BM70/71 Bluetooth(R) Low Energy (BLE) Module Features * Qualified for Bluetooth SIG v4.2 specifications * Certified to FCC, ISED, MIC, KCC, NCC, and SRRC radio regulations * Certified by European RED Assessed Radio module * Compliant to RoHS * Supports UART interface * Supports transparent UART data service of BLE * BM70 module supports 3-channel pulse-width modulation (PWM) and BM71 module supports 1-channel PWM * Supports Precision Temperature Sensor (PTS) for ambient temperature detection * Supports 12-bit ADC (ENOB=10 or 8 bits) for battery and voltage detection * Provides 8-channel ADC for BM70 module and 5channel ADC for BM71 module * Features 18 general purpose I/O (GPIO) pins for the BM70 module and 9 GPIO pins for the BM71 module * Features integrated 32 MHZ crystal * Small and compact surface mount module * Castellated surface mount pads for easy and reliable host PCB mounting FIGURE 1: BM70 MODULE FIGURE 2: BM71 MODULE RF Features * * * * * ISM band 2.402 GHz to 2.480 GHz operation Channels: 0 to 39 Receive Sensitivity: typical -90 dBm (LE) Transmit Power: 0 dBm (typical) Received Signal Strength Indication (RSSI) monitor with 1 dB resolution MAC/Baseband/Higher Layer Features * Secure AES128 encryption * Bluetooth 4.2: GAP, GATT, SMP, L2CAP and integrated public profile * To create custom GATT services, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for details. * I/O capability for Bluetooth 4.0/4.2 authentication * Configurable role as peripheral/central, client/ server 2015-2018 Microchip Technology Inc. Antenna * Integrated chip antenna (BM7xBLES1FC2) - Refer to 4.0 "Antenna", Table 4-1, and Table 4-2 for antenna performance specifications * External antenna connection through RF pad (BM7xBLE01FC2) Power Management * Two low-power modes supported, with wake-up through GPIO or internal timer * Average current: Tx=3.3 mA and Rx=3.2 mA with buck at 3.0V VBAT input and 18.75 ms connection interval, when transmitting full data packets to achieve a data rate of approximately 8.6 kbps DS60001372G-Page 1 BM70/71 Operating Conditions * Operating voltage range: 1.9V to 3.6V * Operating temperature: -40C to +85C Applications * * * * * * * Internet of Things (IoT) Secure Payment Wearable Devices Home and Security Health and Fitness Beacons Industrial and Data Logger General Description The BM70/71 module offers BLE solutions for embedded applications. It conforms to the Bluetooth v4.2 specifications to enhance the throughput and security for the IoT applications. It also supports beacon technology to enhance the user experience for the IoT applications and enables users to control the cloud and receive data without opening the application through a smartphone. The BM70/71 module has an integrated Bluetooth stack and is available in different form factors to optimize space, cost, and RF performance. The poweroptimized design minimizes the current consumption and extends battery life for portable and wearable applications. DS60001372G-Page 2 2015-2018 Microchip Technology Inc. BM70/71 Table of Contents 1.0 Device Overview .............................................................................................................................................................................. 5 2.0 Application Information .................................................................................................................................................................. 13 3.0 Module Configuration ..................................................................................................................................................................... 25 4.0 Antenna.......................................................................................................................................................................................... 27 5.0 Electrical Characteristics................................................................................................................................................................ 37 6.0 Physical Dimensions ...................................................................................................................................................................... 43 7.0 Soldering Recommendations ......................................................................................................................................................... 51 8.0 Ordering Guide .............................................................................................................................................................................. 53 Appendix A: Certification Notices......................................................................................................................................................... 55 Appendix B: Revision History............................................................................................................................................................... 61 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. 2015-2018 Microchip Technology Inc. DS60001372G-Page 3 BM70/71 NOTES: DS60001372G-Page 4 2015-2018 Microchip Technology Inc. BM70/71 1.0 DEVICE OVERVIEW The BM70/71 module is built around Microchip Technology IS1870/71 BLE Integrated Circuit (IC). The IS1870/71 IC includes an on board Bluetooth stack, a power management subsystem, a 2.4 GHz transceiver, and an RF power amplifier. The user can embed Bluetooth functionality into any product using the BM70/71 module. The BM70/71 module enables the following features: * * * * Simple integration and programming Reduced development time Superior wireless module with a low-cost system Interoperability with Apple(R) iOS and AndroidTM OS * A wide range of applications FIGURE 1-1: The BM70/71 module can independently maintain a low power wireless connection. Low power and flexible power management features maximize the lifetime of the BM70/71 module in battery-operated devices. A wide operating temperature range enables its applications in indoor and outdoor environments. The BM70/71 module is a small, compact, and surface-mounted module with castellated pads for easy and reliable host PCB mounting. The relatively small form factor of the module is targeted for applications, such as wearable sports, fitness devices and so on. 1.1 Interface Description Figure 1-1 and Figure 1-2 illustrate an example of the BM70/71 module-based system. BM70 MODULE BLOCK DIAGRAM Note 1: SPI and I2C peripherals of the IS1870/71 IC can be enabled on the BM70/71 module by changing the default firmware. For more details, contact a local Microchip representative. 2015-2018 Microchip Technology Inc. DS60001372G-Page 5 BM70/71 FIGURE 1-2: BM71 MODULE BLOCK DIAGRAM Note 1: SPI and I2C peripherals of the IS1870/71 IC can be enabled on the BM70/71 module by changing the default firmware. For more details, contact a local Microchip representative. DS60001372G-Page 6 2015-2018 Microchip Technology Inc. BM70/71 Figure 1-3 through Figure 1-6 illustrate the pin diagrams of the BM70/71 module. FIGURE 1-3: BM70BLE01FC2 PIN DIAGRAM FIGURE 1-4: BM70BLES1FC2 PIN DIAGRAM 2015-2018 Microchip Technology Inc. DS60001372G-Page 7 BM70/71 FIGURE 1-5: BM71BLE01FC2 PIN DIAGRAM FIGURE 1-6: BM71BLES1FC2 PIN DIAGRAM DS60001372G-Page 8 2015-2018 Microchip Technology Inc. BM70/71 Table 1-1 provides pin descriptions of the BM70/71 module. TABLE 1-1: BM70/71 PIN DESCRIPTION BM70BLE0 BM70BLE BM71BLE BM71BLE Pin Name 1FC2 S1FC2 01FC2 S1FC2 -- 1 -- Type Description -- GND Power Ground reference -- 2 -- -- GND Power Ground reference 1 3 12 13 GND Power Ground reference 2 4 11 14 VBAT Power Battery input. Voltage range: 1.9V to 3.6V -- -- 10 -- BK_IN Power Buck input. Voltage range: 1.9V to 3.6V 3 5 -- -- P2_2 DIO 4 6 -- -- VDD_IO Power I/O positive supply. Do not connect. Ensure VDD_IO and MCU I/O voltage are compatible 5 7 -- -- VDD_IO Power I/O positive supply. Do not connect. Ensure VDD_IO and MCU I/O voltage are compatible 6 8 -- -- ULPC_O Power 1.2V programmable ULPC LDO output for AON-logic and retention memory supply. Internal use only, do not connect to other devices GPIO, default pull-high input PWM1 7 9 -- -- P2_3 DI 8 10 -- -- BK_O Power -- -- 13 6 P1_6 DIO P1_6 -- -- 14 5 P1_7 DIO P1_7 9 11 15 15 P2_7/TX_ IND DIO AI DO GPIO: P2_7 ADC Input: AD14 TX_IND 10 12 -- -- P1_1 DIO AI GPIO: P1_1 ADC Input: AD9 11 13 2 3 P1_2 DIO AI GPIO, default pull-high input AD10 12 14 3 4 P1_3 DIO AI GPIO, default pull-high input AD11 13 15 8 11 P0_0 DIO AI DI GPIO, default pull-high input AD0 UART flow-control CTS 14 16 -- -- P1_0 DIO AI GPIO, default pull-high input AD8 15 17 6 9 P3_6 DIO DO DO GPIO, default pull-high input PWM0 UART flow-control RTS 16 18 16 16 P2_0 DI 17 19 -- -- P2_4 DIO 18 20 -- -- NC -- Legend: A = Analog 2015-2018 Microchip Technology Inc. D = Digital GPIO, default pull-high input PWM2 1.55V buck output. Internal use only, do not connect to other devices System configuration, default pull-high input H: Application mode L: Test mode GPIO, default pull-high input No connection I = Input O = Output DS60001372G-Page 9 BM70/71 TABLE 1-1: BM70/71 PIN DESCRIPTION (CONTINUED) BM70BLE0 BM70BLE BM71BLE BM71BLE 1FC2 Pin Name S1FC2 01FC2 S1FC2 (Continued) 19 21 7 10 RST_N 20 22 5 7 21 23 4 8 22 24 -- 23 25 24 26 25 26 Type Description DI Module Reset (active-low) (internal pull up) HCI_RXD DI HCI UART data input HCI_TXD DO HCI UART data output -- P3_1 DIO GPIO: P3_1 -- -- P3_2 DIO GPIO: P3_2 -- -- P3_3 DIO GPIO: P3_3 27 -- -- P3_4 DIO GPIO: P3_4 28 -- -- P3_5 DIO DO GPIO, default pull-high input LED1 27 29 -- -- P0_7 DIO AI GPIO, default pull-high input AD7 28 30 9 12 P0_2/LED DIO AI P02 AD2 29 31 17 2 GND Power Ground reference -- 32 -- -- GND Power Ground reference 30 -- 1 -- BT_RF AI -- 33 -- -- GND Power Legend: A = Analog DS60001372G-Page 10 D = Digital External antenna connection (50 Ohm) Only for BM70BLE01FC2 and BM71BLE01FC2 No connection for BM71BLES1FC2 Ground reference I = Input O = Output 2015-2018 Microchip Technology Inc. BM70/71 Table 1-2 provides the hardware features of the BM70/71 module. Note: I2C and SPI are accessible using specific firmware versions that support these peripheral interfaces. Please refer to the BM70/71 product page on the Microchip web site for the latest firmware. TABLE 1-2: BM70/71 MODULE HARDWARE FEATURES Feature/ Modules BM70BLES1FC2 BM70BLE01FC2 BM71BLES1FC2 BM71BLE01FC2 Module H/W Default IS1870 Firmware Module H/W Default IS1870 Firmware Module H/W Default IS1871 Firmware Module H/W Default IS1871 Firmware UART 1 1 1 1 1 1 1 1 GPIO (see Note 2) 18 13 18 13 9 4 9 4 12-bit ADC channels 8 6 8 6 5 3 5 3 PWM 3 2 3 2 1 0 1 0 Total pins 33 -- 30 -- 16 -- 17 -- On board antenna with CAN Yes -- -- -- Yes -- -- -- -- -- Yes -- -- -- Yes -- Yes -- -- -- Yes -- -- -- 12x22x2.4 -- 12x15x1.6 -- 9x11.5x2.1 -- 6x8x1.6 -- Configuration No Antenna Government regulatory RF certified Size (mm) Note 1: 2: The GPIO, ADC and PWM numbers used are based on disabling the LED indication and UART Hardware flow-control (RTS/CTS) functionality, see Table 1-1. For a detailed explanation of GPIO, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542). 2015-2018 Microchip Technology Inc. DS60001372G-Page 11 BM70/71 Table 1-3 provides the details of the test pads used for the production test on the bottom of the BM70/71 module. See Figure 1-3 through Figure 1-6 for more details. TABLE 1-3: TEST PADS DETAILS BM70BLE 01FC2 BM70BLE S1FC2 BM71BLE 01FC2 BM71BLE S1FC2 Pin Name Type TP-1 TP-1 TP-3 TP-3 VCC_PA Power 1.55V RF PA LDO TP-2 TP-2 TP-1 TP-1 CLDO_O Power 1.2V CLDO output TP-3 TP-3 TP-2 TP-2 VCC_RF Power 1.28V RF LDO output -- -- TP-4 TP-4 ULPC_O Power 1.2V ULPC LDO output -- -- TP-5 TP-5 BK_O Power 1.55V buck output DS60001372G-Page 12 Description 2015-2018 Microchip Technology Inc. BM70/71 2.0 APPLICATION INFORMATION 2.1 Reference Schematics Figure 2-1 through Figure 2-8 illustrate the BM70/71 module reference schematics for the various Stock Keeping Units (SKUs). The GPIOs are configurable, and the connection depends on the user's application circuit. It is recommended to use an external Reset IC in all applications. An example of using this circuit with the MCP111-195 is illustrated in Figure 2-1, Figure 2-3, Figure 2-5, and Figure 2-7. This Reset IC prevents the Flash data corruption, when VBAT drops below 1.9V (this includes brown-out, power-down, and power-up conditions). FIGURE 2-1: The RF antenna impedance matching circuit in Figure 2-3 and Figure 2-5 require users to implement by the selected antenna specification. For battery-powered applications, it is recommended to use the following external circuits as illustrated in Figure 2-2, Figure 2-4, Figure 2-6, and Figure 2-8. The first circuit (left side) ensures that the LED indicator is bright enough in applications with VBAT > 3.0V. The second circuit (right side) provides protection from battery voltage reverse connection. If a fixed voltage source is applied to VBAT (e.g. 3.3V), the soft start output is necessary to prevent the inrush voltage over 3.6V to damage the Flash. BM70BLES1FC2 REFERENCE CIRCUIT 2015-2018 Microchip Technology Inc. DS60001372G-Page 13 BM70/71 FIGURE 2-2: BM70BLES1FC2 REFERENCE CIRCUIT FIGURE 2-3: BM70BLE01FC2 REFERENCE CIRCUIT DS60001372G-Page 14 2015-2018 Microchip Technology Inc. BM70/71 FIGURE 2-4: BM70BLE01FC2 REFERENCE CIRCUIT FIGURE 2-5: BM71BLE01FC2 REFERENCE CIRCUIT Note 1: Place the capacitor C3 as close as possible to the module. Connect the BK_IN and VBAT trace at C3. 2: The antenna matching component value depends on the user's antenna and PCB layout. 2015-2018 Microchip Technology Inc. DS60001372G-Page 15 BM70/71 FIGURE 2-6: BM71BLE01FC2 REFERENCE CIRCUIT FIGURE 2-7: BM71BLES1FC2 REFERENCE CIRCUIT Note 1: Place the capacitor C3 as close as possible to the module. DS60001372G-Page 16 2015-2018 Microchip Technology Inc. BM70/71 FIGURE 2-8: BM71BLES1FC2 REFERENCE CIRCUIT - OPTIONAL 2015-2018 Microchip Technology Inc. DS60001372G-Page 17 BM70/71 2.2 External Configuration and Programming Configuration and programming modes can be configured using the P2_0 pin. Refer to 3.4 "System Configuration" for details. The BM70/71 module can be configured and programmed using an external configuration and programming tool. Figure 2-9 illustrates the minimum signals required for configuring and programming the module using host PCB. FIGURE 2-9: DS60001372G-Page 18 EXTERNAL CONFIGURATION AND PROGRAMMING 2015-2018 Microchip Technology Inc. BM70/71 2.3 2.3.1 Host MCU Interface HOST MCU INTERFACE OVER UART Figure 2-10 and Figure 2-11 illustrate the interfacing between the BM70/71 and host MCU using UART. UART uses Host Control Interface (HCI) to share the FIGURE 2-10: communication among the Host MCU and BM70/71 module. The interface also illustrates the power scheme using a 3.3V Low Drop Out (LDO) regulator that supply 3.3V to the BM70/71 (BAT_IN) and MCU VDD. This power scheme ensures that the BM70/71 module and MCU I/O voltages are compatible. BM70 MODULE TO MCU INTERFACE Note 1: Ensure that VBAT(=I/O Voltage) and MCU VDD voltages are compatible. 2: Control and indication ports are configurable. 2015-2018 Microchip Technology Inc. DS60001372G-Page 19 BM70/71 FIGURE 2-11: BM71 MODULE TO MCU INTERFACE Note 1: Ensure that VBAT(=I/O Voltage) and MCU VDD voltages are compatible. 2: Control and indication ports are configurable. 3: 10 F (X5R) and 330 Ohm resistor are required for the BM71 module. 4: BK_IN connect to VBAT for BM71BLE01FC2. DS60001372G-Page 20 2015-2018 Microchip Technology Inc. BM70/71 2.3.2 UART READY AFTER EXTERNAL RESET In MCU applications, the time between Reset and the BM70/71 module UART port ready for Test mode and Application mode, after an external Reset (RST_N) FIGURE 2-12: must be notified. Figure 2-12 illustrates the timing diagram of the BM70/71 module UART port ready for Test mode and Application mode after Reset. TIMING DIAGRAM OF BM70/71 MODULE UART READY FOR TEST MODE AFTER RESET 2015-2018 Microchip Technology Inc. DS60001372G-Page 21 BM70/71 2.3.3 UART READY AFTER POWER-ON RESET Figure 2-13 illustrates the timing diagram of the BM70 module UART port ready for Test mode and Application mode after Power-on Reset (POR). cated by the status pins, or by a status report UART command. This status pin or status report UART command is sent to inform the MCU that the BM70/71 module is ready for communication. In Application mode, when the BM70/71 module is ready to communicate with the host MCU after reset, the BM70/71 module may have internal status indi- FIGURE 2-13: DS60001372G-Page 22 TIMING DIAGRAM OF BM70 MODULE UART READY FOR TEST MODE AFTER POWER-ON 2015-2018 Microchip Technology Inc. BM70/71 2.4 Typical Hosted Configuration Figure 2-14 illustrates the typical hosted configuration for the BM71 module. It also illustrates an application using a coin cell battery at VBAT input. For the BM71 FIGURE 2-14: module, a 10 F capacitor (X5R/X7R) is applied to the BAT_IN pin. Only on the BM71 module, the BK_IN pin of the module must be connected to the BAT_IN pin. BM71 MODULE TYPICAL HOSTED CONFIGURATION Note 1: Hardware functions can include ADC and PWM. Refer to "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for a full description of all possible configurable behavior and hardware. 2015-2018 Microchip Technology Inc. DS60001372G-Page 23 BM70/71 2.5 Power-Drop Protection To prevent the BM70/71 module from disruptions, when the voltage drops to less than 1.9V, an "Open Drain" Reset chip with a delay time of 10 ms that triggers Reset at 1.8V output voltage is recommended. Figure 2-15 illustrates the Reset circuit block diagram. FIGURE 2-15: DS60001372G-Page 24 RESET CIRCUIT BLOCK DIAGRAM 2015-2018 Microchip Technology Inc. BM70/71 MODULE CONFIGURATION urable, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for the full description. The BM70/71 module features and services can be configured to fit a wide range of application requirements. Refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for details of all device behavior along with information on how to configure the IS8170/71 IC on the BM70/71 module. Refer to 3.1"UART Interface" through 3.4"System Configuration" that describe default behavior of the BM70/71 module, which can be easily changed. The BM70/71 module I/O pins are configurable as either control or indication signal. The control signals are input to the BM70/71 module and the indication signals are output from the BM70/71 module. Table 3-1 and Table 3-2 provide default pin functions of the default firmware logic in the IS1870/71 IC on the BM70/71 module. For different BM70/71 module application requirements, the I/O pin assignment is configurable and can fit a wide range of application requirements. For additional information related to I/O pin assignment, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542). UART Interface The BM70/71 module UART pins, TXD and RXD, are connected to the UART pins of the host MCU. By default, the UART characteristics are set to a baud rate of 115200, with 8-bit data, 1 stop bit, no parity, and no hardware flow control. These characteristics are config- If hardware function is enabled, LED0 is fixed to this pin If hardware function is enabled, TX_IND is fixed to this pin If hardware function is enabled, UART_CTS is fixed to this pin If hardware function is enabled, UART_RTS is fixed to this pin PAIRING_KEY(1) UART_RX_IND(1) LINK_DROP(1) RSSI_IND(1) CONFIGURATION AND INDICATION I/O ASSIGNMENTS FOR BM70 MODULE LOW_BATTERY_IND(1) N/C(1) PINS TABLE 3-1: Control and Indication I/O Pins STATUS1_IND(1) 3.1 3.2 RF_ACTIVE_IND(1) 3.0 P1_0 P3_1 Default P3_2 Default P3_3 Default P3_4 Default P0_7 Default P1_1 Default P2_2 Default P2_4 Default P3_5 Default P3_6 P0_0 P2_7 P0_2 Default Default Default Default Note 1: These signals are part of the remappable hardware functionality and can be input/output on different GPIO pins of the module. Refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for details. 2015-2018 Microchip Technology Inc. DS60001372G-Page 25 BM70/71 P1_6 Default P1_7 Default P1_2 Default P1_3 Default P3_6 Default P0_0 Default P2_7 Default P0_2 3.3 Default Reset (RST_N) The Reset input pin (RST_N) is used to reset the BM70/71 module with an active-low pulse with a minimum pulse width of 63 ns. TABLE 3-3: 3.4 System Configuration Table 3-3 provides the system configuration settings of the P2_0 pin that places the BM70/71 module into various operational modes. The P2_0 pin has an internal pull up. SYSTEM CONFIGURATION SETTINGS P2_0 Note: If hardware function is enabled, LED0 is fixed to this pin If hardware function is enabled, TX_IND is fixed to this pin If hardware function is enabled, UART_CTS is fixed to this pin If hardware function is enabled, UART_RTS is fixed to this pin STATUS2_IND STATUS1_IND RF_ACTIVE_IND PAIRING_KEY UART_RX_IND LINK_DROP CONFIGURATION AND INDICATION I/O ASSIGNMENTS FOR BM71 MODULE RSSI_IND LOW_BATTERY_IND PINS TABLE 3-2: Operational Mode High Application mode Low Test mode (calibration of the IS1870/71 IC), Configuration mode (programming of configuration parameters for default firmware), Firmware Update mode (programming of internal flash memory of IS1870/71 IC). For more details and information on the use of these different modes, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542). DS60001372G-Page 26 2015-2018 Microchip Technology Inc. BM70/71 4.0 ANTENNA 4.1 Antenna Characteristics 4.1.1 BM70BLES1FC2 CERAMIC CHIP ANTENNA The BM70BLES1FC2 module contains an inbuilt ceramic chip antenna. Figure 4-1 illustrates the antenna radiation pattern of the ceramic chip antenna on the BM70BLES1FC2 module. FIGURE 4-1: BM70BLES1FC2 ANTENNA RADIATION PATTERN Table 4-1 provides the antenna radiation pattern details of the BM70BLES1FC2 module. TABLE 4-1: Parameter BM70BLES1FC2 ANTENNA RADIATION PATTERN DETAILS Values Frequency 2450 MHz Peak Gain 1.63 dBi Efficiency 71.55% 2015-2018 Microchip Technology Inc. DS60001372G-Page 27 BM70/71 4.1.2 BM71BLES1FC2 CERAMIC CHIP ANTENNA The BM71BLES1FC2 module contains an inbuilt ceramic chip antenna. Figure 4-2 illustrates the antenna radiation pattern of the ceramic chip antenna on the BM71BLES1FC2 module. FIGURE 4-2: BM71BLES1FC2 ANTENNA RADIATION PATTERN Table 4-2 provides the antenna radiation pattern details of the BM71BLES1FC2 module. TABLE 4-2: BM71BLES1FC2 ANTENNA RADIATION PATTERN DETAILS Parameter Values Frequency 2442 MHz Peak Gain 0.1 dBi Efficiency 42.7% DS60001372G-Page 28 2015-2018 Microchip Technology Inc. BM70/71 4.2 Antenna Placement For a Bluetooth wireless product, the antenna placement affects the whole system performance. The antenna requires free space to radiate the RF signals and it cannot be surrounded by the ground plane. FIGURE 4-3: Figure 4-3 illustrates a typical example of the good and poor antenna placement of the BM70BLES1FC2 module on the main application board with the ground plane. BM70BLES1FC2 ANTENNA PLACEMENT EXAMPLES 2015-2018 Microchip Technology Inc. DS60001372G-Page 29 BM70/71 Figure 4-4 illustrates a typical example of the good and poor antenna placement of the BM71BLES1FC2 module on the main application board with the ground plane. FIGURE 4-4: DS60001372G-Page 30 BM71BLES1FC2 ANTENNA PLACEMENT EXAMPLES 2015-2018 Microchip Technology Inc. BM70/71 4.3 Antenna Considerations Table 4-3 provides the part number and manufacturer details of the antenna used on the BM70BLES1FC2 module. TABLE 4-3: BM70BLES1FC2 ANTENNA DETAILS Description Part Number Manufacturer ANT ANT3216A063R2400A PIFA 2.4 GHZ L3.2W1.6 ANT3216A063R2400A YAGEO Description Part Number Manufacturer ANT ANT3216LL00R2400A 2.4 GHZ L3.2W1.6 ANT3216LL00R2400A YAGEO Table 4-4 provides the part number and manufacturer details of the antenna used on the BM71BLES1FC2 module. TABLE 4-4: BM71BLES1FC2 ANTENNA DETAILS 2015-2018 Microchip Technology Inc. DS60001372G-Page 31 BM70/71 4.4 4.4.1 Host PCB Mounting Suggestion BM70BLES1FC2 HOST PCB MOUNTING Figure 4-5 illustrates the host PCB mounting suggestions for the BM70BLES1FC2 module, showing the minimum ground plane area to the left and right of the module for best antenna performance. FIGURE 4-5: DS60001372G-Page 32 The area under the antenna must not contain any top, inner or bottom copper layer, while designing the host PCB. A low-impedance ground plane ensures the best radio performance (best range, low noise). The ground plane can be extended beyond the minimum recommended as required for the host PCB EMC noise reduction. For best range performance, keep all external metal away from the ceramic chip antenna by a minimum of 30 mm. BM70BLES1FC2 HOST PCB MOUNTING SUGGESTION 2015-2018 Microchip Technology Inc. BM70/71 4.4.2 BM70BLE01FC2 HOST PCB MOUNTING Figure 4-6 illustrates the mounting suggestions for the BM70BLE01FC2 module and it also shows a connection to UFL connector. A low-impedance ground plane will ensure the best radio performance (best range, low noise). 50 Ohm micro-strip trace. The micro-strip trace can be extended to include passive parts for antenna attenuation padding, impedance matching, or to provide test points. It is recommended that the micro-strip trace be as short as possible for minimum loss and best impedance matching. If the micro-strip trace is longer, it must be a 50 Ohm controlled impedance. The pin 30 (BT_RF) is connected to an external antenna connector, a PCB trace antenna, or a component (ceramic chip) antenna through a host PCB FIGURE 4-6: BM70BLE01FC2 HOST PCB MOUNTING SUGGESTIONS 2015-2018 Microchip Technology Inc. DS60001372G-Page 33 BM70/71 4.4.3 BM71BLES1FC2 HOST PCB MOUNTING Figure 4-7 illustrates the mounting suggestions for the BM71BLES1FC2 module. It also shows the area around the antenna, required for the best antenna performance. FIGURE 4-7: DS60001372G-Page 34 The area under the antenna must not contain any top, inner, or bottom copper layer while designing the host PCB. A low-impedance ground plane ensures the best radio performance (best range, low noise). The ground plane can be extended beyond the minimum recommended as required for the host PCB EMC noise reduction. For best range performance, keep all external metal away from the ceramic chip antenna by a minimum of 30 mm. BM71BLES1FC2 HOST MOUNTING SUGGESTION 2015-2018 Microchip Technology Inc. BM70/71 4.4.4 BM71BLE01FC2 HOST PCB MOUNTING Figure 4-8 illustrates the mounting suggestions for the BM71BLE01FC2 module. It also shows a connection to the UFL connector. A low-impedance ground plane ensures the best radio performance (best range, low noise). FIGURE 4-8: The pin 1 (BT_RF) is connected to an external antenna connector, a PCB trace antenna, or a component (ceramic chip) antenna through a host PCB 50 Ohm micro-strip trace. The micro-strip trace can be extended to include passive parts for antenna attenuation padding, impedance matching, or to provide test points. It is recommended that the micro-strip trace be as short as possible for minimum loss and best impedance matching. If the micro-strip trace is longer, it must be a 50 Ohm controlled impedance. BM71BLE01FC2 HOST PCB MOUNTING SUGGESTION 2015-2018 Microchip Technology Inc. DS60001372G-Page 35 BM70/71 NOTES: DS60001372G-Page 36 2015-2018 Microchip Technology Inc. BM70/71 5.0 ELECTRICAL CHARACTERISTICS This section provides an overview of the BM70/71 module electrical characteristics. Additional information will be provided in future revisions of this document as it becomes available. Absolute Maximum Ratings Ambient temperature under bias for modules parts ending with 0002...................................................... -20C to +70C Ambient temperature under bias for modules parts ending with 0B0x..................................................... .-40C to +85C Storage temperature .............................................................................................................................. -40C to +125C Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +3.6V Voltage of any digital pin ............................................................................................................-0.3V to VDD + 0.3 3.9 Maximum output current sink by any I/O pin..........................................................................................................12 mA Maximum output current sourced by any I/O pin....................................................................................................12 mA Note: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions, above those indicated in the operation listings of this specification, is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2015-2018 Microchip Technology Inc. DS60001372G-Page 37 BM70/71 Table 5-1 provides the recommended operating conditions of the BM70/71 module. TABLE 5-1: RECOMMENDED OPERATING CONDITIONS Symbol Min. Typ. Max. 1.9V 3.0V 3.6V RST_N 1.9V 3.0V 3.6V Other I/O 1.9V -- 3.6V 0.7 VDD -- VDD VSS -- 0.3 VDD 0.8 VDD -- VDD PMU VDD (VBAT, BK_IN, AVDD) GPIO VIH (Input High Voltage) VIL (Input Low Voltage) VOH (Output High Voltage) (High drive, 12 mA) VOL (Output Low Voltage) (High drive, 12 mA) Pull up resistance Pull down resistance VSS -- 0.2 VDD 34 kOhm 48 kOhm 74 kOhm 29 kOhm 47 kOhm 86 kOhm Supply Current (see Note 1) Peak Tx mode current at VDD=3V, Tx=0 dBm, Buck mode -- 10 mA at +25C 13 mA at +70C/+85C Peak Rx mode current at VDD=3V, Buck mode -- 10 mA at +25C 13 mA at +70C/+85C "Reduced current consumption" low power mode current (see Note 2) -- 60 A at +25C "Shutdown" low power mode current (see Note 2) 1.0 A -- 2.9 A Note 1: The current measurements are characterized across a sample of BM70/71 modules at room temperature (+25C), unless otherwise noted. 2: For more details on "Reduced current consumption" or "Shutdown" low power modes, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542). Note: For more details on "Analog to Digital Converter (ADC) and Precision Temperature Sensor (PTS) specifications, refer to "IS1870/71 Bluetooth(R) Low Energy SoC data sheet" (DS60001371). DS60001372G-Page 38 2015-2018 Microchip Technology Inc. BM70/71 Table 5-2 provides the RF specifications of the BM70/71 module. TABLE 5-2: RF SPECIFICATIONS Parameter Min. Typ. Max. 2402 MHz -- 2480 MHz -- 0 dBm -- -25 dBm -- 3 dBm Transmitter Frequency Output Power RF Power Control Range In-band Spurious (N2) -- -38.5 dBm -- In-band Spurious (N3) -- -43.25 dBm -- Modulation Characteristic - Frequency Deviation (see Note 1) -- 247 kHz -- 2480 MHz Receiver Frequency 2402 MHz -- Sensitivity Level (interference active) -- -90 dBm -- Interference Performance Co-channel -- 17 dB -- Adjacent 1 MHz -- 0 dB -- Adjacent 2 MHz -- -25 dB -- Adjacent >= 3 MHz -- -32 dB -- -- -37.5 dBm -- Inter-modulation Characteristic (n=3,4,5) Maximum Usable Level 0 dBm Note 1: Tested by transmitting known `00001111'b patterns. 2015-2018 Microchip Technology Inc. DS60001372G-Page 39 BM70/71 5.1 5.1.1 Current Consumption Details Tx/Rx CURRENT CONSUMPTION DETAILS Figure 5-1 illustrates the Tx/Rx peak current consumption of 12 mA during an advertising event. However, the average current consumption is only around 230 A while advertising at an interval of approximately 100 ms, see Figure 5-2. This is due to the "Reduced Current Consumption" Low Power mode being enabled (configuration parameter UART_RX_IND). Reducing the current draw to approximately 60 A, while not actively transmitting the FIGURE 5-1: DS60001372G-Page 40 advertisings packets, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for more details. The overall average current consumption is measured with a 3.3V VBAT input, and is affected by the way the IS1870/71 IC on the BM70/71 module has been configured to operate. A low average current value can be achieved by choosing the minimum settings for the advertising interval and connection interval, which meet the data throughput requirements of the intended application. The lower or less frequent the interval time periods, the lower the overall average current to be drawn. TX/RX PEAK CURRENT CONSUMPTION OF AN ADVERTISING EVENT 2015-2018 Microchip Technology Inc. BM70/71 Figure 5-2 illustrates the oscilloscope screen, captured when the auto operation and Low Power mode is active on the BM70/71 module. Refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542) for more details on the auto operation. FIGURE 5-2: TX/RX AVERAGE CURRENT CONSUMPTION WHILE BM70/71 MODULE IS ADVERTISING For additional information on the current consumption measurements, test conditions and test environment setup, refer to the "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542).This user guide provides detailed information about the behavior of the default internal logic of the IS1870/71 IC on the BM70/71 module. 2015-2018 Microchip Technology Inc. DS60001372G-Page 41 BM70/71 Table 5-3 provides the average current consumption measurements for the BM70/71 module in Application mode. TABLE 5-3: BM70/71 APPLICATION MODE CURRENT CONSUMPTION MEASUREMENTS Test Mode Advertising (see Note 1,2,3) Connected (see Note 1,2,4) Interval [ms] Average Current Consumption 20 1.061 mA 50 505 A 100 298 A 500 113 A 1000 89 A 18.75 2.23 mA 50 2.13 mA 100 2.10 mA 500 83 A 1000 80 A Note 1: These measurements are done at an operating temperature of +25C at 3.3V and are characterized across a sample of BM70/71 modules. 2: These measurements are taken with version 1.06 firmware, loaded into the module with "Reduced Current Consumption" Low Power mode enabled. For more details on Low Power modes and current consumption configuration, refer to "BM70/71 Bluetooth(R) Low Energy Module User's Guide" (DS50002542). 3: The advertising packet data payload is approximately 15 bytes in length. 4: The amount of data being transmitted between two peer devices can affect the average current measured. The average current measurements are done with only the necessary Bluetooth packets being exchanged to keep the connection active at the stated interval. DS60001372G-Page 42 2015-2018 Microchip Technology Inc. BM70/71 6.0 PHYSICAL DIMENSIONS 6.1 BM70BLES1FC2 Figure 6-1 illustrates the physical dimensions of the BM70BLES1FC2 module. FIGURE 6-1: BM70BLES1FC2 MODULE DIMENSIONS 2015-2018 Microchip Technology Inc. DS60001372G-Page 43 BM70/71 Figure 6-2 illustrates the recommended PCB footprint. Ensure that no top copper layer is near the test pin area. FIGURE 6-2: DS60001372G-Page 44 BM70BLES1FC2 RECOMMENDED PCB FOOTPRINT 2015-2018 Microchip Technology Inc. BM70/71 6.2 BM70BLE01FC2 Figure 6-3 illustrates the physical dimensions of the BM70BLE01FC2 module. FIGURE 6-3: BM70BLE01FC2 MODULE DIMENSIONS 2015-2018 Microchip Technology Inc. DS60001372G-Page 45 BM70/71 Figure 6-4 illustrates the recommended PCB footprint. FIGURE 6-4: DS60001372G-Page 46 BM70BLE01FC2 RECOMMENDED PCB FOOT PRINT 2015-2018 Microchip Technology Inc. 2015-2018 Microchip Technology Inc. 6.3 BM71BLES1FC2 Figure 6-5 illustrates the physical dimensions of the BM71BLES1FC2 module. FIGURE 6-5: BM71BLES1FC2 MODULE DIMENSIONS BM70/71 DS60001372G-Page 47 BM70/71 Figure 6-6 illustrates the recommended PCB footprint. Ensure that no top copper layer is near the test pin area. FIGURE 6-6: DS60001372G-Page 48 BM71BLES1FC2 RECOMMENDED PCB FOOTPRINT 2015-2018 Microchip Technology Inc. 2015-2018 Microchip Technology Inc. 6.4 BM71BLE01FC2 Figure 6-7 illustrates the physical dimensions of the BM71BLE01FC2 module. FIGURE 6-7: BM71BLE01FC2 MODULE DIMENSIONS BM70/71 DS60001372G-Page 49 BM70/71 Figure 6-8 illustrates the recommended PCB footprint. FIGURE 6-8: DS60001372G-Page 50 BM71BLE01FC2 RECOMMENDED PCB FOOTPRINT 2015-2018 Microchip Technology Inc. BM70/71 7.0 SOLDERING RECOMMENDATIONS The BM70/71 module is assembled using a standard lead-free, reflow profile, IPC/JEDEC J-STD-020. The BM70/71 module can be soldered to the host PCB by using the standard lead or lead-free solder reflow profiles. To avoid any damage to the BM70/71 module, follow these recommendations: * Refer to the "AN233 Solder Reflow Recommendation" (DS00233) document for the soldering reflow recommendations * Do not exceed the peak temperature (TP) of +260C * Use no-clean flux solder paste * Do not wash the BM70/71 module as moisture can be trapped under the shield * Use only one flow. If the PCB requires multiple flows, apply the BM70/71 module on the final flow Figure 7-1 illustrates the reflow profile of the BM70/71 module. FIGURE 7-1: REFLOW PROFILE 2015-2018 Microchip Technology Inc. DS60001372G-Page 51 BM70/71 NOTES: DS60001372G-Page 52 2015-2018 Microchip Technology Inc. 2015-2018 Microchip Technology Inc. 8.0 ORDERING GUIDE Table 8-1 provides the ordering information of the BM70/71 module. TABLE 8-1: BM70/71 MODULE ORDERING INFORMATION Operating Temperature Range Firmware Version Antenna Shield Pin # Regulatory Certification Regulatory Model No. (see Note 3) Bluetooth 4.2 BLE module, (12x15x1.6 mm) -20C to +70C V1.03 External No 30 No N/A BM70BLE01FC2-00 02AA BM70 Bluetooth 4.2 BLE module, (12x15x2.4 mm) -20C to +70C V1.03 On board Yes 33 FCC, ISED, CE, MIC, KCC, NCC, SRRC BM70BLES1FC2 BM70BLES1FC2-00 02AA BM71 Bluetooth 4.2 BLE module, (6x8x1.6 mm) -20C to +70C V1.06 External No 17 No N/A BM71BLE01FC2-00 02AA BM71 Bluetooth 4.2 BLE module, (9x11.5x2.1 mm) -20C to +70C V1.06 On board Yes 16 FCC, ISED, CE, MIC, KCC, NCC, SRRC BM71BLES1FC2 BM71BLES1FC2-00 02AA BM70 Bluetooth 4.2 BLE module, (12x15x1.6 mm) -40C to +85C V1.06 External No 30 No N/A BM70BLE01FC2-0B 03AA BM70 Bluetooth 4.2 BLE module, (12x15x2.4 mm) -40C to +85C V1.06 On board Yes 33 FCC, ISED, CE, MIC, KCC, NCC, SRRC BM70BLES1FC2 BM70BLES1FC2-0B 03AA BM71 Bluetooth 4.2 BLE module, (6x8x1.6 mm) -40C to +85C V1.06 External No 17 No N/A BM71BLE01FC2-0B 02AA BM71 Bluetooth 4.2 BLE module, (9x11.5x2.1 mm) -40C to +85C V1.06 On board Yes 16 FCC, ISED, CE, MIC, KCC, NCC, SRRC BM71BLES1FC2 BM71BLES1FC2-0B 02AA Module Description BM70 Orderable Part Number (see Note 1 and 2) 2: The numbers listed under "Orderable Part Number" must be used, when purchasing a specific module from Microchip. 3: "Regulatory Model No." column represents the Model No. listed in Microchip's regulatory notices. The extensions used to order/buy a specific version of the module are listed in the "Orderable Part Number". BM70/71 DS60001372G-page 53 Note 1: With the introduction of the IS187xSF-202 IC, the PC tools provided by Microchip which change/control Bluetooth operation have been revised. The correct tool version must be paired with the applicable module/IC part number. All module parts ending with BM7xBLEX1FC2-0BxxAA must use the PC tools ending with 0BxxAA. All module parts ending with BM7xBLEX1FC2-0002AA must use the PC tools ending with 0002AA. BM70/71 NOTES: DS60001372G-Page 54 2015-2018 Microchip Technology Inc. BM70/71 APPENDIX A: CERTIFICATION NOTICES The BM70 module (BM70BLES1FC2) has received the regulatory approval for the following countries: * BT SIG/QDID:74246 * United States/FCC ID: A8TBM70ABCDEFGH * Canada/ISED - IC ID: 12246A-BM70BLES1F2 - HVIN: BM70BLES1F2 * Europe/CE * Japan/MIC: 202-SMD069 * Korea/KCC: MSIP-CRM-mcp-BM70BLES1FC2 * Taiwan/NCC No: CCAN15LP0500T1 * China/SRRC: CMIIT ID: 2015DJ7135 The BM71 module (BM71BLES1FC2) has received the regulatory approval for the following countries: * BT SIG/QDID:74246 * United States/FCC ID: A8TBM71S2 * Canada/ISED - IC ID: 12246A-BM71S2 - HVIN: BM71BLES1FC2 * Europe/CE * Japan/MIC: 005-101150 * Korea/KCC: MSIP-CRM-mcp-BM71BLES1FC2 * Taiwan/NCC No: CCAN16LP0010T5 * China/SRRC: CMIIT ID: 2016DJ2787 A.0.1 UNITED STATES The BM70/71 module has received Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart C "Intentional Radiators" modular approval in accordance with Part 15.212 Modular Transmitter approval. Modular Transmitter approval allows the end user to integrate the BM70/71 module into a finished product without obtaining subsequent and separate FCC approvals for intentional radiation, provided no changes or modifications are made to the module circuitry. Changes or modifications could void the user's authority to operate the equipment. The end user must comply with all of the instructions provided by the Grantee, which indicate installation and/or operating conditions necessary for compliance. functions on the transmitter module (i.e., Verification, or Declaration of Conformity) as appropriate (e.g., transmitter modules may also contain digital logic functions) A.0.2 LABELING AND USER INFORMATION REQUIREMENTS The BM70/71 module has been labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the finished product into which the module is installed must also display a label referring to the enclosed module. This exterior label should use the following wording: For the BM70 module: Contains Transmitter Module FCC ID: A8TBM70ABCDEFGH or Contains FCC ID: A8TBM70ABCDEFGH This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation For the BM71 module: Contains Transmitter Module FCC ID: A8TBM71S2 or Contains FCC ID: A8TBM71S2 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation The finished product is required to comply with all other applicable FCC equipment authorizations regulations, requirements and equipment functions that are not associated with the transmitter module portion. For example, compliance must be demonstrated: to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15 Subpart B), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for the non-transmitter 2015-2018 Microchip Technology Inc. DS60001372G-Page 55 BM70/71 The user's manual for the finished product should include the following statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna * Increase the separation between the equipment and receiver * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected * Consult the dealer or an experienced radio/TV technician for help Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748, which is available at the FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB) http://apps.fcc.gov/oetcf/kdb/index.cfm. A.0.3 FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB): http://apps.fcc.gov/oetcf/kdb/index.cfm. A.1 Canada The BM70/71 module has been certified for use in Canada under Innovation, Science and Economic Development Canada (ISED, formerly Industry Canada) Radio Standards Procedure (RSP) RSP-100, Radio Standards Specification (RSS) RSS-247 and RSS-Gen. Modular approval permits the installation of a module in a host device without the need to recertify the device. A.1.1 LABELING AND USER INFORMATION REQUIREMENTS Labeling Requirements for the Host Device (from Section 3.1, RSS-Gen, Issue 4, November 2014): The host device shall be properly labeled to identify the module within the host device. The Innovation, Science and Economic Development Canada certification label of a module shall be clearly visible at all times when installed in the host device; otherwise, the host device must be labeled to display the Innovation, Science and Economic Development Canada certification number of the module, preceded by the word "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows: For the BM70 module: Contains IC: 12246A-BM70BLES1F2 For the BM71 module: RF EXPOSURE All transmitters regulated by FCC must comply with RF exposure requirements. KDB 447498 General RF Exposure Guidance provides guidance in determining whether proposed or existing transmitting facilities, operations or devices comply with limits for human exposure to Radio Frequency (RF) fields adopted by the Federal Communications Commission (FCC). Contains IC: 12246A-BM71S2 User Manual Notice for License-Exempt Radio Apparatus (from Section 8.4, RSS-Gen, Issue 4, November 2014): User manuals for license-exempt radio appara- From the FCC Grant: Output power listed is conducted. This grant is valid only when the module is sold to OEM integrators and must be installed by the OEM or OEM integrators. This transmitter is restricted for use with the specific antenna(s) tested in this application for Certification and must not be co-located or operating in conjunction with any other antenna or transmitters within a host device, except in accordance with FCC multi-transmitter product procedures. This module is approved for installation into mobile or/and portable host platforms A.0.4 HELPFUL WEB SITES Federal Communications http://www.fcc.gov DS60001372G-Page 56 Commission (FCC): 2015-2018 Microchip Technology Inc. BM70/71 tus shall contain the following or equivalent notice in a conspicuous location in the user manual or alternatively on the device or both: This device complies with Industry Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Guidelines on Transmitter Antenna for License Exempt Radio Apparatus: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformement a la reglementation d'Industrie Canada, le present emetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inferieur) approuve pour l'emetteur par Industrie Canada. Dans le but de reduire les risques de brouillage radioelectrique a l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnee equivalente (p.i.r.e.) ne depasse pas l'intensite necessaire a l'etablissement d'une communication satisfaisante. Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required impedance for each. A.1.2 RF EXPOSURE All transmitters regulated by the Innovation, Science and Economic Development Canada (ISED) must comply with RF exposure requirements listed in RSS-102 - Radio Frequency (RF) Exposure Compliance of Radio communication Apparatus (All Frequency Bands). 2015-2018 Microchip Technology Inc. This transmitter is restricted for use with a specific antenna tested in this application for certification, and must not be co-located or operating in conjunction with any other antenna or transmitters within a host device, except in accordance with Innovation, Science and Economic Development Canada multi-transmitter guidelines. The installation of the transmitter must ensure that the antenna has a separation distance of at least 6.5 cm from all persons or compliance must be demonstrated according to the ISED SAR procedures. A.1.3 HELPFUL WEB SITES Innovation, Science and Economic Development Canada (ISED): http://www.ic.gc.ca/ A.2 Europe The BM70/71 module is an Radio Equipment Directive (RED) assessed radio module that is CE marked and has been manufactured and tested with the intention of being integrated into a final product. The BM70/71 module has been tested to RED 2004/53/EC Essential Requirements for Health and Safety (Article (3.1(a)), Electromagnetic Compatibility (EMC) (Article 3.1(b)), and Radio (Article 3.2), which is summarized in the following European Compliance Testing table. The ETSI provides guidance on modular devices in the "Guide to the application of harmonised standards covering Article 3.1(b) and Article 3.2 of the Directive 2014/53/EU RED to multi-radio and combined radio and non-radio equipment" document available at http://www.etsi.org/deliver/etsi_eg/203300_203399/20 3367/01.01.01_60/eg_203367v010101p.pdf. Note: A.2.1 To maintain conformance to the testing listed in Table A-1/Table A-2, the module shall be installed in accordance with the installation instructions in this data sheet and shall not be modified. When integrating a radio module into a completed product, the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essential requirements against the RED. LABELING AND USER INFORMATION REQUIREMENTS The label on the final product which contains the BM70/71 module must follow CE marking requirements. The RED Compliance Association Technical Guidance Note 01 provides guidance on final product CE marking. DS60001372G-Page 57 BM70/71 TABLE A-1: EUROPEAN COMPLIANCE TESTING (BM70 MODULE) Certification Standards Article Safety EN60950-1:2006/A11:2009/A 1:2010/A12:2011/A2:2013 [3.1(a)] Health EN300328 V1.9.1/ EN62479:2010 EMC EN301489-1 V1.9.2 [3.1(b)] EN301489-17 V2.2.1 Laboratory TUV Rheinland Taiwan EN301489-1 V2.1.1 EN301489-17 V2.2.0 Report Number Date 10051261 003 2016-01-05 10053580 001 2015-12-10 10051137 002 2016-01-08 10051137 003 2017-05-26 10053580 001 2015-12-10 EN301489-17 V3.1.1 EN301489-17 V3.2.0 Radio EN300328 V1.9.1 (3.2) 50067510 001 EN300328 V2.1.1 (1) 50067510 002 2017-10-04 2017-05-26 Note 1: RF reports apply only to modules using the part IS1870SF-202. TABLE A-2: EUROPEAN COMPLIANCE TESTING (BM71 MODULE) Certification Standards Article Safety EN60950-1:2006/A11:2009/A 1:2010/A12:2011/A2:2013 [3.1(a)] Health EN62479:2010 EMC EN301489-1 V1.9.2 [3.1(b)] EN301489-17 V2.2.1 Laboratory TUV Rheinland Taiwan EN301489-1 V2.1.1 EN301489-1 V2.2.0 Report Number Date 10053210 001 2016-01-07 10053433 001 2015-12-29 10052964 001 2015-10-22 10052964 002 2017-05-26 EN301489-17 V3.1.1 EN301489-17 V3.2.0 Radio EN300328 V1.9.1 (3.2) EN300328 V2.1.1 10053433 001 2015-12-29 50067509 001(1) 2017-04-10 50067509 002 2017-05-26 Note 1: RF reports apply only to modules using the part IS1871SF-202. A.2.2 CONFORMITY ASSESSMENT From ETSI Guidance Note EG 203367, section 6.1 Non-radio products are combined with a radio product: If the manufacturer of the combined equipment installs the radio product in a host non-radio product in equivalent assessment conditions (i.e. host equivalent to the one used for the assessment of the radio product) and according to the installation instructions for the radio product, then no additional assessment of the combined equipment against article 3.2 of the RED is required. The European Compliance Testing listed in Table A-1 and Table A-2 were performed using the integral ceramic chip antenna. DS60001372G-Page 58 A.2.3 SIMPLIFIED EU DECLARATION OF CONFORMITY Hereby, Microchip Technology Inc. declares that the radio equipment type BM70/71 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity, for this product, is available at: http://www.microchip.com/design-centers/wireless-connectivity A.2.4 HELPFUL WEB SITES A document that can be used as a starting point in understanding the use of Short Range Devices (SRD) in Europe is the European Radio Communications Committee (ERC) Recommendation 70-03 E, which can be downloaded from the European Radio Communications Committee (ECC) at: http://www.ero.dk/. 2015-2018 Microchip Technology Inc. BM70/71 Additional helpful web sites are: * Radio Equipment Directive (2014/53/EU): https://ec.europa.eu/growth/single-market/european-standards/harmonised-standards/red_en * European Conference of Postal and Telecommunications Administrations (CEPT): http://www.cept.org * European Telecommunications Standards Institute (ETSI): http://www.etsi.org * The Radio Equipment Directive Compliance Association (REDCA): http://www.redca.eu/ A.3 Japan The BM70/71 module has received type certification and is labeled with its own technical conformity mark and certification number as required to conform to the technical standards regulated by the Ministry of Internal Affairs and Communications (MIC) of Japan pursuant to the Radio Act of Japan. Integration of this module into a final product does not require additional radio certification provided installation instructions are followed and no modifications of the module are allowed. Additional testing may be required: * If the host product is subject to electrical appliance safety (for example, powered from an AC mains), the host product may require Product Safety Electrical Appliance and Material (PSE) testing. The integrator should contact their conformance laboratory to determine if this testing is required * There is an voluntary Electromagnetic Compatibility (EMC) test for the host product administered by VCCI: http://www.vcci.jp/vcci_e/index.html A.3.1 LABELING AND USER INFORMATION REQUIREMENTS For the BM71 module, due to the limited module size, the technical conformity logo and ID displayed in the data sheet only and cannot be displayed on the module label. The final product in which this module is being used must have a label referring to the type certified module inside: A.3.2 HELPFUL WEB SITES Ministry of Internal Affairs and Communications (MIC): http://www.tele.soumu.go.jp/e/index.htm Association of Radio Industries and Businesses (ARIB): http://www.arib.or.jp/english/ A.4 Korea The BM70/71 module has received certification of conformity in accordance with the Radio Waves Act. Integration of this module into a final product does not require additional radio certification provided installation instructions are followed and no modifications of the module are allowed. A.4.1 LABELING AND USER INFORMATION REQUIREMENTS The label on the final product which contains the BM70/71 module must follow KC marking requirements. The integrator of the module should refer to the labeling requirements for Korea available on the Korea Communications Commission (KCC) website. The BM70 module is labeled with its own KC mark. The final product requires the KC mark and certificate number of the module: The label on the final product which contains the BM70/71 module must follow Japan marking requirements. The integrator of the module should refer to the labeling requirements for Japan available at the Ministry of Internal Affairs and Communications (MIC) website. For the BM70 module, due to a limited module size, the technical conformity logo and ID is displayed in the data sheet and/or packaging and cannot be displayed on the module label. The final product in which this module is being used must have a label referring to the type certified module inside: 2015-2018 Microchip Technology Inc. The BM71 module is labeled with its own KC mark. The final product requires the KC mark and certificate number of the module: DS60001372G-Page 59 BM70/71 A.4.2 HELPFUL WEB SITES Korea Communications Commission (KCC): http://www.kcc.go.kr National Radio Research Agency (RRA): http://rra.go.kr A.5 Taiwan The BM70/71 module has received compliance approval in accordance with the Telecommunications Act. Customers seeking to use the compliance approval in their product should contact Microchip Technology sales or distribution partners to obtain a Letter of Authority. Integration of this module into a final product does not require additional radio certification provided installation instructions are followed and no modifications of the module are allowed. A.5.1 LABELING AND USER INFORMATION REQUIREMENTS For the BM70 module, due to the limited module size, the NCC mark and ID are displayed in the data sheet only and cannot be displayed on the module label: A.5.2 HELPFUL WEB SITES National Communications http://www.ncc.gov.tw A.6 Commission (NCC): China The BM70/71 module has received certification of conformity in accordance with the China MIIT Notice 2014-01 of State Radio Regulation Committee (SRRC) certification scheme. Integration of this module into a final product does not require additional radio certification, provided installation instructions are followed and no modifications of the module are allowed. A.6.1 LABELING AND USER INFORMATION REQUIREMENTS The BM70 module is labeled with its own CMIIT ID as follows: When Host system is using an approved Full Modular Approval (FMA) radio: The host must bear a label containing the statement "This device contains SRRC approved Radio module CMIIT ID: 2015DJ7135". For the BM71 module, due to the limited module size, the NCC mark and ID are displayed in the data sheet only and cannot be displayed on the module label. The BM71 module is labeled with its own CMIIT ID as follows: When Host system is using an approved Full Modular Approval (FMA) radio: The host must bear a label containing the statement "This device contains SRRC approved Radio module CMIIT ID: 2016DJ2787". The user's manual should contain following warning (for RF device) in traditional Chinese: ! A.7 Other Regulatory Jurisdictions * For information about other countries jurisdictions not covered here, refer to the http://www.microchip.com/design-centers/wireless-connectivity. * Should other regulatory jurisdiction certification be required by the customer, or the customer needs to recertify the module for other reasons, contact Microchip for the required utilities and documentation. DS60001372G-Page 60 2015-2018 Microchip Technology Inc. BM70/71 APPENDIX B: REVISION HISTORY Revision A (October 2015) This is the initial released version of the document. Revision B (October 2015) This revision includes the following changes as well as minor updates to text and formatting, which were incorporated throughout the document. TABLE B-1: MAJOR SECTION UPDATES Section "Features" Update Description This section is updated with certification informations. The data from this section has been reformatted and distributed in other sections. "MAC/Baseband/Higher Layer Features", "Power Management", "Operating Conditions",and FIGURE 2: "BM71 MODULE" These sections are newly added. "General Description" This section was previously placed in chapter 1 and has been moved here. 1.0 "Device Overview" Table 1-2, Table 1-4, and Table 1-5 are added. 2.0 "Application Information" This chapter contains information that was previously located in Appendix A and Electrical Characteristics. 8.0 "Ordering Guide" Table 8-1 is updated with Y-axis information and certification information. Appendix A: "Certification Notices" This section is updated with images for the Certification Marking and their numbers. The regulatory information is updated to be the latest. 5.0 "Electrical Characteristics" Table 5-3 is added Revision C (November 2015) Updated Appendix A: "Certification Notices". Revision D (March 2016) This revision includes the following changes as well as minor updates to text and formatting incorporated throughout the document. TABLE D-1: MAJOR SECTION UPDATES Section Update Description 1.1 "Interface Description" This section is updated with a note. Updated Figure 1-1, Figure 1-2, Figure 1-6 2.1 "Reference Schematics" Figure 2-1 through Figure 2-8, Figure 2-10, Figure 5-1, Figure 5-2, Figure 2-11, Figure 4-1 and Table 4-1, Table 8-1 "Absolute Maximum Ratings" Updated this section. 5.1.1 "Tx/Rx current consumption details" Updated this section with new content. 8.0 "Ordering Guide" This section is updated with a note. Appendix A: "Certification Notices" Content has been updated 2015-2018 Microchip Technology Inc. DS60001372G-Page 61 BM70/71 Revision E (January 2017) This revision includes the following changes as well as minor updates to text and formatting, which were incorporated throughout the document. TABLE E-1: MAJOR SECTION UPDATES Section Update Description "Features" Updated this section. "MAC/Baseband/Higher Layer Features" Updated this section. "Power Management" Updated the average current details. "Operating Conditions" Updated the operating temperature details. 1.0 "Device Overview" Updated Figure 1-1, Figure 1-2, Table 1-1 and Table 1-2 Deleted Table 1-4 2.0 "Application Information" Updated Figure 2-9 through Figure 2-11 and Figure 2-14 3.0 "Module Configuration" Added Table 3-2 and updated this section. 4.3 "Antenna Considerations" Added new section. 5.0 "Electrical Characteristics" Updated ambient temperature details for part numbers ending with 0002 and 0B0x. Deleted Table 5-2. Updated Table 5-1, Table 5-3. Added Table 5-2 8.0 "Ordering Guide" Updated Table 8-1 Appendix A: "Certification Notices" Updated this section. Revision F (May 2017) This revision includes the following changes as well as minor updates to text and formatting were incorporated throughout the document. TABLE F-1: MAJOR SECTION UPDATES Section Update Description 1.0 "Device Overview" Updated Table 1-1, Figure 1-6 6.0 "Physical dimensions" Updated Figure 6-5 and Figure 6-6 8.0 "Ordering Guide" Added Regulatory model information in Table 8-1 Appendix A: "Certification Notices" Added the report number of "Radio" certification and notes in Table A-1 and Table A-2 Revision G (January 2018) This revision includes the following changes as well as minor updates to text and formatting were incorporated throughout the document. TABLE G-1: MAJOR SECTION UPDATES Section Update Description "Features" Updated Canada certification information. 1.0 "Device Overview" Updated the NOTE. 2.0 "Application Information" Updated 2.1"Reference Schematics", Figure 2-1, Figure 2-3, Figure 2-5 and Figure 2-7. 8.0 "Ordering Guide" Updated Table 8-1 with Canada regulatory certification information and deleted Microchip IC information. Appendix A: "Certification Notices" Updated the United States, Canada and Europe certification information. Updated KDB and ECC URL links. DS60001372G-Page 62 2015-2018 Microchip Technology Inc. BM70/71 THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or Field Application Engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://microchip.com/support CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under "Support", click on "Customer Change Notification" and follow the registration instructions. 2015-2018 Microchip Technology Inc. DS60001372G-Page 63 BM70/71 NOTES: DS60001372G-Page 64 2015-2018 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2015-2018 Microchip Technology Inc. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, CryptoAuthentication, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2015-2018, Microchip Technology Incorporated, All Rights Reserved. ISBN: 978-1-5224-2621-9 DS60001372G-Page 65 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Australia - Sydney Tel: 61-2-9868-6733 India - Bangalore Tel: 91-80-3090-4444 China - Beijing Tel: 86-10-8569-7000 India - New Delhi Tel: 91-11-4160-8631 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Chengdu Tel: 86-28-8665-5511 India - Pune Tel: 91-20-4121-0141 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 China - Chongqing Tel: 86-23-8980-9588 Japan - Osaka Tel: 81-6-6152-7160 Finland - Espoo Tel: 358-9-4520-820 China - Dongguan Tel: 86-769-8702-9880 Japan - Tokyo Tel: 81-3-6880- 3770 China - Guangzhou Tel: 86-20-8755-8029 Korea - Daegu Tel: 82-53-744-4301 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 China - Hangzhou Tel: 86-571-8792-8115 Korea - Seoul Tel: 82-2-554-7200 China - Hong Kong SAR Tel: 852-2943-5100 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 China - Nanjing Tel: 86-25-8473-2460 Malaysia - Penang Tel: 60-4-227-8870 China - Qingdao Tel: 86-532-8502-7355 Philippines - Manila Tel: 63-2-634-9065 China - Shanghai Tel: 86-21-3326-8000 Singapore Tel: 65-6334-8870 China - Shenyang Tel: 86-24-2334-2829 Taiwan - Hsin Chu Tel: 886-3-577-8366 China - Shenzhen Tel: 86-755-8864-2200 Taiwan - Kaohsiung Tel: 886-7-213-7830 China - Suzhou Tel: 86-186-6233-1526 Taiwan - Taipei Tel: 886-2-2508-8600 China - Wuhan Tel: 86-27-5980-5300 Thailand - Bangkok Tel: 66-2-694-1351 China - Xian Tel: 86-29-8833-7252 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 DS60001372G-page 66 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-67-3636 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra'anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7289-7561 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 2018 Microchip Technology Inc. 10/25/17