LMC7211BIM5X/NOPB - Texas Instruments

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output

Check for Samples: LMC7211-N

1FEATURES APPLICATIONS

2• Tiny SOT 23-5 package saves space • Battery Powered Products

• Package is less than 1.43 mm thick • Notebooks and PDAs

• Guaranteed specs at 2.7V, 5V, 15V supplies • PCMCIA cards

• Typical supply current 7 μA at 5V • Mobile Communications

• Response time of 4 μs at 5V • Alarm and Security circuits

• Push-pull output • Direct Sensor Interface

• Input common-mode range beyond V−and V+ • Replaces amplifiers used as comparators with

better performance and lower current

• Low input current

DESCRIPTION

The LMC7211 is a micropower CMOS comparator available in the space saving SOT23-5 package. This makes

the comparator ideal for space and weight critical designs. The LMC7211 is supplied in two offset voltage

grades, 5 mV and 15 mV.

The main benefits of the Tiny package are most apparent in small portable electronic devices, such as mobile

phones, pagers, notebook computers, personal digital assistants, and PCMCIA cards. The rail-to-rail input

voltage makes the LMC7211 a good choice for sensor interfacing, such as light detector circuits, optical and

magnetic sensors, and alarm and status circuits.

The Tiny Comparator's outside dimensions (length x width x height) of 3.05mm x 3.00mm x 1.43mm allow it to fit

into tight spaces on PC boards.

See the LMC7221 for a comparator with an open-drain output.

CONNECTION DIAGRAM

Figure 1. 8-Pin SOIC-8 Figure 2. 5-Pin SOT23-5

Top View Top View

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

Absolute Maximum Ratings (1)

ESD Tolerance (2) 2 kV

Differential Input Voltage (VCC) +0.3V to (−VCC)−0.3V

Voltage at Input/Output Pin (VCC) + 0.3V to (−VCC)−0.3V

Supply Voltage (V+–V−) 16V

Current at Input Pin (3) ±5 mA

Current at Output Pin(4) (5) ±30 mA

Current at Power Supply Pin 40 mA

Lead Temperature (soldering, 10 sec) 260°C

Storage Temperature Range −65°C to +150°C

Junction Temperature(6) 150°C

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test

conditions, see the Electrical Characteristics.

(2) Human body model, 1.5 kΩin series with 100 pF.

(3) Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage rating.

(4) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in

exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30 mA over long term may adversely

affect reliability.

(5) Do not short circuit output to V+, when V+ is greater than 12V or reliability will be adversely affected.

(6) The maximum power dissipation is a function of TJ(max),θJA, and TA. The maximum allowable power dissipation at any ambient

temperature is PD= (TJ(max) −TA)/θJA.All numbers apply for packages soldered directly into a PC board.

Operating Ratings (1)

Supply Voltage 2.7 ≤VCC ≤15V

Junction Temperature Range

LMC7211AI, LMC7211BI −40°C ≤TJ≤+85°C

Thermal Resistance (θJA) SO-8 Package, 8-Pin Surface Mount 180°C/W

M05A Package, 5-Pin Surface Mount 325°C/W

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test

conditions, see the Electrical Characteristics.

2.7V Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ= 25°C, V+= 2.7V, V−= 0V, VCM = VO= V+/2. Boldface limits apply at

the temperature extremes.

Symbol Parameter Conditions LMC7211AI LMC7211BI Units

Typ (1) Limit(2) Limit(2)

VOS Input Offset Voltage 3 5 15 mV

8 18 max

TCVOS Input Offset Voltage 1.0 μV/°C

Temperature Drift

Input Offset Voltage Average See (3) 3.3 μV/Month

Drift

IBInput Current 0.04 pA

IOS Input Offset Current 0.02 pA

CMRR Common Mode Rejection 0V ≤VCM ≤2.7V 75 dB

Ratio

PSRR Power Supply Rejection Ratio 2.7V ≤V+≤15V 80 dB

AVVoltage Gain 100 dB

(1) Typical values represent the most likely parametric norm.

(2) All limits are guaranteed by testing or statistical analysis.

(3) Input offset voltage average drift is calculated by dividing the accelerated operating life VOS drift by the equivalent operational time. This

represents worst case input conditions and includes the first 30 days of drift.

Product Folder Links: LMC7211-N

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

2.7V Electrical Characteristics (continued)

Unless otherwise specified, all limits guaranteed for TJ= 25°C, V+= 2.7V, V−= 0V, VCM = VO= V+/2. Boldface limits apply at

the temperature extremes.

Symbol Parameter Conditions LMC7211AI LMC7211BI Units

Typ (1) Limit(2) Limit(2)

CMVR Input Common-Mode Voltage CMRR > 55 dB 3.0 2.9 2.9 V

Range 2.7 2.7 min

CMRR > 55 dB −0.3 −0.2 −0.2 V

0.0 0.0 max

VOH Output Voltage High Iload = 2.5 mA 2.5 2.4 2.4 V

2.3 2.3 min

VOL Output Voltage Low Iload = 2.5 mA 0.2 0.3 0.3 V

0.4 0.4 max

ISSupply Current VOUT = Low 7 12 12 μA

14 14 max

5.0V and 15.0V Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ= 25°C, V+= 5.0V and 15V, V−= 0V, VCM = VO= V+/2. Boldface limits

apply at the temperature extremes.

Symbol Parameter Conditions LMC7211AI LMC7211BI Units

Typ (1) Limit(2) Limit(2)

VOS Input Offset Voltage 3 5 15 mV

8 18 max

TCVOS Input Offset Voltage V+= 5V 1.0 μV/°C

Temperature Drift V+= 15V 4.0

Input Offset Voltage Average V+= 5V 3.3 μV/Month

Drift V+= 15V 4.0

IBInput Current 0.04 pA

IOS Input Offset Current 0.02 pA

CMRR Common Mode V+ = 5.0V 75 dB

Rejection Ration V+ = 15.0V 82 dB

PSRR Power Supply 5V ≤V+≤10V 80 dB

Rejection Ratio

AVVoltage Gain 100 dB

CMVR Input Common-Mode V+ = 5.0V 5.3 5.2 5.2 V

Voltage Range CMRR > 55 dB 5.0 5.0 min

V+ = 5.0V −0.3 −0.2 −0.2 V

CMRR > 55 dB 0.0 0.0 max

V+ = 15.0V 15.3 15.2 15.2 V

CMRR > 55 dB 15.0 15.0 min

V+ = 15.0V −0.3 −0.2 −0.2 V

CMRR > 55 dB 0.0 0.0 max

VOH Output Voltage High V+ = 5V 4.8 4.6 4.6 V

Iload = 5 mA 4.45 4.45 min

V+ = 15V 14.8 14.6 14.6 V

Iload = 5 mA 14.45 14.45 min

VOL Output Voltage Low V+ = 5V 0.2 0.40 0.40 V

Iload = 5 mA 0.55 0.55 max

V+ = 15V 0.2 0.40 0.40 V

Iload = 5 mA 0.55 0.55 max

ISSupply Current VOUT = Low 7 14 14 μA

18 18 max

(1) Typical values represent the most likely parametric norm.

(2) All limits are guaranteed by testing or statistical analysis.

Product Folder Links: LMC7211-N

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

5.0V and 15.0V Electrical Characteristics (continued)

Unless otherwise specified, all limits guaranteed for TJ= 25°C, V+= 5.0V and 15V, V−= 0V, VCM = VO= V+/2. Boldface limits

apply at the temperature extremes.

Symbol Parameter Conditions LMC7211AI LMC7211BI Units

Typ (1) Limit(2) Limit(2)

ISC Short Circuit Current Sourcing 30 mA

Sinking (3) 45 mA

(3) Do not short circuit output to V+, when V+ is greater than 12V or reliability will be adversely affected.

AC Electrical Characteristics

Unless otherwise specified, all limits guaranteed for TJ= 25°C, V+= 5V, V−= 0V, VCM = VO= V+/2. Boldface limits apply at

the temperature extreme.

Symbol Parameter Conditions LMC7211AI LMC7211BI Units

Typ (1) Limit(2) Limit(2)

trise Rise Time f = 10 kHz, Cl = 50 pF, 0.3 μs

Overdrive = 10 mV (3)

tfall Fall Time f = 10 kHz, Cl = 50 pF, 0.3 μs

Overdrive = 10 mV (3)

tPHL Propagation Delay (High f = 10 kHz, 10 mV 10 μs

to Low) (4) Cl = 50 pF (3) 100 mV 4

V+ = 2.7V, 10 mV 10 μs

f = 10 kHz, 100 mV 4

Cl = 50 pF (3)

tPLH Propagation Delay f = 10 kHz, 10 mV 6 μs

(Low to High)(4) Cl = 50p(3) 100 mV 4

V+ = 2.7V, 10 mV 7 μs

f = 10 kHz, 100 mV 4

Cl = 50 pF(3)

(1) Typical values represent the most likely parametric norm.

(2) All limits are guaranteed by testing or statistical analysis.

(3) CLincludes the probe and jig capacitance.

(4) Input step voltage for propagation delay measurement is 2V.

Product Folder Links: LMC7211-N

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

Typical Performance Characteristics

Single Supply TA= 25°C unless specified

Supply Current Supply Current

vs. vs.

Supply Voltage Temperature while Sourcing

Supply Current Output Sourcing Current

vs. vs.

Temperature while Sinking Supply Voltage

Output Sinking Current Output Sourcing Current

vs. vs.

Supply Voltage Output Voltage @ 5V

Product Folder Links: LMC7211-N

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

Typical Performance Characteristics (continued)

Single Supply TA= 25°C unless specified

Output Sinking Current Output Sourcing Current

vs. vs.

Output Voltage @ 5V Output Voltage @ 15V

Output Sinking Current

vs.

Output Voltage @ 15V Response Time for Various Input Overdrives −tPLH

Response Time for Various Input Overdrives −tPHL Response Time for Various Input Overdrives −tPLH

Product Folder Links: LMC7211-N

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

Typical Performance Characteristics (continued)

Single Supply TA= 25°C unless specified

Response Time for Various Input Overdrives −tPHL Response Time for Various Input Overdrives −tPLH

Input Bias Current

vs.

Response Time for Various Input Overdrives −tPHL Common Mode Voltage

Input Bias Current Input Bias Current

vs. vs.

Common Mode Voltage Common Mode Voltage

Product Folder Links: LMC7211-N

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

Typical Performance Characteristics (continued)

Single Supply TA= 25°C unless specified Input Bias Current

vs.

Temperature

Product Folder Links: LMC7211-N

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

APPLICATION INFORMATION

Benefits of the LMC7211 Tiny Comparator

Size. The small footprint of the SOT 23-5 packaged Tiny Comparator, (0.120 x 0.118 inches, 3.05 x 3.00 mm)

saves space on printed circuit boards, and enable the design of smaller electronic products. Because they are

easier to carry, many customers prefer smaller and lighter products.

Height. The height (0.056 inches, 1.43 mm) of the Tiny Comparator makes it possible to use it in PCMCIA type

III cards.

Simplified Board Layout. The Tiny Comparator can simplify board layout in several ways. First, by placing a

comparator where comparators are needed, instead of routing signals to a dual or quad device, long pc traces

may be avoided.

By using multiple Tiny Comparators instead of duals or quads, complex signal routing and possibly crosstalk can

be reduced.

Low Supply Current. The typical 7 μA supply current of the LMC7211 extends battery life in portable

applications, and may allow the reduction of the size of batteries in some applications.

Wide Voltage Range. The LMC7211 is characterized at 15V, 5V and 2.7V. Performance data is provided at

these popular voltages. This wide voltage range makes the LMC7211 a good choice for devices where the

voltage may vary over the life of the batteries.

Digital Outputs Representing Signal Level. Comparators provide a high or low digital output depending on the

voltage levels of the (+) and (−) inputs. This makes comparators useful for interfacing analog signals to

microprocessors and other digital circuits. The LMC7211 can be thought of as a one-bit a/d converter.

Push-Pull Output. The push-pull output of the LMC7211 is capable of both sourcing and sinking milliamp level

currents even at a 2.7 volt supply. This can allow the LMC7211 to drive multiple logic gates.

Driving LEDs (Light Emitting Diodes). With a 5 volt power supply, the LMC7211's output sinking current can

drive small, high efficiency LEDs for indicator and test point circuits. The small size of the Tiny package makes it

easy to find space to add this feature to even compact designs.

Input range to Beyond Rail to Rail. The input common mode range of the LMC7211 is slightly larger than the

actual power supply range. This wide input range means that the comparator can be used to sense signals close

to the power supply rails. This wide input range can make design easier by eliminating voltage dividers,

amplifiers, and other front end circuits previously used to match signals to the limited input range of earlier

comparators. This is useful to power supply monitoring circuits which need to sense their own power supply, and

compare it to a reference voltage which is close to the power supply voltage. The wide input range can also be

useful for sensing the voltage drop across a current sense resistor for battery chargers.

Zero Crossing Detector. Since the LMC7211's common mode input range extends below ground even when

Low Input Currents and High Input Impedance. These characteristics allow the LMC7211 to be used to sense

high impedance signals from sensors. They also make it possible to use the LMC7211 in timing circuits built with

large value resistors. This can reduce the power dissipation of timing circuits. For very long timing circuits, using

high value resistors can reduce the size and cost of large value capacitors for the same R-C time constant.

Direct Sensor Interfacing. The wide input voltage range and high impedance of the LMC7211 may make it

possible to directly interface to a sensor without the use of amplifiers or bias circuits. In circuits with sensors

which can produce outputs in the tens to hundreds of millivolts, the LMC7211 can compare the sensor signal

with an appropriately small reference voltage. This may be done close to ground or the positive supply rail. Direct

sensor interfacing may eliminate the need for an amplifier for the sensor signal. Eliminating the amplifier can

save cost, space, and design time.

Low Voltage Operation

Comparators are the common devices by which analog signals interface with digital circuits. The LMC7211 has

been designed to operate at supply voltages of 2.7V without sacrificing performance to meet the demands of 3V

digital systems.

Product Folder Links: LMC7211-N

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

At supply voltages of 2.7V, the common-mode voltage range extends 200 mV (guaranteed) below the negative

supply. This feature, in addition to the comparator being able to sense signals near the positive rail, is extremely

useful in low voltage applications.

Figure 3. Even at Low-Supply Voltage of 2.7V, an Input Signal which Exceeds the Supply Voltages

Produces No Phase Inversion at the Output

At V+= 2.7V propagation delays are tPLH =4μs and tPHL =4μs with overdrives of 100 mV.

Please refer to the performance curves for more extensive characterization.

Shoot-Through Current

The shoot-through current is defined as the current surge, above the quiescent supply current, between the

positive and negative supplies of a device. The current surge occurs when the output of the device switches

states. The shoot-through current results in glitches in the supply voltages. Usually, glitches in the supply lines

are prevented by bypass capacitors. When the glitches are minimal, the value of the bypass capacitors can be

reduced.

Figure 4. Circuit for Measurement of the

Shoot-Through Current

Product Folder Links: LMC7211-N

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

Figure 5. Measurement of the Shoot-Through Current

From Figure 5, the shoot-through current for the LMC7211 can be calculated to be 0.2 mA (typical), and the

duration is 1 μs. The values needed for the bypass capacitors can be calculated as follows:

Area of Δ= ½ (1 μs × 200 μA)

= 100 pC

The capacitor needs to supply 100 picocolumb. To avoid large shifts in the comparator threshold due to changes

in the voltage level, the voltage drop at the bypass capacitor should be limited to 100 mV or less.

The charge needed (100 picocolumb) and the allowable voltage drop (100 mV) will give us the minimum

capacitor value required.

ΔQ=C(ΔV)

C = ΔQ/ΔV = 100 picocolumb/100 mV

C = 10-10/10-1 = 10-9 = 1 nF = 0.001 μF

10-9 = 1 nF = 0.001 μF

The voltage drop of ∼100 mV will cause a threshold shift in the comparator. This threshold shift will be reduced

by the power supply rejection ratio, (PSRR). The PSRR which is applicable here is not the DC value of PSRR

(∼80 dB), but a transient PSRR which will be usually about 20 dB–40 dB, depending on the circuit and the speed

of the transient. This will result in an effective threshold shift of about 1 mV to 10 mV.

For precision and level sensing circuits, it is generally a good goal to reduce the voltage delta on the power

supply to a value equal to or less than the hysteresis of the comparator circuit. If the above circuit was to be used

with 50 mV of hysteresis, it would be reasonable to increase the bypass capacitor to 0.01 μF to reduce the

voltage delta to 10 mV. Larger values may be useful for obtaining more accurate and consistent switching.

Note that the switching current of the comparator can spread to other parts of the board as noise. The bypass

capacitor reduces this noise. For low noise systems this may be reason to make the capacitor larger.

For non-precision circuits, such as using a comparator to determine if a push-button switch is on or off, it is often

cheaper and easier to use a larger value of hysteresis and a small value or bypass capacitance. The low shoot-

through current of the LMC7211 can allow the use of smaller and less expensive bypass capacitors in non-critical

circuits.

Product Folder Links: LMC7211-N

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

Output Short Circuit Current

The LMC7211 has short circuit protection of 40 mA. However, it is not designed to withstand continuous short

circuits, transient voltage or current spikes, or shorts to any voltage beyond the supplies. A resistor in series with

the output should reduce the effect of shorts. For outputs which send signals off PC boards additional protection

devices, such as diodes to the supply rails, and varistors may be used.

Hysteresis

If the input signal is very slow or very noisy, the comparator output might trip several times as the input signal

passes through the threshold. Using positive feedback to add hysteresis to the switching can reduce or eliminate

this problem. The positive feedback can be added by a high value resistor (RF). This will result in two switching

thresholds, one for increasing signals and one for decreasing signals. A capacitor can be added across RFto

increase the switching speed and provide more short term hysteresis. This can result in greater noise immunity

for the circuit.

See Figure 6,Figure 7 and Figure 8.

Note that very heavy loading of the comparator output, such as LED drive or bipolar logic gates, will change the

output voltage and shift the voltage thresholds.

RF≫R1and

RF≫R2

Figure 6. Positive Feedback for Hysteresis

Figure 7. Without Positive Feedback (No Hysteresis)

Product Folder Links: LMC7211-N

LMC7211-N

www.ti.com

SNOS746F –MAY 2004–REVISED JANUARY 2013

Figure 8. With Positive Feedback (Hysteresis or Memory)

Input Protection

If input signals are like to exceed the common mode range of the LMC7211, or it is likely that signals may be

present when power is off, damage to the LMC7211 may occur. Large value (100 kΩto MΩ) input resistors may

reduce the likelihood of damage by limiting the input currents. Since the LMC7211 has very low input leakage

currents, the effect on accuracy will be small. Additional protection may require the use of diodes, as shown in

Figure 9. Note that diode leakage current may affect accuracy during normal operation. The R-C time constant of

RIN and the diode capacitance may also slow response time.

Figure 9.

Layout Considerations

The LMC7211 is not an especially fast comparator, so high speed design practices are not required. The

LMC7211 is capable of operating with very high impedance inputs, so precautions should be taken to reduce

noise pickup with high impedance (∼100 kΩand greater) designs and in electrically noisy environments.

Keeping high value resistors close to the LMC7211 and minimizing the size of the input nodes is a good practice.

With multilayer designs, try to avoid long loops which could act as inductors (coils). Sensors which are not close

to the comparator may need twisted pair or shielded connections to reduce noise.

Open Drain Output, Dual Versions

The LMC7221 is a comparator similar to the LMC7211, but with an open drain output which allows the output

voltage to be different (higher or lower) than the supply voltage. The open drain output is like the open collector

output of a logic gate. This makes the LMC7221 very useful for mixed voltage systems. Many systems will have

different voltages for the analog and microprocessor sections. Please see the LMC7221 datasheet for details.

The performance of the LMC7211 is available in dual devices. Please see the LMC6762 datasheet for details on

a dual push-pull output device. For a dual device with open drain outputs, please see the LMC6772 datasheet.

Rail-to-Rail Input Low Power Comparators—

Product Folder Links: LMC7211-N

LMC7211-N

SNOS746F –MAY 2004–REVISED JANUARY 2013

www.ti.com

Push-Pull Output

LMC7211 SOT23-5, SO-8 Single

LMC6762 SO-8, Dual

Open Drain Output

LMC7221 SOT23-5, SO-8 Single

LMC6772 SO-8, DIP Dual

Additional SOT23-5 Tiny Devices

National Semiconductor has additional parts available in the space saving SOT23 Tiny package, including

amplifiers, voltage references, and voltage regulators. These devices include—

LMC7101 1 MHz gain-bandwidth rail-to-rail input and output amplifier—high input impedance and high gain 700

μA typical current 2.7V, 3V, 5V and 15V specifications.

LMC7111 Low power 50 kHz gain-bandwidth rail-to-rail input and output amplifier with 25 μA typical current

specified at 2.7V, 3.0V, 3.3V, 5V and 10V.

LM7131 Tiny Video amp with 70 MHz gain bandwidth 3V, 5V and ±5V specifications.

LP2980 Micropower SOT 50 mA Ultra Low-Dropout Regulator.

LM4040 Precision micropower shunt voltage reference. Fixed voltages of 2.500V, 4.096V, 5.000V, 8.192V and

10.000V.

LM4041 Precision micropower shut voltage reference 1.225V and adjustable.

LM385 Low current voltage reference. Fixed Voltages of 1.2V and 2.5V.

Contact your National Semiconductor representative for the latest information.

Spice Macromodel

A Spice Macromodel is available for the LMC7211 comparator on the National Semiconductor Amplifier

Macromodel disk. Contact your National Semiconductor representative to obtain the latest version.

Product Folder Links: LMC7211-N

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LMC7211AIM NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LMC72

11AIM

LMC7211AIM/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC72

11AIM

LMC7211AIM5 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 85 C00A

LMC7211AIM5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 C00A

LMC7211AIM5X NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 85 C00A

LMC7211AIM5X/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 C00A

LMC7211AIMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC72

11AIM

LMC7211BIM NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LMC72

11BIM

LMC7211BIM/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC72

11BIM

LMC7211BIM5 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 85 C00B

LMC7211BIM5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 C00B

LMC7211BIM5X NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 85 C00B

LMC7211BIM5X/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 C00B

LMC7211BIMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC72

11BIM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Addendum-Page 2

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LMC7211AIM5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211AIM5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211AIM5X SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211AIM5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211AIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LMC7211BIM5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211BIM5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211BIM5X SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211BIM5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7211BIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 20-Dec-2016

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LMC7211AIM5 SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7211AIM5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7211AIM5X SOT-23 DBV 5 3000 210.0 185.0 35.0

LMC7211AIM5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0

LMC7211AIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LMC7211BIM5 SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7211BIM5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7211BIM5X SOT-23 DBV 5 3000 210.0 185.0 35.0

LMC7211BIM5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0

LMC7211BIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 20-Dec-2016

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

TYP

0.22

0.08

0.25

3.0

2.6

2X 0.95

1.9

1.45 MAX

TYP

0.15

0.00

5X 0.5

0.3

TYP

0.6

0.3

TYP

1.9

3.05

2.75

1.75

1.45

(1.1)

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/C 04/2017

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. Refernce JEDEC MO-178.

0.2 C A B

INDEX AREA

PIN 1

GAGE PLANE

SEATING PLANE

0.1 C

SCALE 4.000

www.ti.com

EXAMPLE BOARD LAYOUT

0.07 MAX

ARROUND 0.07 MIN

ARROUND

5X (1.1)

5X (0.6)

(2.6)

(1.9)

2X (0.95)

(R0.05) TYP

4214839/C 04/2017

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

NOTES: (continued)

4. Publication IPC-7351 may have alternate designs.

5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

SYMM

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:15X

PKG

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

DEFINED

EXPOSED METAL

METAL

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK DETAILS

EXPOSED METAL

www.ti.com

EXAMPLE STENCIL DESIGN

(2.6)

(1.9)

2X(0.95)

5X (1.1)

5X (0.6)

(R0.05) TYP

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/C 04/2017

NOTES: (continued)

6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

7. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE:15X

SYMM

PKG

www.ti.com

PACKAGE OUTLINE

TYP

0.22

0.08

0.25

3.0

2.6

2X 0.95

1.9

1.45 MAX

TYP

0.15

0.00

5X 0.5

0.3

TYP

0.6

0.3

TYP

1.9

3.05

2.75

1.75

1.45

(1.1)

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/C 04/2017

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. Refernce JEDEC MO-178.

0.2 C A B

INDEX AREA

PIN 1

GAGE PLANE

SEATING PLANE

0.1 C

SCALE 4.000

www.ti.com

EXAMPLE BOARD LAYOUT

0.07 MAX

ARROUND 0.07 MIN

ARROUND

5X (1.1)

5X (0.6)

(2.6)

(1.9)

2X (0.95)

(R0.05) TYP

4214839/C 04/2017

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

NOTES: (continued)

4. Publication IPC-7351 may have alternate designs.

5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

SYMM

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:15X

PKG

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

DEFINED

EXPOSED METAL

METAL

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK DETAILS

EXPOSED METAL

www.ti.com

EXAMPLE STENCIL DESIGN

(2.6)

(1.9)

2X(0.95)

5X (1.1)

5X (0.6)

(R0.05) TYP

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/C 04/2017

NOTES: (continued)

6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

7. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE:15X

SYMM

PKG

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LMC7211AIM LMC7211AIM/NOPB LMC7211AIM5 LMC7211AIM5/NOPB LMC7211AIM5X LMC7211AIM5X/NOPB

LMC7211AIMX/NOPB LMC7211BIM LMC7211BIM/NOPB LMC7211BIM5 LMC7211BIM5/NOPB LMC7211BIM5X

LMC7211BIM5X/NOPB LMC7211BIMX LMC7211BIMX/NOPB