150 - 3.81 -

F 0.046 0.054 1. 16 1.37

G0.135 0.145 3.43 3.68

H0.088 0.096 2.23 2.44

J 0.176 0.186 4.47 4.73

K0.088 0.096 2.23 2.44

L 0.013 0.019 0.33 0.48

M 0.013 0.017 0.33 0.43

All leads insulated from case. Case is electrically nonconductive.

TC Measuring Point

Gate

Anode

Cathode

0.079

(2.0)

0.040

(1.0)

0.030

(0.76)

0.079

(2.0)

0.079

(2.0)

0.110

(2.8)

Pad Outline

Gate

Cathode

Anode

TC / TL Temperature

Measurement Point

Dimensions are in inches

(and millimeters).

Dimension Inches Millimeters

Min Max Min Max

A 0.130 0.156 3.30 3.95

B 0.201 0.220 5.10 5.60

C 0.077 0.087 1.95 2.20

D 0.159 0.181 4.05 4.60

E 0.030 0.063 0.75 1.60

F 0.075 0.096 1.90 2.45

G0.002 0.008 0.05 0.20

H0.077 0.104 1.95 2.65

J 0.043 0.053 1.09 1.35

K0.006 0.016 0.15 0.41

L 0.030 0.055 0.76 1.40

M 0.022 0.028 0.56 0.71

N 0.027 0.033 0.69 0.84

P 0.052 0.058 1.32 1.47

170

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Packing Options

Part Number Marking Weight Packing Mode Base Quantity

EC103xy / 2N6565 EC103xy / 2N6565 0.19 g Bulk 2000

EC103xyRP EC103xy 0.19 g Reel Pack 2000

EC103xyAP EC103xy 0.19 g Ammo Pack 2000

SxSyRP SxSy 0.08 g Embossed Carrier 2500

Note: x = Voltage, y = sensitivity

TO-92 (3-lead) Reel Pack (RP) Radial Leaded Speciﬁcations

Meets all EIA-468-C Standards

0.708

(18.0)

1.6

(41.0)

0.5

(12.7) 0.1 (2.54)

0.2 (5.08)

0.236

(6.0)

0.02 (0.5)

Direction of Feed

Dimensions

are in inches

(and millimeters).

1.97

(50.0)

14.17(360.0)

Flat up

1.26

(32.0)

0.098 (2.5) MAX

Cathode Anode

Gate

0.354

(9.0)

0.157 DIA

(4.0)

Product Selector

Part Number Voltage Gate Sensitivity Type Package

400V 600V 800V 1000V

EC103 x 1 X X 12μA Sensitive SCR TO-92

EC103 x 2 X X 50μA Sensitive SCR TO-92

EC103 x X / 2N6565 X 200μA Sensitive SCR TO-92

EC103 x 3 X X 500μA Sensitive SCR TO-92

S x S1 X X 12μA Sensitive SCR Compak

S x S2 X X 50μA Sensitive SCR Compak

S x S X X 200μA Sensitive SCR Compak

S x S3 X X 500μA Sensitive SCR Compak

Note: x = Voltage

171

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Speciﬁcations

Compak Embossed Carrier Reel Pack (RP) Speciﬁcations

Meets all EIA-468-C Standards

Meets all EIA-481-1 Standards

Flat down

25 Devices per fold

CathodeAnode

Gate

Direction of Feed

Dimensions

are in inches

(and millimeters).

0.708

(18.0)

1.62

(41.2)

0.5

(12.7)

0.1 (2.54)

0.2 (5.08)

0.236

(6.0)

0.02 (0.5)

1.85

(47.0)

13.3

(338.0)

1.27

(32.2)

0.098 (2.5) MAX

12.2

(310.0)

1.85

(47.0)

0.354

(9.0)

0.157 DIA

(4.0)

8.0

Anode

Cathode

Gate

0.47

(12.0) 0.36

(9.2)

0.315

(8.0)

0.157

(4.0)

0.49

(12.4)

0.512 (13.0) Arbor

Hole Dia.

12.99

(330.0)

Dimensions

are in inches

(and millimeters).

Direction of Feed

0.059 DIA

(1.5)

Cover tape

172

Revised: June 21, 2011 04:14 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

0.8 Amp Sensitive SCRs

EC103xx & SxSx Series

Part Numbering System (TO-92) Part Marking System

Part Numbering System (Compak) Part Marking System (Compak)

TO-92 (E Package)

EC103D1

YMLXX

1 75

DEVICE TYPE

EC: TO-92 SCR

xx: Lead Form Option

CURRENT RATING

Lead Form Dimensions

103: 0.8A (TO-92)

VOLTAGE RATING

D: 400V 1: 12

M: 600V

SENSITIVITY & TYPE

EC 103 D

2: 50

A[blank]: 200

3: 500 A

2N: JEDEC

(JEDEC) 6565: 400V

YMXXX

S6S1

Compak (C Package)

DEVICE TYPE

S: Compak SCR

CURRENT RATING

S: 0.8A (Compak)

VOLTAGE RATING

4: 400V

1: 12

6: 600V

SENSITIVITY & TYPE

S6S

2: 50

A[blank]: 200

3: 500 A