TVS Diodes Axial Leaded - 600W > P6KE series P6KE Series RoHS Pb e3 Description The P6KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features Uni-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation by 10/1000s Test Waveform (Fig.2)(Note 1), (Note 4) PPPM 600 W Steady State Power Dissipation on Infinite Heat Sink at TL=75C PD 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only (Note 3) VF 3.5/5.0 V Operating Junction and Storage Temperature Range TJ , TSTG -55 to 175 * 600W peak pulse capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * Glass passivated chip junction in DO-15 Package * Fast response time: typically less than 1.0ps from 0 Volts to BV min * Excellent clamping capability * Typical failure mode is short from over-specified voltage or current * Whisker test conducted based on Table 4a and 4c of JEDEC JESD201A * IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) * EFT protection of data lines in accordance with IEC 61000-4-4 * Low incremental surge resistance * Typical IR less than 1A when VBR min>12V * Compatible with high temperature reflow soldering (260C/40 s) * VBR @ TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient, typical value is 0.1%) * UL Recognized epoxy meeting flammability classification V-0 * Matte tin lead-free plated * Halogen free and RoHS compliant * Pb-free E3 means 2nd level interconnect is Pbfree and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) C Typical Thermal Resistance Junction to Lead RJL 20 C/W Typical Thermal Resistance Junction to Ambient RJA 75 C/W Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) = 25OC per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. 3.VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. 4. The PPPM of stacked-die parts is 800W and please contact littelfuse for the detail stacked-die parts. Applications TVS components are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Additional Infomarion Functional Diagram Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/31/20 TVS Diodes Axial Leaded - 600W > P6KE series Electrical Characteristics (T =25C unless otherwise noted) A Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) P6KE6.8A P6KE7.5A P6KE8.2A P6KE9.1A P6KE10A P6KE11A P6KE12A P6KE13A P6KE15A P6KE16A P6KE18A P6KE20A P6KE22A P6KE24A P6KE27A P6KE30A P6KE33A P6KE36A P6KE39A P6KE43A P6KE47A P6KE51A P6KE56A P6KE62A P6KE68A P6KE75A P6KE82A P6KE91A P6KE100A P6KE110A P6KE120A P6KE130A P6KE150A P6KE160A P6KE170A P6KE180A P6KE200A P6KE220A P6KE250A P6KE300A P6KE350A P6KE400A P6KE440A P6KE480A P6KE510A P6KE530A P6KE540A P6KE550A P6KE600A P6KE6.8CA P6KE7.5CA P6KE8.2CA P6KE9.1CA P6KE10CA P6KE11CA P6KE12CA P6KE13CA P6KE15CA P6KE16CA P6KE18CA P6KE20CA P6KE22CA P6KE24CA P6KE27CA P6KE30CA P6KE33CA P6KE36CA P6KE39CA P6KE43CA P6KE47CA P6KE51CA P6KE56CA P6KE62CA P6KE68CA P6KE75CA P6KE82CA P6KE91CA P6KE100CA P6KE110CA P6KE120CA P6KE130CA P6KE150CA P6KE160CA P6KE170CA P6KE180CA P6KE200CA P6KE220CA P6KE250CA P6KE300CA P6KE350CA P6KE400CA P6KE440CA P6KE480CA P6KE510CA P6KE530CA P6KE540CA P6KE550CA P6KE600CA 5.80 6.40 7.02 7.78 8.55 9.40 10.20 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 30.80 33.30 36.80 40.20 43.60 47.80 53.00 58.10 64.10 70.10 77.80 85.50 94.00 102.00 111.00 128.00 136.00 145.00 154.00 171.00 185.00 214.00 256.00 300.00 342.00 376.00 408.00 434.00 451.00 460.00 468.00 512.00 Breakdown Voltage VBR (Volts) @ IT Min. 6.45 7.13 7.79 8.65 9.50 10.50 11.40 12.40 14.30 15.20 17.10 19.00 20.90 22.80 25.70 28.50 31.40 34.20 37.10 40.90 44.70 48.50 53.20 58.90 64.60 71.30 77.90 86.50 95.00 105.00 114.00 124.00 143.00 152.00 162.00 171.00 190.00 209.00 237.00 285.00 332.00 380.00 418.00 456.00 485.00 503.50 513.00 522.50 570.00 Max. 7.14 7.88 8.61 9.55 10.50 11.60 12.60 13.70 15.80 16.80 18.90 21.00 23.10 25.20 28.40 31.50 34.70 37.80 41.00 45.20 49.40 53.60 58.80 65.10 71.40 78.80 86.10 95.50 105.00 116.00 126.00 137.00 158.00 168.00 179.00 189.00 210.00 231.00 263.00 315.00 368.00 420.00 462.00 504.00 535.00 556.50 567.00 577.50 630.00 (mA) Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR@ VR (A) 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10.5 11.3 12.1 13.4 14.5 15.6 16.7 18.2 21.2 22.5 25.2 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 70.1 77.0 85.0 92.0 103.0 113.0 125.0 137.0 152.0 165.0 179.0 207.0 219.0 234.0 246.0 274.0 328.0 344.0 414.0 482.0 548.0 602.0 658.0 698.0 725.0 740.0 760.0 828.0 58.1 54.0 50.4 45.5 42.1 39.1 36.5 33.5 28.8 27.1 24.2 22.0 19.9 18.4 16.3 14.7 13.3 12.2 11.3 10.3 9.4 8.7 7.9 7.2 6.6 5.9 5.4 4.9 4.5 4.0 3.7 3.4 2.9 2.8 2.6 2.5 2.2 1.9 1.8 1.5 1.3 1.1 1.0 0.9 0.9 0.8 0.8 0.8 0.75 1000 500 200 50 10 5 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Test Current IT Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X - For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is 10% and VC is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred. (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/31/20 TVS Diodes Axial Leaded - 600W > P6KE series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT IT IR Vc VBR VR V IR IT Ipp Ipp PPPM VR VBR VC IR VF V VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS Time TJ initial = TAMB stacked-die, 800W at 10/1000s, 25C 10 1 0.1 0.001 Single die,600W at 10/1000s, 25C 0.01 0.1 1 10 td-Pulse Width (ms) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/31/20 TVS Diodes Axial Leaded - 600W > P6KE series Ratings and Characteristic Curves (T =25C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform 150 100 75 50 25 0 tr=10sec IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 - Peak Pulse Power Derating Curve 0 25 50 75 100 125 150 175 Half Value IPPM IPPM ( ) 2 50 200 0 td 1.0 0 2.0 3.0 4.0 Figure 6 - Typical Transient Thermal Impedance 100 Uni-dire onal V= 0V Bi-direc 1000.00 Transient Thermal Impedance ( C/W) 10000.00 Cj(pf) 10/1000sec. Waveform as defined by R.E.A t-Time (ms) Figure 5 - Typical Junction Capacitance nal V=0V 100.00 1.00 1.00 Peak Value IPPM 100 TJ - Initial Junction Temperature (C) 10.00 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Uni-dire onal Bi-direc nal V= VR 10.00 100.00 VBR--Reverse Breakdown Voltage(V) 1000.00 10 1 0.1 0.01 0.1 1 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100.0 Single die 100 IF - Peak Forward Current(A) IFSM - Peak Forward Surve Current(A) 120 80 60 40 20 Stacked-die 10.0 1.0 0 1 10 Number of Cycles at 60 Hz 100 0.1 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 VF - Peak Forward Voltage(V) (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/31/20 TVS Diodes Axial Leaded - 600W > P6KE series Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (tL) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 30 Seconds Max Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 260C tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Flow/Wave Soldering (Solder Dipping) Peak Temperature : 265OC Dipping Time : 10 seconds Soldering : 1 time Environmental Specifications Physical Specificationst C Weight 0.015oz., 0.4g High Temp. Storage JESD22-A103 Case JEDEC DO-204AC (DO-15) molded plastic body over passivated junction. HTRB JESD22-A108 Temperature Cycling JESD22-A104 Polarity Color band denotes the cathode except Bipolar. H3TRB JESD22-A101 Terminal Matte Tin axial leads, solderable per JESD22-B102. RSH JESD22-B106 Dimensions D Cathode Band (for uni-directional products only) Dimensions C A B A DO-204AC (DO-15) A Inches Millimeters Min Max Min Max 1.000 - 25.40 - B 0.230 0.300 5.80 7.60 C 0.028 0.034 0.71 0.86 D 0.104 0.140 2.60 3.60 (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/31/20 TVS Diodes Axial Leaded - 600W > P6KE series Part Numbering System Part Marking System P6KE xxx XX X Cathode Band Option Code: Blank Reel Tape -B Bulk Packaging F (for uni-directional products only) YYWW Littelfuse Logo Type Code: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) Trace Code Marking YY:Year Code WW: Week Code VBR Voltage Code: (Refer to the Electrical Characteristics table) P6KEXXX Product Type Series Code Packaging Component Package Quantity Packaging Option Packaging Specification P6KExxxXX DO-204AC 4000 Tape & Reel EIA STD RS-296 P6KExxxXX-B DO-204AC 1000 BULK Littelfuse Spec. Part Number Tape and Reel Specification Off Center either side 0.028(0.7) 2.56 (65.0) 0.236 (6.0) 0.047 (1.2) 0.197+/-0.020 (5.0+/- 0.5) 13.0 (330.2) 2.063+0.079/-0.039 (53.0+2.0/-1.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics. (c) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/31/20