LM555CMX - ON SEMICONDUCTOR - Datasheet.Global

To learn more about ON Semiconductor, please visit our website at

www.onsemi.com

Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers

will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor

product management systems do not have the ability to manage part nomenclature that utilizes an underscore

(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain

device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated

device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please

email any questions regarding the system integration to Fairchild_questions@onsemi.com.

Is Now Part of

ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number

of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right

to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and speciﬁcally disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON

Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON

Semiconductor data sheets and/or speciﬁcations can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s

technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA

Class 3 medical devices or medical devices with a same or similar classiﬁcation in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended

or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its ofﬁcers, employees, subsidiaries, afﬁliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out

of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor

is an Equal Opportunity/Afﬁrmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

LM555 — Single Timer

LM555 Rev. 1.1.0 1

January 2013

LM555

Single T i mer

Features

• High-Current Drive Capabili ty: 200 mA

• Adjustable Duty Cycle

• Temperature Stability of 0.005%/°C

• Timing From μs to Hours

• Turn off Time Less Than 2 μs

Applications

• Precision Timing

• Pulse Generati on

• Delay Generati on

• Sequential Timing

Ordering Information

Part Number Operating Temperature Range Top Mark Package Packing Method

LM555CN 0 ~ +70°C LM555CN DIP 8L Rail

LM555CM LM555CM SOIC 8L Rail

LM555CMX LM555CM SOIC 8L Tape & Reel

Description

The LM555 is a highly stable controller capable of pro-

ducing accura te timing pulse s. With a mon ostabl e opera-

tion, the delay is controlled by one external resistor and

one capacitor. With astable operation, the frequency and

duty cycle are accurately controlled by two external

resistors and one capacitor.

8-DIP

8-SOIC

LM555 — Single Timer

LM555 Rev. 1.1.0 2

Block Diagram

Figure 1. Block Diagram

Absolute Maximum Ratings

Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be opera-

ble above the re co mmen ded operating conditions and s tres si ng the parts to these level s i s not recommended. In addi-

tion, extended exposure to stresses above the recommended operating conditions may affect device reliability. The

absolute maximum ratings are stress ratings only. Values are at TA = 25°C unless otherwise noted.

Symbol Parameter Value Unit

VCC Supply Voltage 16 V

TLEAD Lead Temperature (S oldering 10s) 300 °C

PDPower Dissipation 600 mW

TOPR Operating Temperature Range 0 ~ +70 °C

TSTG Storage Temperature Range -65 ~ +150 °C

F/F

OutPut

Stage

RRR

Comp.

Discharging Tr.

Vref

Vcc

Discharge

Threshold

Control

Voltage

GND

Trigger

Output

Reset

GND

Trigger

Output

Reset

VCC

Discharge

ThresholdControl

Voltage

Threshold

VREF

Discharging Tr ansistor

LM555 — Single Timer

LM555 Rev. 1.1.0 3

Electrical Characteristics

Values are at TA = 25°C, VCC = 5 ~ 15 V unless otherwise specified.

Notes:

1. When the output is high, the supply current is typically 1 mA less than at VCC = 5 V.

2. Tested at VCC = 5.0 V and VCC = 15 V.

3. These parameters, although guaranteed, are not 100% tested in production.

4. This determines the maximum value of RA + RB for 15 V operation, the maximum total R = 20 MΩ, and for 5 V

operation, the maximum total R = 6.7 MΩ.

Parameter Symbol Conditions Min. Typ. Max. Unit

Supply Voltage VCC 4.5 16.0 V

Supply Current (Low Stable) (1) ICC VCC = 5 V, RL = ∞36mA

VCC = 15 V, RL = ∞7.5 15.0 mA

Timing Error (Monostable)

Initial Accuracy (2) ACCUR RA = 1 kΩ to100 kΩ

C = 0.1 μF

1.0 3.0 %

Drift with Temperature (3) Δt / ΔT50ppm / °C

Drift with Supply Voltage (3) Δt / ΔVCC 0.1 0.5 % / V

Timing Error (Astable)

InItial Accuracy (2) ACCUR RA = 1 kΩ to 100kΩ

C = 0.1 μF

2.25 %

Drift with Temperature (3) Δt / ΔT 150 ppm / °C

Drift with Supply Voltage (3) Δt / ΔVCC 0.3 % / V

Control Voltage VCVCC = 15 V 9.0 10.0 11.0 V

VCC = 5 V 2.60 3.33 4.00 V

Threshold Voltage VTH VCC = 15 V 10.0 V

VCC = 5V 3.33 V

Threshold Current (4) ITH 0.10 0.25 μA

Trigger Voltage VTR VCC = 5 V 1.101.672.20 V

VCC = 15 V 4.5 5.0 5.6 V

Trigger Current ITR VTR = 0 V 0.01 2.00 μA

Reset Voltage VRST 0.4 0.7 1.0 V

Reset Current IRST 0.1 0.4 mA

Low Output Voltage VOL VCC = 15 V ISINK = 10 mA 0.06 0.25 V

ISINK = 50 mA 0.30 0.75 V

VCC = 5 V, ISINK = 5 mA 0.05 0.35 V

High Output Voltage VOH VCC = 15 V ISOURCE = 200 mA 12.5 V

ISOURCE = 100 mA 12.75 13.30 V

VCC = 5 V, ISOURCE = 100 mA 2.75 3.30 V

Rise Time of Output(3) tR100 ns

Fall Time of Output(3) tF100 ns

Discharge Leaka ge Curre nt ILKG 20 100 nA

LM555 — Single Timer

LM555 Rev. 1.1.0 4

Application Information

Table 1 below is the basic operating t able of 555 timer.

When the low signa l input is appli ed to the reset te rminal, the timer outpu t remains low reg ardless of the thr eshold vo lt-

age or the trig ger volt age. Only when the high s ignal is app lied to the res et terminal, the timer's output ch anges acco rd-

ing to threshol d voltage and trigger voltage.

When the threshold voltage exceeds 2/3 of the supply voltage while the timer output is high, the timer's internal dis-

charge transi sto r turns on, lowering the thresho ld voltage to below 1/3 of the supply voltage. Du rin g th is ti me , t he timer

output is maintained low. Later, if a low signal is applied to the trigger voltage so that it becomes 1/3 of the supply volt-

age, the timer's internal discharge transistor turns off, increasing the threshold voltage and driving the timer output

again at high.

1. Monostable Operation

Table 1. Basic Operating Table

Reset

(PIN 4) VTR

(PIN 2) VTH

(PIN 6) Output

(PIN 3)

Discharging

Transistor

(PIN 7)

Low X X Low ON

High < 1/3 VCC XHighOFF

High > 1/3 VCC > 2/3 VCC Low ON

High > 1/3 VCC < 2/3 VCC Previous State

Figure2. Monostable Circuit Figure 3. Resistance and Capacitance vs.

Time Delay (tD)

Figure 4. Waveforms of Monostable Operation

RESET Vcc

DISCH

THRES

CONT

GND

OUT

TRIG

+Vcc

C2RL

Trigger

10-5 10-4 10-3 10-2 10-1 100101102

10-3

10-2

10-1

100

101

102

10MΩ

1MΩ

10kΩ

100kΩ

RA=1kΩ

Capacitance(uF)

Time Delay(s)

LM555 — Single Timer

LM555 Rev. 1.1.0 5

1. Monostable Operation

Figure 2 illustrates a mono stable circuit. In this mode, the timer genera tes a fixe d pul se whe nev er the trigg er voltage

falls below VCC/3. When the trigger pulse voltage applied to the #2 pin falls below VCC/3 while the timer output is low,

the timer's intern al flip -flo p turns the discharging transistor off and causes the timer output to be co me hig h by cha rgi ng

the external capacitor C1 and setting the flip-flop output at the same time.

The voltage across the external capacitor C1, VC1 increases exponentially with the time constant t = RA*C and

reaches 2 VCC/3 at tD = 1.1 RA*C. Hence, capacitor C1 is charged through resistor RA. The greater the time constant

RAC, the longer it takes for the VC1 to reac h 2 VCC/3. In other words, the time constant RAC controls the output pulse

width.

When the applied vo ltage to the capacitor C1 reaches 2 VCC/3, the compa rato r on t he tri gg er te rmi na l res ets the flip-

flop, turning the discharging transistor on. At this time, C1 begins to discharge and the timer output converts to low.

In this way, the timer operating in the monostable repeats the above process. Figure 3 shows the time constant rela-

tionship based on RA and C. Figure 4 shows the general waveforms during the monostable operation.

It must be noted that, for a normal operation, the trigger pulse voltage needs to maintain a minimum of VCC/3 before

the timer output turns low. That is, although the output remains unaffected even if a different trigger pulse is applied

while the output is high, it may be affected and the waveform does not operate properly if the trigger pulse voltage at

the end of the output pulse remains at below VCC/3. Figure 5 shows such a timer output abnormality.

2. Astable Operation

Figure 5. Waveforms of Monostable Operation

(abnormal)

Figure 6. A Stable Circuit Figure 7. Capacitance and Resistance vs. Frequency

RESET Vcc

DISCH

THRES

CONT

GND

OUT

TRIG

+Vcc

C2RL

100m 1 10 100 1k 10k 100k

1E-3

0.01

0.1

100

10MΩ

1MΩ

100kΩ

10kΩ

1kΩ

(RA+2RB)

Capacitance(uF)

Frequency(Hz)

LM555 — Single Timer

LM555 Rev. 1.1.0 6

An astab le timer ope ration is ac hieved b y adding res istor RB to Figure 2 a nd config uring as shown on Fi gure 6. In t he

astable operati on, the trig ger terminal and the thresh old termin al are con necte d so that a se lf-trig ger is formed , operat-

ing as a multi -vi brator . Whe n the timer output is high, its internal discharging tran si st or. turns off and the VC1 increases

by exponential function with the time constant (RA+RB)*C.

When the VC1, or the threshold voltage, reaches 2 VCC/3; the comparator output on the trigger terminal becomes

high, resetti ng the F/ F and causing the timer o utp ut to bec ome lo w. This turns on the d is ch arg ing tra ns is tor an d the C1

discharges through the discharging channel formed by RB and the discharging transistor. When the VC1 falls below

VCC/3, the comparator output on the trigger terminal becomes high and the timer output becomes high again. The dis-

charging transistor turns off and the VC1 rises again.

In the above proc ess, the secti on where the timer o utput is high is t he time it t akes for the V C1 to rise from VCC/3 to 2

VCC/3, and the section where the timer output is low is the time it takes for the VC1 to drop from 2 VCC/3 to VCC/3.

When timer output is high, the equivalent circuit for charging capacitor C1 is as follows:

Since the duration of the timer output high state (tL) is the amount of time it takes for the VC1(t) to reach 2 VCC/3,

Figure 8. Waveforms of Astable Operation

Vcc

RARB

C1 Vc1

(0-)=Vcc/3

C1dvc1

------------- Vcc V0-()–

RARB

-------------------------------=1()

VC1 0+() VCC 3⁄=2()

VC1 t() VCC 12

---e

-t

RARB

+()C1

-------------------------------------

–





–







=3()

VC1 t() 2

---VCC V= CC 12

---e

-tH

RARB

+()C1

-------------------------------------

–







–







=4()

tHC1RARB

+()In2 0.693 RARB

+()C1

==5()

LM555 — Single Timer

LM555 Rev. 1.1.0 7

The equivalent circuit for discharging capacitor C1, when timer output is low is, as follows:

Since the duration of the timer output low state (tL) is the amount of time it takes for the VC1(t) to reach VCC/3,

Since RD is normally RB>>RD although related to the size of discharging transistor,

tL = 0.693RBC1 (10)

Consquently, if the timer operates in astable, the period is the same with

't = tH+tL = 0.693(RA+RB)C1+0.693RBC1 = 0.693(RA+2RB)C1'

because the period is the sum of the charge time and discharge time. Since frequency is the reciprocal of the period,

the following applies:

VC1(0-)=2Vcc/3

C1dvC1

---------------1

RARB

----------------------- VC1 0=+6()

VC1 t() 2

---VCCe

-t

RARD

+()C1

-------------------------------------

=7()

--- VCC 2

--- VCCe

-tL

RARD

+()C1

-------------------------------------

=8()

tLC1RBRD

+()In2 0.693 RBRD

+()C1

== 9()

frequency, f 1

---1.44

RA2RB

+()C1

----------------------------------------== 11()

LM555 — Single Timer

LM555 Rev. 1.1.0 8

3. Frequency Divider

By adjusting the length of the timing cycle, the basic circuit of Figure 1 can be made to operate as a frequency divider.

Figure 9. illustrates a divide-by-three circuit that makes use of the fact that retriggering cannot occur during the timing

cycle.

4. Pulse Width Modulation

The timer output waveform may be changed by modulating the control voltage applied to the timer's pin 5 and chang-

ing the referenc e of the timer's internal comparators. Figure 10 illustrates the pulse width modulation circuit.

When the continu ous trigger puls e train is appli ed in the monost able mode , the timer outp ut width is modulated ac cord-

ing to the signal applied to the control terminal. Sine wave, as well as other waveforms, may be applied as a signal to

the control terminal. Figure 11 shows the example of pulse width modulation waveform.

Figure 9. Waveforms of Frequency Divider Operation

Figure 10. Circuit for Pulse Width Modulation Figure 11. Waveforms of Pulse Width Modulation

CONT

GND

Vcc

DISCH

THRES

RESET

TRIG

OUT

+Vcc

Trigger

Output Input

LM555 — Single Timer

LM555 Rev. 1.1.0 9

5. Pulse Position Modulation

If the modulating signal is applied to the control terminal while the timer is connected for the astable operation, as in

Figure 12, the timer becomes a pulse position modulator.

In the pulse position modulator, the reference of the timer's internal comparators is modulated, which modulates the

timer output ac cording to the modulation signal applied to the control terminal.

Figure 13 illu strates a si ne wave for mo dulation si gnal and the resulting ou tput pulse po sition modula tion; howe ver, any

wave shape be used.

6. Linear Ramp

When the pull -up resistor RA in the monostable circuit shown in Figure 2 is replaced with constant current source, the

VC1 increases linearly, generating a linear ramp. Figure 14 shows the linea r ramp generating c ircuit and Fig ure 15 illus-

trates the generated linear ramp waveforms.

Figure 12. Circuit for Pulse Position Modluation Figure 13. Wafeforms of pulse position modulation

Figure 14. Circuit for Linear Ramp Figure 15. Waveforms of Linear Ramp

CONT

GND

Vcc

DISCH

THRES

RESET

TRIG

OUT

+Vcc

Modulation

Output

RESET Vcc

DISCH

THRES

CONT

GND

OUT

TRIG

+Vcc

Output

LM555 — Single Timer

LM555 Rev. 1.1.0 10

In Figure 14, current source is created by PNP transistor Q1 and resistor R1, R2, and RE.

For example, if VCC = 15 V, RE = 20 kΩ, R1 = 5 kΩ, R2 = 10 kΩ, and VBE = 0.7 V,

VE=0.7 V+10 V=10.7 V, and

IC=(15-10.7) / 20 k=0.215 mA.

When the trigg er st art s in a time r con figured as s hown i n Fig ure 14 , the cu rrent fl owing through cap a citor C1 bec omes

a constant current generated by PNP transistor and re sistors.

Hence, the VC is a linea r ramp func tion a s sh own in Figu re 15. The g radien t S of the line ar ramp f uncti on is defin ed as

follows:

Here the Vp-p is the peak-to-peak voltage.

If the electric charge amount accumulated in the capacitor is divided by the capacitance, the VC comes out as follows:

V = Q/C (15)

The above equation divided on both sides by t gives:

and may be simplified into the following equation:

S = I/C (17)

In other words, the gradient of the linear ramp function appearing across the capacitor can be obtained by using the

constant current flowing through the capacitor.

If the const a nt cu rrent flow through the capaci tor is 0.215 mA an d th e ca pacitance is 0.02 μF, the gradient of the ra mp

function at both ends of the capacitor is S = 0.215 m / 0.022 μ = 9.77 V/ms.

ICVCC VE

–

---------------------------=12()

Here, VE is

VEVBE R2

R1R2

----------------------VCC

+=13()

SVpp–

----------------=14()

----Qt§

-------------=16()

LM555 — Single Timer

LM555 Rev. 1.1.0 11

Physical Dimensions

Figure 16. 8-Lead, DIP, JEDEC MS-001, 300" WIDE

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner

without notic e. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor represe ntative to verify or

obtain the most recent revision. Package specifica tions do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the

warranty therein, which covers Fairchild produ cts.

Always visit Fairchild Semiconduct or’s online packaging are a for the most recent package drawings :

http://www.fairchildsemi.com/packaging/.

For current tape an d reel specifications, visit Fair child Semiconductor’s online pac kaging area:

http://www.fairchildsemi.com/products/discrete/pdf/8dip_tr.pdf.

7° TYP

.430 MAX

[10.92]

A.400

.373 [10.15

9.46 ]

.250±.005 [6.35±0.13]

.036 [0.9 TYP]

.070

.045 [1.78

1.14]

.100

[2.54]

.300

[7.62]

.060 MAX

[1.52]

.310±.010 [7.87±0.25]

.130±.005 [3.3±0.13]

.210 MAX

[5.33]

.140

.125 [3.55

3.17]

.015 MIN

[0.38]

.021

.015 [0.53

0.37]

.010+.005

-.000 [0.254+0.127

-0.000 ]

PIN #1

(.032) [R0.813]

(.092) [Ø2.337]

TOP VIEW

OPTION 1

TOP VIEW

OPTION 2

.001[.025] C

N08EREVG

C. DOES NOT INCLUDE MOLD FLASH OR PROTRUSIONS.

DAMBAR PROTRUSIONS SHALL NOT EXCEED

D. DOES NOT INCLUDE DAMBAR PROTRUSIONS.

B. CONTROLING DIMENSIONS ARE IN INCHES

A. CONFORMS TO JEDEC REGISTRATION MS-001,

MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED

VARIATIONS BA

E. DIMENSIONING AND TOLERANCING

NOTES:

REFERENCE DIMENSIONS ARE IN MILLIMETERS

.010 INCHES OR 0.25MM.

PER ASME Y14.5M-1994.

8-DIP

LM555 — Single Timer

LM555 Rev. 1.1.0 12

Physical Dimensions (continued)

Figure 17. 8-Lead, SOIC,JEDEC MS-012, 150" NARROW BODY

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner

without notic e. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor represe ntative to verify or

obtain the most recent revision. Package specifica tions do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the

warranty therein, which covers Fairchild produ cts.

Always visit Fairchild Semiconduct or’s online packaging are a for the most recent package drawings :

http://www.fairchildsemi.com/packaging/.

For current tape an d reel specifications, visit Fair child Semiconductor’s online pac kaging area:

http://www.fairchildsemi.com/dwg/M0/M08A.pdf.

8-SOIC

TRADEMARKS

The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not

intended to be an exhaustive list of all such trademarks.

2Cool¥

AccuPower¥

AX-CAP¥*

BitSiC¥

Build it Now¥

CorePLUS¥

CorePOWER¥

CROSSVOLT¥

CTL¥

Current Transfer Logic¥

DEUXPEED

Dual Cool™

EcoSPARK

EfficientMax¥

ESBC¥

Fairchild

Fairchild Semiconductor

FACT Quiet Series¥

FACT

FAST

FastvCore¥

FETBench¥

FPS¥

F-PFS¥

FRFET

Global Power Resource

GreenBridge¥

Green FPS¥

Green FPS¥ e-Series¥

Gmax¥

GTO¥

IntelliMAX¥

ISOPLANAR¥

Making Small Speakers Sound Louder

and Better™

MegaBuck¥

MICROCOUPLER¥

MicroFET¥

MicroPak¥

MicroPak2¥

MillerDrive¥

MotionMax¥

mWSaver¥

OptoHiT¥

OPTOLOGIC

OPTOPLANAR

PowerTrench

PowerXS™

Programmable Active Droop¥

QFET

QS¥

Quiet Series¥

RapidConfigure¥

Saving our world, 1mW/W/kW at a time™

SignalWise¥

SmartMax¥

SMART START¥

Solutions for Your Success¥

SPM

STEALTH¥

SuperFET

SuperSOT¥-3

SuperSOT¥-6

SuperSOT¥-8

SupreMOS

SyncFET¥

Sync-Lock™

The Power Franchise

TinyBoost¥

TinyBuck¥

TinyCalc¥

TinyLogic

TINYOPTO¥

TinyPower¥

TinyPWM¥

TinyWire¥

TranSiC¥

TriFault Detect¥

TRUECURRENT

PSerDes¥

UHC

Ultra FRFET¥

UniFET¥

VCX¥

VisualMax¥

VoltagePlus¥

XS™

* Trademarks of System General Corporation, used under license by Fairchild Semiconductor.

DISCLAIMER

FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE

RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT

OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE

SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN,

WHICH COVERS THESE PRODUCTS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE

EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.

As used herein:

1. Life support devices or systems are devices or systems which, (a) are

intended for surgical implant into the body or (b) support or sustain

life, and (c) whose failure to perform when properly used in

accordance with instructions for use provided in the labeling, can be

reasonably expected to result in a significant injury of the user.

2. A critical component in any component of a life support, device, or

system whose failure to perform can be reasonably expected to

cause the failure of the life support device or system, or to affect its

safety or effectiveness.

ANTI-COUNTERFEITING POLICY

Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com,

under Sales Support.

Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their

parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed

applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the

proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild

Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors

are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical

and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise.

Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global

problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors.

PRODUCT STATUS DEFINITIONS

Definition of Terms

Datasheet Identification Product Status Definition

Advance Information Formative / In Design Datasheet contains the design specifications for product development. Specifications may change

in any manner without notice.

Preliminary First Production

Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild

Semiconductor reserves the right to make changes at any time without notice to improve design.

No Identification Needed Full Production Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make

changes at any time without notice to improve the design.

Obsolete Not In Production Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor.

The datasheet is for reference information only.

Rev. I63

www.onsemi.com

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent

coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.

ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,

regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer

application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not

designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification

in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized

application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and

expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such

claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This

literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

www.onsemi.com

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative