LM185-1.2/LM285-1.2/LM385-1.2 Micropower Voltage Reference Diode General Description The LM185-1.2/LM285-1.2/LM385-1.2 are micropower 2-terminal band-gap voltage regulator diodes. Operating over a 10 A to 20 mA current range, they feature exceptionally low dynamic impedance and good temperature stability. On-chip trimming is used to provide tight voltage tolerance. Since the LM185-1.2 band-gap reference uses only transistors and resistors, low noise and good long term stability result. Careful design of the LM185-1.2 has made the device exceptionally tolerant of capacitive loading, making it easy to use in almost any reference application. The wide dynamic operating range allows its use with widely varying supplies with excellent regulation. The extremely low power drain of the LM185-1.2 makes it useful for micropower circuitry. This voltage reference can be used to make portable meters, regulators or general purpose analog circuitry with battery life approaching shelf life. Further, the wide operating current allows it to replace older references with a tighter tolerance part. The LM185-1.2 is rated for operation over a -55C to 125C temperature range while the LM285-1.2 is rated -40C to 85C and the LM385-1.2 0C to 70C. The LM185-1.2/ LM285-1.2 are available in a hermetic TO-46 package and the LM285-1.2/LM385-1.2 are also available in a low-cost TO-92 molded package, as well as SO and SOT-23. The LM185-1.2 is also available in a hermetic leadless chip carrier package. Features n n n n n n n 4 mV ( 0.3%) max. initial tolerance (A grade) Operating current of 10 A to 20 mA 0.6 max dynamic impedance (A grade) Low temperature coefficient Low voltage reference -- 1.235V 2.5V device and adjustable device also available LM185-2.5 series and LM185 series, respectively Connection Diagrams SOT23 T0-92 Plastic Package (Z) DS005518-33 * Pin 3 is attached to the Die Attach Pad (DAP) and should be connected to Pin 2 or left floating. DS005518-10 Order Number LM385M3-1.2 See NS Package Number MA03B Bottom View Order Number LM285Z-1.2, LM285BXZ-1.2, LM285BYZ-1.2 LM385Z-1.2, LM385BZ-1.2 LM385BXZ-1.2 or LM385BYZ-1.2 See NS Package Number Z03A (c) 2000 National Semiconductor Corporation DS005518 www.national.com LM185-1.2/LM285-1.2/LM385-1.2 Micropower Voltage Reference Diode January 2000 LM185-1.2/LM285-1.2/LM385-1.2 Connection Diagrams (Continued) SO Package DS005518-9 Order Number LM285M-1.2, LM285BXM-1.2, LM285BYM-1.2 LM385M-1.2, LM385BM-1.2 LM385BXM-1.2 or LM385BYM-1.2 See NS Package Number M08A TO-46 Metal Can Package (H) DS005518-6 Bottom View Order Number LM185H-1.2, LM185H-1.2/883, LM185BXH-1.2, LM185BYH-1.2 LM285H-1.2 or LM285BXH-1.2 See NS Package Number H02A www.national.com 2 Storage Temperature -55C to +150C Soldering Information TO-92 package: 10 sec. 260C TO-46 package:10 sec. 300C SO and SOT Pkg. Vapor phase (60 sec.) 215C Infrared (15 sec.) 220C See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for other methods of soldering surface mount devices. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (Note 2) Reverse Current Forward Current Operating Temperature Range (Note 3) LM185-1.2 LM285-1.2 LM385-1.2 30 mA 10 mA -55C to +125C -40C to +85C 0C to 70C Electrical Characteristics (Note 4) LM185-1.2 Parameter Conditions Typ LM185BX-1.2 LM385B-1.2 LM185BY-1.2 LM385BX-1.2 LM285-1.2 LM385BY-1.2 LM385-1.2 Units LM285BX-1.2 (Limit) LM285BY-1.2 Reverse Breakdown TA = 25C, Voltage 10 A IR 20 mA 1.235 Minimum Operating 8 Current LM385M3-1.2 Reverse Breakdown 10 A IR 1 mA Tested Design Tested Design Tested Limit Limit Limit Limit Limit Design Limit (Notes 5, 8) (Note 6) (Note 5) (Note 6) (Note 5) (Note 6) 1.223 1.223 1.205 V(Min) 1.247 1.247 1.260 V(Max) 10 1 20 15 1.5 1 20 1.5 15 20 A 10 15 (Max) 1 1.5 Voltage Change 1 mA IR 20 mA with Current mV (Max) 10 20 20 25 20 25 mV (Max) IR = 100 A, f = 20 Hz 1 Wideband Noise IR = 100 A, 60 V (rms) 10 Hz f 10 kHz 20 ppm Reverse Dynamic Impedance Long Term Stability IR = 100 A, T = 1000 Hr, TA = 25C 0.1C Average Temperature Coefficient (Note 7) IR = 100 A X Suffix 30 30 Y Suffix 50 50 All Others 150 ppm/C ppm/C 150 150 ppm/C (Max) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Refer to RETS185H-1.2 for military specifications. Note 3: For elevated temperature operation, Tj max is: LM185 150C LM285 125C LM385 100C Thermal Resistance JA (junction to ambient) TO-92 TO-46 SO-8 SOT23 180C/W (0.4" leads) 440C/W 165C/W 283C/W 80C/W N/A N/A 170C/W (0.125" leads) JC (junction to case) N/A Note 4: Parameters identified with boldface type apply at temperature extremes. All other numbers apply at TA = TJ = 25C. 3 www.national.com LM185-1.2/LM285-1.2/LM385-1.2 Absolute Maximum Ratings (Note 1) LM185-1.2/LM285-1.2/LM385-1.2 Electrical Characteristics (Note 4) (Continued) Note 5: Guaranteed and 100% production tested. Note 6: Guaranteed, but not 100% production tested. These limits are not used to calculate average outgoing quality levels. Note 7: The average temperature coefficient is defined as the maximum deviation of reference voltage at all measured temperatures between the operating TMAX and TMIN, divided by TMAX - TMIN. The measured temperatures are -55C, -40C, 0C, 25C, 70C, 85C, 125C. Note 8: A military RETS electrical specification is available on request. Typical Performance Characteristics Reverse Characteristics Reverse Characteristics DS005518-13 Temperature Drift of 3 Representative Units Forward Characteristics DS005518-14 Reverse Dynamic Impedance DS005518-15 Reverse Dynamic Impedance DS005518-18 DS005518-17 DS005518-16 Noise Voltage Filtered Output Noise DS005518-20 DS005518-19 www.national.com Response Time 4 DS005518-21 Wide Input Range Reference Micropower Reference from 9V Battery Reference from 1.5V Battery DS005518-22 DS005518-23 DS005518-8 Micropower* 5V Regulator Micropower* 10V Reference DS005518-25 *IQ 20 A standby current DS005518-24 *IQ 30 A Precision 1 A to 1 mA Current Sources DS005518-27 DS005518-26 5 www.national.com LM185-1.2/LM285-1.2/LM385-1.2 Typical Applications LM185-1.2/LM285-1.2/LM385-1.2 Typical Applications (Continued) METER THERMOMETERS Lower Power Thermometer 0C-100C Thermometer DS005518-29 *2N3638 or 2N2907 select for inverse HFE 5 Select for operation at 1.3V IQ 600 A to 900 A DS005518-28 Calibration 1. Short LM385-1.2, adjust R3 for IOUT = temp at 1 A/K 2. Remove short, adjust R2 for correct reading in centigrade IQ at 1.3V 500 A IQ at 1.6V 2.4 mA 0F-50F Thermometer Micropower Thermocouple Cold Junction Compensator DS005518-30 Calibration 1. Short LM385-1.2, adjust R3 for IOUT = temp at 1.8 A/K 2. Remove short, adjust R2 for correct reading in F DS005518-31 Adjustment Procedure 1. Adjust TC ADJ pot until voltage across R1 equals Kelvin temperature multiplied by the thermocouple Seebeck coefficient. 2. Adjust zero ADJ pot until voltage across R2 equals the thermocouple Seebeck coefficient multiplied by 273.2. Thermocouple Seebeck R1 R2 Voltage Voltage Type Coefficient () () Across R1 Across R2 @ 25C (mV) (V/C) (mV) J 52.3 523 1.24k 15.60 14.32 T 42.8 432 1k 12.77 11.78 K 40.8 412 953 12.17 11.17 S 6.4 63.4 150 1.908 1.766 Typical supply current 50 A www.national.com 6 LM185-1.2/LM285-1.2/LM385-1.2 Typical Applications (Continued) Centigrade Thermometer DS005518-1 Calibration 1. Adjust R1 so that V1 = temp at 1 mV/K 2. Adjust V2 to 273.2 mV IQ for 1.3V to 1.6V battery voltage = 50 A to 150 A Schematic Diagram DS005518-7 7 www.national.com LM185-1.2/LM285-1.2/LM385-1.2 Physical Dimensions inches (millimeters) unless otherwise noted TO-46 Metal Can Package (H) Order Number LM185H-1.2, LM185H-1.2/883, LM185BXH-1.2, LM185BYH-1.2, LM285H-1.2, or LM285BXH-1.2 NS Package Number H02A SOT-23 Package (M3) Order Number LM385M3-1.2 NS Package Number MA03B www.national.com 8 LM185-1.2/LM285-1.2/LM385-1.2 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Small Outline (SO-8) Package Order Number LM285M-1.2, LM285BXM-1.2, LM285BYM-1.2 LM385M-1.2, LM385BM-1.2, LM385BXM-1.2, LM385BYM-1.2 NS Package Number M08A TO-92 Plastic Package (Z) Order Number LM285Z-1.2, LM285BXZ-1.2 LM285BYZ-1.2, LM385Z-1.2, LM385BZ-1.2 LM385BXZ-1.2 or LM385BYZ-1.2 NS Package Number Z03A 9 www.national.com LM185-1.2/LM285-1.2/LM385-1.2 Micropower Voltage Reference Diode Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.