DS18B20-PAR/T&R - Maxim Integrated Products, Inc.

1 of 19 111903

FEATURES

· Unique 1-Wire® interface requires only one

port pin for communication

· Derives power from data line (“parasite

power”)—does not need a local power supply

· Multi-drop capability simplifies distributed

temperature sensing applications

· Requires no external components

· ±0.5°C accuracy from –10°C to +85°C

· Measures temperatures from –55°C to

+100°C (–67°F to +212°F)

· Thermometer resolution is user-selectable

from 9 to 12 bits

· Converts temperature to 12-bit digital word in

750 ms (max.)

· User–definable non-volatile temperature

alarm settings

· Alarm search command identifies and

addresses devices whose temperature is

outside of programmed limits (temperature

alarm condition)

· Software compatible with the DS1822-PAR

· Ideal for use in remote sensing applications

(e.g., temperature probes) that do not have a

local power source

PIN ASSIGNMENT

PIN DESCRIPTION

GND - Ground

DQ - Data In/Out

NC - No Connect

DESCRIPTION

The DS18B20-PAR digital thermometer provides 9 to 12–bit centigrade temperature measurements and

has an alarm function with nonvolatile user-programmable upper and lower trigger points. The

DS18B20-PAR does not need an external power supply because it derives power directly from the data

line (“parasite power”). The DS18B20-PAR communicates over a 1-Wire bus, which by definition

requires only one data line (and ground) for communication with a central microprocessor. It has an

operating temperature range of –55°C to +100°C and is accurate to ±0.5°C over a range of –10°C to

+85°C.

Each DS18B20-PAR has a unique 64-bit identification code, which allows multiple DS18B20-PARs to

function on the same 1–wire bus; thus, it is simple to use one microprocessor to control many DS18B20-

PARs distributed over a large area. Applications that can benefit from this feature include HVAC

environmental controls, temperature monitoring systems inside buildings, equipment or machinery, and

process monitoring and control systems.

DS18B20-PAR

1-Wire Parasite-Powe

Digital Thermomete

www.

maxim

.com

TO-92

(

DS18B20-PAR

)

(

BOTTOM VIEW

)

DALLAS

18B20P

GND

1-Wire is a registered trademark of Dallas Semiconductor.

DS18B20-PAR

2 of 19

DETAILED PIN DESCRIPTIONS Table 1

PIN SYMBOL DESCRIPTION

1 GND Ground.

2DQ

Data Input/Output pin. Open-drain 1-Wire interface pin. Also provides power

to the device when used in parasite power mode (see “Parasite Power” section.)

3NCNo Connect. Doesn’t connect to internal circuit.

OVERVIEW

The DS18B20-PAR uses Dallas’ exclusive 1-Wire bus protocol that implements bus communication

using one control signal. The control line requires a weak pullup resistor since all devices are linked to

the bus via a 3-state or open-drain port (the DQ pin in the case of the DS18B20-PAR). In this bus

system, the microprocessor (the master device) identifies and addresses devices on the bus using each

device’s unique 64-bit code. Because each device has a unique code, the number of devices that can be

addressed on one bus is virtually unlimited. The 1-Wire bus protocol, including detailed explanations of

the commands and “time slots,” is covered in the 1-WIRE BUS SYSTEM section of this datasheet.

An important feature of the DS18B20-PAR is its ability to operate without an external power supply.

Power is instead supplied through the 1-Wire pullup resistor via the DQ pin when the bus is high. The

high bus signal also charges an internal capacitor (CPP), which then supplies power to the device when the

bus is low. This method of deriving power from the 1-Wire bus is referred to as “parasite power.”

Figure 1 shows a block diagram of the DS18B20-PAR, and pin descriptions are given in Table 1. The

64-bit ROM stores the device’s unique serial code. The scratchpad memory contains the 2-byte

temperature register that stores the digital output from the temperature sensor. In addition, the scratchpad

provides access to the 1-byte upper and lower alarm trigger registers (TH and TL). The TH and TL

registers are nonvolatile (EEPROM), so they will retain their data when the device is powered down.

DS18B20-PAR BLOCK DIAGRAM Figure 1

CPP

VPU

4.7K

64-BIT ROM

AND

1-wire PORT

INTERNAL VDD

PARASITE POWER

CIRCUIT MEMORY CONTROL

LOGIC

SCRATCHPAD

8-BIT CRC GENERATOR

TEMPERATURE SENSOR

ALARM HIGH TRIGGER (TH)

ALARM LOW TRIGGER (TL)

CONFIGURATION REGISTER

(EEPROM)

GND

DS18B20-PAR

3 of 19

PARASITE POWER

The DS18B20-PAR’s parasite power circuit allows the DS18B20-PAR to operate without a local external

power supply. This ability is especially useful for applications that require remote temperature sensing or

that are very space constrained. Figure 1 shows the DS18B20-PAR’s parasite-power control circuitry,

which “steals” power from the 1-Wire bus via the DQ pin when the bus is high. The stolen charge

powers the DS18B20-PAR while the bus is high, and some of the charge is stored on the parasite power

capacitor (CPP) to provide power when the bus is low.

The 1-Wire bus and CPP can provide sufficient parasite power to the DS18B20-PAR for most operations

as long as the specified timing and voltage requirements are met (refer to the DC ELECTRICAL

CHARACTERISTICS and the AC ELECTRICAL CHARACTERISTICS sections of this data sheet).

However, when the DS18B20-PAR is performing temperature conversions or copying data from the

scratchpad memory to EEPROM, the operating current can be as high as 1.5 mA. This current can cause

an unacceptable voltage drop across the weak 1-Wire pullup resistor and is more current than can be

supplied by CPP. To assure that the DS18B20-PAR has sufficient supply current, it is necessary to

provide a strong pullup on the 1-Wire bus whenever temperature conversions are taking place or data is

being copied from the scratchpad to EEPROM. This can be accomplished by using a MOSFET to pull

the bus directly to the rail as shown in Figure 2. The 1-Wire bus must be switched to the strong pullup

within 10 ms (max) after a Convert T [44h] or Copy Scratchpad [48h] command is issued, and the bus

must be held high by the pullup for the duration of the conversion (tconv) or data transfer (twr = 10 ms).

No other activity can take place on the 1-Wire bus while the pullup is enabled.

SUPPLYING THE DS18B20-PAR DURING TEMPERATURE CONVERSIONS

Figure 2

OPERATION – MEASURING TEMPERATURE

The core functionality of the DS18B20-PAR is its direct-to-digital temperature sensor. The resolution of

the temperature sensor is user-configurable to 9, 10, 11, or 12 bits, which corresponds to increments of

0.5°C, 0.25°C, 0.125°C, and 0.0625°C, respectively. The default resolution at power-up is 12-bit.

The DS18B20-PAR powers-up in a low-power idle state; to initiate a temperature measurement and A-to-

D conversion, the master must issue a Convert T [44h] command. Following the conversion, the

resulting thermal data is stored in the 2-byte temperature register in the scratchpad memory and the

DS18B20-PAR returns to its idle state. The DS18B20-PAR output data is calibrated in degrees

centigrade; for Fahrenheit applications, a lookup table or conversion routine must be used. The

temperature data is stored as a 16-bit sign-extended two’s complement number in the temperature register

(see Figure 3). The sign bits (S) indicate if the temperature is positive or negative: for positive numbers S

= 0 and for negative numbers S = 1. If the DS18B20-PAR is configured for 12-bit resolution, all bits in

the temperature register will contain valid data. For 11-bit resolution, bit 0 is undefined. For 10-bit

VPU

4.7K

1-Wire Bus

Micro-

processor

DS18B20-PA

GND DQ

To Other

1-Wire Devices

DS18B20-PAR

4 of 19

resolution, bits 1 and 0 are undefined, and for 9-bit resolution bits 2, 1 and 0 are undefined. Table 2 gives

examples of digital output data and the corresponding temperature reading for 12-bit resolution

conversions.

TEMPERATURE REGISTER FORMAT Figure 3

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

LS Byte 232221202-1 2-2 2-3 2-4

bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8

MS Byte SSSSS2

62524

TEMPERATURE/DATA RELATIONSHIP Table 2

TEMPERATURE DIGITAL OUTPUT

(Binary)

DIGITAL OUTPUT

(Hex)

+85°C* 0000 0101 0101 0000 0550h

+25.0625°C 0000 0001 1001 0001 0191h

+10.125°C 0000 0000 1010 0010 00A2h

+0.5°C 0000 0000 0000 1000 0008h

0°C 0000 0000 0000 0000 0000h

-0.5°C 1111 1111 1111 1000 FFF8h

-10.125°C 1111 1111 0101 1110 FF5Eh

-25.0625°C 1111 1110 0110 1111 FE6Fh

-55°C 1111 1100 1001 0000 FC90h

*The power-on reset value of the temperature register is +85°C

OPERATION – ALARM SIGNALING

After the DS18B20-PAR performs a temperature conversion, the temperature value is compared to the

user-defined two’s complement alarm trigger values stored in the 1-byte TH and TL registers (see Figure

4). The sign bit (S) indicates if the value is positive or negative: for positive numbers S = 0 and for

negative numbers S = 1. The TH and TL registers are nonvolatile (EEPROM) so they will retain data

when the device is powered down. TH and TL can be accessed through bytes 2 and 3 of the scratchpad as

explained in the MEMORY section of this datasheet.

TH AND TL REGISTER FORMAT Figure 4

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

6252525222120

Only bits 11 through 4 of the temperature register are used in the TH and TL comparison since TH and TL

are 8-bit registers. If the result of a temperature measurement is higher than TH or lower than TL, an

alarm condition exists and an alarm flag is set inside the DS18B20-PAR. This flag is updated after every

temperature measurement; therefore, if the alarm condition goes away, the flag will be turned off after the

next temperature conversion.

DS18B20-PAR

5 of 19

The master device can check the alarm flag status of all DS DS18B20-PARs on the bus by issuing an

Alarm Search [ECh] command. Any DS18B20-PARs with a set alarm flag will respond to the command,

so the master can determine exactly which DS18B20-PARs have experienced an alarm condition. If an

alarm condition exists and the TH or TL settings have changed, another temperature conversion should be

done to validate the alarm condition.

64-BIT LASERED ROM CODE

Each DS18B20-PAR contains a unique 64–bit code (see Figure 5) stored in ROM. The least significant 8

bits of the ROM code contain the DS18B20-PAR’s 1–wire family code: 28h. The next 48 bits contain a

unique serial number. The most significant 8 bits contain a cyclic redundancy check (CRC) byte that is

calculated from the first 56 bits of the ROM code. A detailed explanation of the CRC bits is provided in

the CRC GENERATION section. The 64–bit ROM code and associated ROM function control logic

allow the DS18B20-PAR to operate as a 1–wire device using the protocol detailed in the 1-WIRE BUS

SYSTEM section of this datasheet.

64-BIT LASERED ROM CODE Figure 5

8-BIT CRC 48-BIT SERIAL NUMBER 8-BIT FAMILY CODE (28h)

MEMORY

The DS18B20-PAR’s memory is organized as shown in Figure 6. The memory consists of an SRAM

scratchpad with nonvolatile EEPROM storage for the high and low alarm trigger registers (TH and TL)

and configuration register. Note that if the DS18B20-PAR alarm function is not used, the TH and TL

registers can serve as general-purpose memory. All memory commands are described in detail in the

DS18B20-PAR FUNCTION COMMANDS section.

Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,

respectively. These bytes are read-only. Bytes 2 and 3 provide access to TH and TL registers. Byte 4

contains the configuration register data, which is explained in detail in the CONFIGURATION

cannot be overwritten; these bytes will return all 1s when read.

Byte 8 of the scratchpad is read-only and contains the cyclic redundancy check (CRC) code for bytes 0

through 7 of the scratchpad. The DS18B20-PAR generates this CRC using the method described in the

CRC GENERATION section.

Data is written to bytes 2, 3, and 4 of the scratchpad using the Write Scratchpad [4Eh] command, and the

data must be transmitted to the DS18B20-PAR starting with the least significant bit of byte 2. To verify

data integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is

written. When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least

significant bit of byte 0. To transfer the TH, TL and configuration data from the scratchpad to EEPROM,

the master must issue the Copy Scratchpad [48h] command.

Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM

data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM

to the scratchpad at any time using the Recall E2 [B8h] command. The master can issue “read time slots”

(see the 1-WIRE BUS SYSTEM section) following the Recall E2 command and the DS18B20-PAR will

indicate the status of the recall by transmitting 0 while the recall is in progress and 1 when the recall is

done.

MSB MSBLSB LSB LSBMSB

DS18B20-PAR

6 of 19

DS18B20-PAR MEMORY MAP Figure 6

SCRATCHPAD (Power-up State)

byte 0 Temperature LSB (50h)

byte 1 Temperature MSB (05h) EEPROM

byte 2 TH Register or User Byte 1* TH Register or User Byte 1

byte 3 TL Register or User Byte 2* TL Register or User Byte 2

byte 4 Configuration Register* Configuration Register

byte 5 Reserved (FFh)

byte 6 Reserved (0Ch)

byte 7 Reserved (10h)

byte 8 CRC*

*Power-up state depends on value(s) stored

in EEPROM

CONFIGURATION REGISTER

Byte 4 of the scratchpad memory contains the configuration register, which is organized as illustrated in

Figure 7. The user can set the conversion resolution of the DS18B20-PAR using the R0 and R1 bits in

this register as shown in Table 3. The power-up default of these bits is R0 = 1 and R1 = 1 (12-bit

resolution). Note that there is a direct tradeoff between resolution and conversion time. Bit 7 and bits 0-4

in the configuration register are reserved for internal use by the device and cannot be overwritten; these

bits will return 1s when read.

CONFIGURATION REGISTER Figure 7

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

0R1R011111

THERMOMETER RESOLUTION CONFIGURATION Table 3

R1 R0 Resolution Max Conversion Time

0 0 9-bit 93.75 ms (tCONV/8)

0 1 10-bit 187.5 ms (tCONV/4)

1 0 11-bit 375 ms (tCONV/2)

1 1 12-bit 750 ms (tCONV)

CRC GENERATION

CRC bytes are provided as part of the DS18B20-PAR’s 64-bit ROM code and in the 9th byte of the

scratchpad memory. The ROM code CRC is calculated from the first 56 bits of the ROM code and is

contained in the most significant byte of the ROM. The scratchpad CRC is calculated from the data

stored in the scratchpad, and therefore it changes when the data in the scratchpad changes. The CRCs

provide the bus master with a method of data validation when data is read from the DS18B20-PAR. To

(85°C)

DS18B20-PAR

7 of 19

verify that data has been read correctly, the bus master must re-calculate the CRC from the received data

and then compare this value to either the ROM code CRC (for ROM reads) or to the scratchpad CRC (for

scratchpad reads). If the calculated CRC matches the read CRC, the data has been received error free. The

comparison of CRC values and the decision to continue with an operation are determined entirely by the

bus master. There is no circuitry inside the DS18B20-PAR that prevents a command sequence from

proceeding if the DS18B20-PAR CRC (ROM or scratchpad) does not match the value generated by the

bus master.

The equivalent polynomial function of the CRC (ROM or scratchpad) is: CRC = X8 + X5 + X4 + 1

The bus master can re-calculate the CRC and compare it to the CRC values from the DS18B20-PAR

using the polynomial generator shown in Figure 8. This circuit consists of a shift register and XOR gates,

and the shift register bits are initialized to 0. Starting with the least significant bit of the ROM code or the

least significant bit of byte 0 in the scratchpad, one bit at a time should shifted into the shift register.

After shifting in the 56th bit from the ROM or the most significant bit of byte 7 from the scratchpad, the

polynomial generator will contain the re-calculated CRC. Next, the 8-bit ROM code or scratchpad CRC

from the DS18B20-PAR must be shifted into the circuit. At this point, if the re-calculated CRC was

correct, the shift register will contain all 0s. Additional information about the Dallas 1-Wire cyclic

redundancy check is available in Application Note 27 entitled “Understanding and Using Cyclic

Redundancy Checks with Dallas Semiconductor Touch Memory Products.”

CRC GENERATOR Figure 8

1-WIRE BUS SYSTEM

The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS18B20-

PAR is always a slave. When there is only one slave on the bus, the system is referred to as a “single-

drop” system; the system is “multi-drop” if there are multiple slaves on the bus.

All data and commands are transmitted least significant bit first over the 1-Wire bus.

The following discussion of the 1-Wire bus system is broken down into three topics: hardware

configuration, transaction sequence, and 1-Wire signaling (signal types and timing).

HARDWARE CONFIGURATION

The 1-Wire bus has by definition only a single data line. Each device (master or slave) interfaces to the

data line via an open drain or 3–state port. This allows each device to “release” the data line when the

device is not transmitting data so the bus is available for use by another device. The 1-Wire port of the

DS18B20-PAR (the DQ pin) is open drain with an internal circuit equivalent to that shown in Figure 9.

The 1-Wire bus requires an external pullup resistor of approximately 5 kW; thus, the idle state for the 1-

Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle

state if the transaction is to resume. Infinite recovery time can occur between bits so long as the 1-Wire

bus is in the inactive (high) state during the recovery period. If the bus is held low for more than 480 ms,

all components on the bus will be reset. In addition, to assure that the DS18B20-PAR has sufficient

supply current during temperature conversions, it is necessary to provide a strong pullup (such as a

MOSFET) on the 1-Wire bus whenever temperature conversions or EEPROM writes are taking place (as

described in the PARASITE POWER section).

(MSB) (LSB)

XOR XOR XOR

INPUT

DS18B20-PAR

8 of 19

HARDWARE CONFIGURATION Figure 9

TRANSACTION SEQUENCE

The transaction sequence for accessing the DS18B20-PAR is as follows:

Step 1. Initialization

Step 2. ROM Command (followed by any required data exchange)

Step 3. DS18B20-PAR Function Command (followed by any required data exchange)

It is very important to follow this sequence every time the DS18B20-PAR is accessed, as the DS18B20-

PAR will not respond if any steps in the sequence are missing or out of order. Exceptions to this rule are

the Search ROM [F0h] and Alarm Search [ECh] commands. After issuing either of these ROM

commands, the master must return to Step 1 in the sequence.

INITIALIZATION

All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence

consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the

slave(s). The presence pulse lets the bus master know that slave devices (such as the DS18B20-PAR) are

on the bus and are ready to operate. Timing for the reset and presence pulses is detailed in the

1-WIRE SIGNALING section.

ROM COMMANDS

After the bus master has detected a presence pulse, it can issue a ROM command. These commands

operate on the unique 64–bit ROM codes of each slave device and allow the master to single out a

specific device if many are present on the 1-Wire bus. These commands also allow the master to

determine how many and what types of devices are present on the bus or if any device has experienced an

alarm condition. There are five ROM commands, and each command is 8 bits long. The master device

must issue an appropriate ROM command before issuing a DS18B20-PAR function command. A

flowchart for operation of the ROM commands is shown in Figure 10.

SEARCH ROM [F0h]

When a system is initially powered up, the master must identify the ROM codes of all slave devices on

the bus, which allows the master to determine the number of slaves and their device types. The master

learns the ROM codes through a process of elimination that requires the master to perform a Search ROM

VPU

4.7K

5 µA

Typ.

DS18B20-PAR 1-WIRE PORT

100 W

FET

RX = RECEIVE

TX = TRANSMIT

1-wire bus

VPU

Micro-

processor Strong

Pullup

DS18B20-PAR

9 of 19

cycle (i.e., Search ROM command followed by data exchange) as many times as necessary to identify all

of the slave devices. If there is only one slave on the bus, the simpler Read ROM command (see below)

can be used in place of the Search ROM process. For a detailed explanation of the Search ROM

procedure, refer to the iButton® Book of Standards at www.ibutton.com/ibuttons/standard.pdf. After

every Search ROM cycle, the bus master must return to Step 1 (Initialization) in the transaction sequence.

READ ROM [33h]

This command can only be used when there is one slave on the bus. It allows the bus master to read the

slave’s 64-bit ROM code without using the Search ROM procedure. If this command is used when there

is more than one slave present on the bus, a data collision will occur when all the slaves attempt to

respond at the same time.

MATCH ROM [55h]

The match ROM command followed by a 64–bit ROM code sequence allows the bus master to address a

specific slave device on a multi-drop or single-drop bus. Only the slave that exactly matches the 64–bit

ROM code sequence will respond to the function command issued by the master; all other slaves on the

bus will wait for a reset pulse.

SKIP ROM [CCh]

The master can use this command to address all devices on the bus simultaneously without sending out

any ROM code information. For example, the master can make all DS18B20-PARs on the bus perform

simultaneous temperature conversions by issuing a Skip ROM command followed by a Convert T [44h]

command. Note, however, that the Skip ROM command can only be followed by the Read Scratchpad

[BEh] command when there is one slave on the bus. This sequence saves time by allowing the master to

read from the device without sending its 64–bit ROM code. This sequence will cause a data collision on

the bus if there is more than one slave since multiple devices will attempt to transmit data simultaneously.

ALARM SEARCH [ECh]

The operation of this command is identical to the operation of the Search ROM command except that

only slaves with a set alarm flag will respond. This command allows the master device to determine if

any DS18B20-PARs experienced an alarm condition during the most recent temperature conversion.

After every Alarm Search cycle (i.e., Alarm Search command followed by data exchange), the bus master

must return to Step 1 (Initialization) in the transaction sequence. Refer to the OPERATION – ALARM

SIGNALING section for an explanation of alarm flag operation.

DS18B20-PAR FUNCTION COMMANDS

After the bus master has used a ROM command to address the DS18B20-PAR with which it wishes to

communicate, the master can issue one of the DS18B20-PAR function commands. These commands

allow the master to write to and read from the DS18B20-PAR’s scratchpad memory, initiate temperature

conversions and determine the power supply mode. The DS18B20-PAR function commands, which are

described below, are summarized in Table 4 and illustrated by the flowchart in Figure 11.

CONVERT T [44h]

This command initiates a single temperature conversion. Following the conversion, the resulting thermal

data is stored in the 2-byte temperature register in the scratchpad memory and the DS18B20-PAR returns

to its low-power idle state. Within 10 ms (max) after this command is issued the master must enable a

strong pullup on the 1-Wire bus for the duration of the conversion (tconv) as described in the PARASITE

POWER section.

WRITE SCRATCHPAD [4Eh]

This command allows the master to write 3 bytes of data to the DS18B20-PAR’s scratchpad. The first

data byte is written into the TH register (byte 2 of the scratchpad), the second byte is written into the TL

iButton is a registered trademark of Dallas Semiconductor.

DS18B20-PAR

10 of 19

transmitted least significant bit first. All three bytes MUST be written before the master issues a reset, or

the data may be corrupted.

READ SCRATCHPAD [BEh]

This command allows the master to read the contents of the scratchpad. The data transfer starts with the

least significant bit of byte 0 and continues through the scratchpad until the 9th byte (byte 8 – CRC) is

read. If only part of the scratchpad contents is required, the master may issue a reset to terminate reading

at any time.

COPY SCRATCHPAD [48h]

This command copies the contents of the scratchpad TH, TL and configuration registers (bytes 2, 3 and 4)

to EEPROM. Within 10 ms (max) after this command is issued the master must enable a strong pullup on

the 1-Wire bus for at least 10 ms as described in the PARASITE POWER section.

RECALL E2 [B8h]

This command recalls the alarm trigger values (TH and TL) and configuration data from EEPROM and

places the data in bytes 2, 3, and 4, respectively, in the scratchpad memory. The master device can issue

“read time slots” (see the 1-WIRE BUS SYSTEM section) following the Recall E2 command and the

DS18B20-PAR will indicate the status of the recall by transmitting 0 while the recall is in progress and

1 when the recall is done. The recall operation happens automatically at power-up, so valid data is

available in the scratchpad as soon as power is applied to the device.

DS18B20-PAR Function Command Set Table 4

Command Description Protocol

1-Wire Bus Activity

After Command is Issued Notes

TEMPERATURE CONVERSION COMMANDS

Convert T Initiates temperature

conversion.

44h None 1

MEMORY COMMANDS

Read Scratchpad Reads the entire scratchpad

including the CRC byte.

BEh DS18B20-PAR transmits up

to 9 data bytes to master.

Write Scratchpad Writes data into scratchpad

bytes 2, 3, and 4 (TH, TL, and

configuration registers).

4Eh Master transmits 3 data

bytes to DS18B20-PAR.

Copy Scratchpad Copies TH, TL, and

configuration register data from

the scratchpad to EEPROM.

48h None 1

Recall E2Recalls TH, TL, and

configuration register data from

EEPROM to the scratchpad.

B8h DS18B20-PAR transmits

recall status to master.

NOTES:

1. The master must enable a strong pullup on the 1-Wire bus during temperature conversions and copies

from the scratchpad to EEPROM. No other bus activity may take place during this time.

2. The master can interrupt the transmission of data at any time by issuing a reset.

3. All three bytes must be written before a reset is issued.

DS18B20-PAR

11 of 19

ROM COMMANDS FLOW CHART Figure 10

CCh

SKIP ROM

COMMAND

MASTER TX

RESET PULSE

DS18B20-PAR

TX PRESENCE

PULSE

MASTER TX ROM

COMMAND

33h

READ ROM

COMMAND

55h

MATCH ROM

COMMAND

F0h

SEARCH ROM

COMMAND

ECh

ALARM SEARCH

COMMAND

MASTER TX

BIT 0

MAT

MASTER TX

BIT 1

MAT

BIT 63

MATCH?

MASTER TX

BIT 63

YYYY

BIT 0

MAT

BIT 1

MAT

BIT 63

MATCH?

DS18B20-PAR TX

FAMILY CODE

1 BYTE

DS18B20-PAR TX

SERIAL NUMBER

6 BYTES

DS18B20-PAR TX

CRC BYTE

DS18B20-PAR T

BIT 0

DS18B20-PAR TX BIT 0

MASTER TX BIT 0

DEVICE(S)

WITH ALARM

FLAG SET?

Initialization

Sequence

MASTER TX

FUNCTION

COMMAND

(FIGURE 11)

DS18B20-PAR T

BIT 0

DS18B20-PAR TX BIT 0

MASTER TX BIT 0

DS18B20-PAR T

BIT 1

DS18B20-PAR TX BIT 1

MASTER TX BIT 1

DS18B20-PAR T

BIT 63

DS18B20-PAR TX BIT 63

MASTER TX BIT 63

DS18B20-PAR

12 of 19

DS18B20-PAR FUNCTION COMMANDS FLOW CHART Figure 11

MASTER TX

FUNCTION

COMMAND

44h

CONVERT

TEMPERATURE

MASTER ENABLES

STRONG PULLUP ON DQ

DS18B20-PAR CONVERTS

TEMPERATURE

MASTER DISABLES

STRONG PULLUP

48h

COPY

SCRATCHPAD

MASTER ENABLES

STRONG PULL-UP ON DQ

DATA COPIED FROM

SCRATCHPAD TO EEPROM

MASTER DISABLES

STRONG PULLUP

RETURN TO INITIALIZATION

SEQUENCE (FIGURE 10) FOR

NEXT TRANSACTION

BEh

READ

SCRATCHPAD

HAVE 8 BYTES

BEEN READ

MASTER

TX RESET

MASTER RX DATA BYTE

FROM SCRATCHPAD

MASTER RX SCRATCHPAD

CRC BYTE

MASTER

RX “1s”

NB8h

RECALL E2

MASTER BEGINS DATA

RECALL FROM E2 PROM

DEVICE

BUSY RECALLING

DATA

MASTER

RX “0s”

MASTER TX TH BYTE

TO SCRATCHPAD

4Eh

WRITE

SCRATCHPAD

MASTER TX TL BYTE

TO SCRATCHPAD

MASTER TX CONFIG. BYTE

TO SCRATCHPAD

DS18B20-PAR

13 of 19

1-WIRE SIGNALING

The DS18B20-PAR uses a strict 1-Wire communication protocol to insure data integrity. Several signal

types are defined by this protocol: reset pulse, presence pulse, write 0, write 1, read 0, and read 1. All of

these signals, with the exception of the presence pulse, are initiated by the bus master.

INITIALIZATION PROCEDURE: RESET AND PRESENCE PULSES

All communication with the DS18B20-PAR begins with an initialization sequence that consists of a reset

pulse from the master followed by a presence pulse from the DS18B20-PAR. This is illustrated in

Figure 12. When the DS18B20-PAR sends the presence pulse in response to the reset, it is indicating to

the master that it is on the bus and ready to operate.

During the initialization sequence the bus master transmits (TX) the reset pulse by pulling the 1-Wire bus

low for a minimum of 480 ms. The bus master then releases the bus and goes into receive mode (RX).

When the bus is released, the 5k pullup resistor pulls the 1-Wire bus high. When the DS18B20-PAR

detects this rising edge, it waits 15–60 ms and then transmits a presence pulse by pulling the 1-Wire bus

low for 60–240 ms.

INITIALIZATION TIMING Figure 12

READ/WRITE TIME SLOTS

The bus master writes data to the DS18B20-PAR during write time slots and reads data from the

DS18B20-PAR during read time slots. One bit of data is transmitted over the 1-Wire bus per time slot.

WRITE TIME SLOTS

There are two types of write time slots: “Write 1” time slots and “Write 0” time slots. The bus master

uses a Write 1 time slot to write a logic 1 to the DS18B20-PAR and a Write 0 time slot to write a logic 0

to the DS18B20-PAR. All write time slots must be a minimum of 60 ms in duration with a minimum of a

1 ms recovery time between individual write slots. Both types of write time slots are initiated by the

master pulling the 1-Wire bus low (see Figure 13).

To generate a Write 1 time slot, after pulling the 1-Wire bus low, the bus master must release the 1-Wire

bus within 15 ms. When the bus is released, the 5k pullup resistor will pull the bus high. To generate a

Write 0 time slot, after pulling the 1-Wire bus low, the bus master must continue to hold the bus low for

the duration of the time slot (at least 60 ms).

LINE TYPE LEGEND

Bus master pulling low

DS18B20-PAR pulling low

Resistor

ullu

VPU

GND

1-WIRE BUS

480 ms minimum 480 ms minimum

DS18B20-PAR TX

presence pulse

60-240 ms

MASTER TX RESET PULSE MASTER

DS18B20-PA

waits 15-60 ms

DS18B20-PAR

14 of 19

The DS18B20-PAR samples the 1-Wire bus during a window that lasts from 15 ms to 60 ms after the

master initiates the write time slot. If the bus is high during the sampling window, a 1 is written to the

DS18B20-PAR. If the line is low, a 0 is written to the DS18B20-PAR.

READ/WRITE TIME SLOT TIMING DIAGRAM Figure 13

READ TIME SLOTS

The DS18B20-PAR can only transmit data to the master when the master issues read time slots.

Therefore, the master must generate read time slots immediately after issuing a Read Scratchpad [BEh]

command, so that the DS18B20-PAR can provide the requested data. In addition, the master can generate

read time slots after issuing a Recall E2 [B8h] command to find out the recall status as explained in the

DS18B20-PAR FUNCTION COMMAND section.

All read time slots must be a minimum of 60 ms in duration with a minimum of a 1 ms recovery time

between slots. A read time slot is initiated by the master device pulling the 1-Wire bus low for a

minimum of 1 ms and then releasing the bus (see Figure 13). After the master initiates the read time slot,

the DS18B20-PAR will begin transmitting a 1 or 0 on bus. The DS18B20-PAR transmits a 1 by leaving

the bus high and transmits a 0 by pulling the bus low. When transmitting a 0, the DS18B20-PAR will

release the bus by the end of the time slot, and the bus will be pulled back to its high idle state by the

pullup resister. Output data from the DS18B20-PAR is valid for 15 ms after the falling edge that initiated

45 ms

15 ms

VPU

GND

1-WIRE BUS

60 ms < TX “0” < 120

1 ms < TREC < ¥

DS18B20-PAR samples

MIN TYP MA

15 ms30 ms

> 1 ms

MASTER WRITE “0” SLOT MASTER WRITE “1” SLOT

DS18B20-PAR samples

MIN TYP MA

VPU

GND

1-WIRE BUS

15 ms

MASTER READ “0” SLOT MASTER READ “1” SLOT

Master samples Master samples

START

OF SLOT

START

OF SLOT

> 1 ms

1 ms < TREC < ¥

15 ms15 ms30 ms

15 ms

LINE TYPE LEGEND

Bus master pulling low DS18B20-PAR pulling low

Resistor pullup

> 1 ms

DS18B20-PAR

15 of 19

the read time slot. Therefore, the master must release the bus and then sample the bus state within 15 ms

from the start of the slot.

Figure 14 illustrates that the sum of TINIT, TRC, and TSAMPLE must be less than 15 ms for a read time slot.

Figure 15 shows that system timing margin is maximized by keeping TINIT and TRC as short as possible

and by locating the master sample time during read time slots towards the end of the 15 ms period.

DETAILED MASTER READ 1 TIMING Figure 14

RECOMMENDED MASTER READ 1 TIMING Figure 15

DS18B20-PAR OPERATION EXAMPLE 1

In this example there are multiple DS18B20-PARs on the bus. The bus master initiates a temperature

conversion in a specific DS18B20-PAR and then reads its scratchpad and recalculates the CRC to verify

the data.

MASTER MODE DATA (LSB FIRST) COMMENTS

TX Reset Master issues reset pulse.

RX Presence DS18B20-PARs respond with presence pulse.

TX 55h Master issues Match ROM command.

TX 64-bit ROM code Master sends DS18B20-PAR ROM code.

TX 44h Master issues Convert T command.

TX DQ line held high by

strong pullup

Master applies strong pullup to DQ for the duration of the

conversion (tconv).

TX Reset Master issues reset pulse.

RX Presence DS18B20-PARs respond with presence pulse.

TX 55h Master issues Match ROM command.

TX 64-bit ROM code Master sends DS18B20-PAR ROM code.

TX BEh Master issues Read Scratchpad command.

VPU

GND

1-WIRE BUS

15 ms

IH of Master

TRC

TINT > 1 msMaster samples

LINE TYPE LEGEND

Bus master pulling low

Resistor pullup

VPU

GND

1-WIRE BUS

15 ms

IH of Master

TRC =

small

TINT =

small

Master samples

DS18B20-PAR

16 of 19

MASTER MODE DATA (LSB FIRST) COMMENTS

RX 9 data bytes Master reads entire scratchpad including CRC. The master

then recalculates the CRC of the first eight data bytes from the

scratchpad and compares the calculated CRC with the read

CRC (byte 9). If they match, the master continues; if not, the

read operation is repeated.

DS18B20-PAR OPERATION EXAMPLE 2

In this example there is only one DS18B20-PAR on the bus. The master writes to the TH, TL, and

configuration registers in the DS18B20-PAR scratchpad and then reads the scratchpad and recalculates

the CRC to verify the data. The master then copies the scratchpad contents to EEPROM.

MASTER MODE DATA (LSB FIRST) COMMENTS

TX Reset Master issues reset pulse.

RX Presence DS18B20-PAR responds with presence pulse.

TX CCh Master issues Skip ROM command.

TX 4Eh Master issues Write Scratchpad command.

TX 3 data bytes Master sends three data bytes to scratchpad (TH, TL, and config).

TX Reset Master issues reset pulse.

RX Presence DS18B20-PAR responds with presence pulse.

TX CCh Master issues Skip ROM command.

TX BEh Master issues Read Scratchpad command.

RX 9 data bytes Master reads entire scratchpad including CRC. The master then

recalculates the CRC of the first eight data bytes from the

scratchpad and compares the calculated CRC with the read CRC

(byte 9). If they match, the master continues; if not, the read

operation is repeated.

TX Reset Master issues reset pulse.

RX Presence DS18B20-PAR responds with presence pulse.

TX CCh Master issues Skip ROM command.

TX 48h Master issues Copy Scratchpad command.

TX DQ line held high by

strong pullup

Master applies strong pullup to DQ for at least 10 ms while copy

operation is in progress.

DS18B20-PAR

17 of 19

ABSOLUTE MAXIMUM RATINGS*

Voltage on any pin relative to ground –0.5V to +6.0V

Operating temperature –55°C to +100°C

Storage temperature –55°C to +125°C

Soldering temperature See J-STD-020A Specification

*These are stress ratings only and functional operation of the device at these or any other conditions

above those indicated in the operation sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods of time may affect reliability.

DC ELECTRICAL CHARACTERISTICS (-55°C to +100°C; VPU=3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Pullup Supply

Voltage

VPU 3.0 5.5 V 1,2

Thermometer Error tERR -10°C to +85°C ±½ °C 3

-55°C to +100°C ±2

Input Logic Low VIL -0.3 +0.8 V 1,4,5

Input Logic High VIH 3.0 5.5 V 1,6

Sink Current ILVI/O=0.4V 4.0 mA 1

Active Current IDQA 1 1.5 mA 7

DQ Input Current IDQ 5µA8

Drift ±0.2 °C 9

NOTES:

1. All voltages are referenced to ground.

2. The Pullup Supply Voltage specification assumes that the pullup device (resistor or transistor) is

ideal, and therefore the high level of the pullup is equal to VPU. In order to meet the VIH spec of the

DS18B20-PAR, the actual supply rail for the strong pullup transistor must include margin for the

voltage drop across the transistor when it is turned on; thus: VPU_ACTUAL = VPU_IDEAL + VTRANSISTOR.

3. See typical performance curve in Figure 16.

4. Logic low voltages are specified at a sink current of 4 mA.

5. To always guarantee a presence pulse under low voltage parasite power conditions, VILMAX may have

to be reduced to as low as 0.5V.

6. Logic high voltages are specified at a source current of 1 mA.

7. Active current refers to supply current during active temperature conversions or EEPROM writes.

8. DQ line is high (“hi-Z” state).

9. Drift data is based on a 1000 hour stress test at 125°C.

AC ELECTRICAL CHARACTERISTICS: NV MEMORY

(-55°C to +100°C; VPU=3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS

NV Write Cycle Time twr 210 ms

EEPROM Writes NEEWR -55°C to +55°C 50k writes

EEPROM Data Retention tEEDR -55°C to +55°C 10 years

DS18B20-PAR

18 of 19

AC ELECTRICAL CHARACTERISTICS (-55°C to +100°C; VPU=3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Temperature Conversion tCONV 9-bit resolution 93.75 ms 1

Time 10-bit resolution 187.5 ms 1

11-bit resolution 375 ms 1

12-bit resolution 750 ms 1

Time to Strong Pullup

tSPON Start Convert T or

Copy Scratchpad

Command Issued

10 µs

Time Slot tSLOT 60 120 µs 1

Recovery Time tREC 1µs1

Write 0 Low Time rLOW0 60 120 µs 1

Write 1 Low Time tLOW1 115µs1

Read Data Valid tRDV 15 µs 1

Reset Time High tRSTH 480 µs 1

Reset Time Low tRSTL 480 960 µs 1,2

Presence Detect High tPDHIGH 15 60 µs 1

Presence Detect Low tPDLOW 60 240 µs 1

Capacitance CIN/OUT 25 pF

NOTES:

1. Refer to timing diagrams in Figure 17.

2. If tRSTL > 960 ms, a power on reset may occur.

TYPICAL PERFORMANCE CURVE Figure 16

DS18B20-PAR Typical Error Curve

-0.5

-0.4

-0.3

-0.2

-0.1

0.1

0.2

0.3

0.4

0.5

0 10203040506070

Reference Temp (C)

Thermometer Error (C)

Mean Error

+3s Error

-3s Error

DS18B20-PAR

19 of 19

TIMING DIAGRAMS Figure 17